8.50 Cage Installed in our "BUDGET" S10 Creampuff
1 Video View·Aug 16, 2026
AI Generated·May contain errors
Welcome back to CJ Racecar's YouTube channel.
We're back working on Cream Puff, our budget S10 build.
I know we've been off budget just a little bit,
but we did get some parts in this week
that are gonna average our budget back out a little bit.
Hopefully they work.
We'll have to check them out.
We also got the cage in
and they're working on putting that in now.
Also, we're planning on running sick week,
which is about a month away.
So Ricky's got a lot of work to do and it's off time.
But we know this engine is probably not gonna hold up
really long because it's literally a junkyard engine
that we're doing zero work to.
Gapping rings, we're not doing anything.
We're just gonna put turbos on it
and run it till it blows up.
So at some point we will need another engine.
And if we're gonna run sick week,
we need to get an engine really soon.
We asked everybody about the cage.
You guys said you wanted a pre-bent,
pre-notched cage to save us some time.
And that's what we did.
So we wanted to ask you guys what you think of an engine.
Should we build something
or should we get with Pete Harold at HED
and just order us an engine
and have an engine ready to go for when this one blows up?
Let us know what you guys think in the comments below
and maybe we'll end up with a HED LS and cream pump.
So as you guys know, we blew this budget completely out.
But to make up for it,
we got some special items from Timu.
These were really cheap for what they are.
I don't remember exactly how much this piece was,
but it was a lot less than anywhere else we could find.
So hopefully this helps make up for the budget,
but let's get her opened up and see what's in here.
They got these China staples in here,
which are pretty, pretty rowdy.
Oh yeah.
This is going to be good.
I found this.
This isn't mine.
Oh yeah.
So this is a,
I think it said a thousand horsepower rated, I want to say.
So it should do us just fine,
but it's a four inch core intercooler from Timu.
That was, I'd have to go back and look,
but it was really cheap, really cheap.
Let's see what this looks like.
Dang.
Actually, it's not,
Ooh, we got a little,
we got us a little, a little ding there
as expected from Timu.
It's got a little mountain bungs on it.
This side, this side don't look that bad.
The other side's got a little ding though.
We'll be fine.
So we got something else here from Timu
and these are actually not bad.
I mean, some of the welds are kind of iffy, you know,
but it, they're a lot better than I expected for the cost
cause it came with both, both headers.
It came with the gaskets.
It came with the clamps, the V band clamps
and it came with these elbows with T4 flanges on them.
I believe what they are is T4.
I'd have to go back and look.
I think those are T4,
but these, these elbows that already have the V band
and the flange for the turbo on them.
So that's pretty, pretty cool.
I don't know if we'll use these or not,
but it is pretty cool that it came with it for the price
cause they were also really cheap.
Hopefully this helps us stay on budget
or at least get our budget closer to what it should be
before we completely blew it out of the water.
So these, these headers actually came with studs too,
which is unreal.
I've never, ever seen anything like it for,
I want to say they were like $160 for the set,
which is a pretty good deal for a set of stainless headers.
Even if it is made out of the crappiest stainless
you can get your hands on.
I like a glove, put one on the back for good measure.
Pretty good.
The flanges even line up with the head.
All right, let's grab the other one.
This side here is going to be a little tight
and I'll show you why here in a second.
This side is going to be a little bit of trouble.
Our steering column we got coming from motion race work
comes out of this hole right here.
And as you can see,
that hole lines up directly with this, this tube.
So we're going to have to get a little,
it might work to come through here maybe.
And even then you can see how tight it's going to be
because you're going to have a spark plug
coming out right in there somewhere.
I can't see it from where I'm at,
but there'll be a spark plug there.
So the steering on this side with this header
is going to be a little tricky,
but that's not my department.
So as far as I'm concerned,
these things are great for the budget.
Also pretty, pretty good looking.
Oh yeah.
JEGS offers this water pump kit for the LS.
It uses a big block Chevy style water pump,
standard big block Chevy, nothing special.
But then you get these,
I think they're ICT billet makes these,
but they're these adapter plates.
And these will bolt to the block somehow or another
like this or like this.
The big block Chevy water pump will bolt directly
to these adapter plates.
So we're going to see how well it works.
So these are, I don't know if they're 16 ORB fittings.
So you can have some AN fittings coming out of this
to return, that would return back to the radiator,
I believe.
So we'll have to plumb that up
and then the water pump will feed through here.
Yeah, that's how it works.
Shoot, almost like we're professionals.
We got some stuff in today.
We put a poll up on YouTube
and to see what you guys thought
if we should do a cage ourselves or order a cage.
So mostly everyone said let's order a cage.
So that's what we did.
So now we've got in today are more race chassis,
850 cage for an S10.
This is how it showed up on a pallet real nice,
banded down.
We opened a few things up just to check it out already.
Looks like it comes with everything.
It's got outriggers in the box,
even came with some stickers,
a Christmas tree ornament.
I mean, this thing, it's chromoly,
should cert 850, which is plenty
for what we're wanting to do right now.
I don't know if this is the right tool or not.
Someone in here said it might be.
It looks like it would work
if you know what you're doing with it,
which I apparently do not.
My next option is a piece of porcelain off a spark plug.
I think it's working.
That ain't doing nothing.
That's barely cutting the glue.
Oh, well that, we broke it,
but it seems every piece disappeared.
All right, let's see how well this works.
I'm gonna get the whole spark plug.
I'm gonna need a bigger piece.
All right, what are you trying to do?
Break this glass.
Really?
Yeah, why?
With what?
A piece of porcelain.
You want me to break it?
Holy cow.
You suck.
I told you to get a hammer.
That kind of hurt my wrist.
It hurt for her.
I'm going home.
Oh my gosh.
See?
I think we need something sharper.
I'll be right back.
Be strong.
Be stronger.
Bro, what is up with this thing?
Use the ball, there you go.
Okay, that was part of it.
Oh, don't hit the paint.
All right, hang on.
Roll it down.
Watch this.
We're gonna need a ratchet strap.
It ain't hardly got nothing on it.
Let's see if that'll go.
A little more.
A little bit more.
Shoot.
Cameron's gonna watch this video back
and be like, what were y'all doing?
Why don't y'all just tack the thing in?
That should stay.
Probably gonna fall off
and hit me right in the daggone head.
All right.
How's that?
Do it.
I think our string's gonna be in the way.
I'm gonna use my head.
I gotta figure out how to do this better.
You tell me when you're ready.
I'm gonna climb in here
and I'm gonna lift this thing with my back.
Okay.
Is this going too far?
You're gonna put it right there on my shoulders.
Yep, right there.
Right there.
Oh, there we go.
Yeah, but then your head's gonna.
How am I forward to back?
Am I too high?
What's going on?
What I would do is wherever you got it,
mark it and wherever it's at,
drop it, like we'll drop it a little bit
because I got it pushed pretty hard
against the headliner right now.
Okay.
Oh, golly.
Glass.
Oh, you got glass in here?
I thought you cleaned all that up.
Well, I vacuumed it,
but it's just dust.
Fit A pillars.
Attach.
Yeah.
Attach the A pillars.
Just says attach the A pillars.
If the rocker bar is level
and the main hoop is set correctly,
minimal shortening should be needed.
Notch the A pillars for the rocker bar
and tack them in place.
It gets a rocker bar?
Where does it go?
Underneath them?
Underneath, yeah.
Attaches from outrigger to outrigger.
Okay.
And the A pillar lands on a rocker or on the outrigger?
It lands on the outrigger,
but I think where they land,
they only put one notch in it.
Yeah, and they're saying if the main hoop's
in the right spot with the outrigger height
and we make the rocker bar level,
that means the front outrigger will be in the right spot,
which means the A pillar will land
where it's supposed to land.
Okay.
Throw that A pillar over there.
That's pretty close.
That's pretty darn close.
Yeah.
If he can hold 83 here,
I can put one tack on the front side.
Yeah.
To hold it?
Yeah, to hold it.
To tack on each side, okay.
Yeah.
We gotta take the ratchet strap off
and double check that
because it's holding it in a little bit.
Yeah.
So it may need to go.
Well, whenever you tack this side,
that's where it needs to be, though.
Yeah.
You can't tack this side in like this.
Well, no, no.
Let it go.
Yeah.
Oh, yeah.
And then measure.
Right.
From the frame out.
Yeah, yeah, yeah.
And then try to center from there.
All right.
Right there.
That's close.
If we zero it to that right there,
that'll be close.
Roughly three quarters of an inch.
Three quarters of an inch?
Yeah, three quarters of an inch needs to come off.
One side?
One side.
Okay.
Is that gonna suck it in enough?
No.
No?
We gotta figure that out.
Yeah.
But, I mean, it's gotta go in.
It's gotta go in roughly three inches.
You can make that work.
Oh, look at that.
I can feel that gap.
You can make that happen?
I can make it happen.
Hit it right there.
Right there?
Yeah.
You sure?
Yeah, I mean, 0.0 is pretty close.
Don't tell me we got to...
Come up in the back, right?
No, if it's level.
No, I mean this.
Where's the digital rocket?
Put that at seven.
What's that?
That's seven.
Is it?
Yeah.
It really can't go up.
It's up against it right here, isn't it?
And it's up against something right here.
No, it's close, though.
And right up here?
Yeah, it's hittin' there.
It's hittin' this box right here.
So that's not much of an option.
That's pretty much where she lands.
I think it'll be okay, though.
Yeah, I mean, it follows that A pillar perfectly.
It's down, then it, I mean, it's...
Look, I'll hold it, and you come back.
I think it's fine.
From where I'm standing.
Yeah.
You know what I mean?
It follows it perfect.
Tack it in.
We can't tack it in.
Why not?
Well, because we got to undo the main hoop
and get it right.
Oh, yeah.
But we got to put the rocker on that side.
Oh, yeah.
I was trying to peacock a little bit.
I mean, I could hold it, like, right...
I'll put a tack down in the front,
and then you can hold it and do whatever,
and we can, I can put a tack.
I can put one here, and then one out here.
We'll do it.
We'll do it real quick.
Grab your...
Grab.
Yeah.
Right?
Yeah.
It's like, it's got to be trimmed.
Huh?
Right?
Huh?
Yeah.
I don't know how much.
What if we do that?
Ha ha.
Good thing you didn't trim it like you wanted to.
I know.
What if we do that, Ricky?
Now it just falls in and out.
We're real smart, man.
I don't care what they say.
I never claimed to be.
We're real smart, man.
I never claimed to be.
Mark that.
Right here?
Yep.
Right on the edge.
Okay.
22?
Oh, God.
Oh, we're close.
Oh, we're real close.
What are we, less than...
We're about an eighth inch?
Put it at...
Put a mark at what?
22?
And then we'll just, we'll just pop it back.
He should have given us access
to the chassis jig for this truck.
It's worth it.
What's it look like from out front?
Let me...
I mean, I know I'm not on the 22 anymore.
Let me have a gander.
The windshield's really dirty.
So it was hard to see anything.
Sounds about right.
But from here, I don't think it looks that bad.
It's still going to be snug, but...
I'm going to knock these up some.
22 and I'm going to call it seven eighths.
Okay.
Just straight down from the inside of here
to the bottom of this tube.
Okay.
I mean, you're close.
Yeah, it's about the same 22 and seven eighths.
I could live...
I mean, it can come up a little bit, but not much.
I mean, it's sticking out the back glass right now, but...
Yeah, but see, technically,
I think where you're sitting,
the door bar would need to be here.
Mm-hmm, at your shoulder.
To go through your forearm.
Pretty much got to go.
The door will close there.
What is the door hitting?
When I just tried to close, did the door hit something?
No?
It's not hitting nothing, right?
Yeah, down here.
What's it hitting?
The main hoop.
The door is?
Mm-hmm.
Right here.
Oh.
Well, guess what?
Cut that.
No, that's fine.
I'm not worried about that.
What I'm worried about is the dam.
Like that.
I mean, it could drop a little bit,
but see your gap right here?
That's where you...
That's what you got to watch for.
We're better already.
Oh.
You know, it's almost like we planned this
because we couldn't win no further back.
This thing pretty much puts it where it has to go.
That didn't...
That's not like it shocked you.
That got you, didn't it?
Just a little bit.
Ha, ha, ha, ha, ha, ha, ha, ha, ha.
So, all we have left are the door bars
and the bars that run out back, right?
Yes.
And we can't do those until we drop the cage,
weld everything we could weld, then lift it back up.
Yeah.
So, we got to hold off on that.
So, this is pretty much...
Everything else is tacked in.
Yeah.
Ready to be dropped and welded.
Yeah.
All right.
Pretty smooth overall.
Yeah, I mean, everything...
We went by the instructions, seven degrees.
Everything fell into place.
Yeah.
The instructions recommend a drum roll
on a sanding drum roll,
which we put in a couple of joints
just to make them a little smoother
and just fell into place.
Yep.
I like it.
All right, that's pretty much going to do it
for today's video.
We got a cage all tacked up in cream puff.
I am glad we went with a pre-bent, pre-notched,
more race cars cage because it made our life a lot easier.
If we had to do this cage one-off
because we've never done one for an S10,
it would have definitely taken us a lot longer
than it did to put in this cage.
They make a really nice cage that fits good.
And even the notches, we hardly had to mess with at all.
If you're in a market for a cage for Mustang, S10,
they got a bunch of different stuff.
Get with more race cars.
It'll get you hooked up.
Make sure you like, share and subscribe
and we'll see you on the next one.

