🦀 I Made Vampire Crab Ecosystem Paludarium With Waterfall (Step By Step Guide)

Mini World Craft
6 followers
AI Generated·May contain errors
Video Summary
AI GeneratedThis video provides a step-by-step guide to building an affordable, low-maintenance rainforest cross-section paludarium for vampire crabs. The creator emphasizes a budget-friendly approach, avoiding expensive spray foams and utilizing natural materials to create a bioactive environment that mimics a rainforest stream bank.
Hello everyone, in this video I'm going to show you how to build a beautiful
affordable rainforest cross-section paludarium for vampire crabs.
Just like this one here and we're not going to be using any spray foams.
I call it a rainforest cross-section paludarium because it looks just like
what you would see if you were standing in the middle of a rainforest stream
looking at one of the banks. The best part about this build or
something very similar is that it's super low maintenance, super low cost and
the crabs absolutely love it. Plus you don't have to deal with any of
the dramas of spray foam. So let's just jump straight into it.
As with most of my builds the first thing to create is a land and water
barrier. This keeps the water section and the
land section separate and in this case we'll be creating
our river bank. I'm just using stones I found outside for this which is our
first step in keeping the cost down. The next thing I've added here is a
little pump to create a waterfall. This is optional, you don't necessarily
need this but I did want a little water feature in this tank and it's not going
to cost much extra to do anyway. So I've wrapped the pump head with some
foam just to stop the vibrations and I put some filter foam on the intake end
just to make sure it doesn't clog up and I've attached a little bit of tubing
just to create the waterfall. It's really simple and only takes a few
seconds to add to the tank. The next part of the process is to add
some substrate. For this I'm using leca or clay balls.
You can use a full layer of filter foam if you want but I prefer the clay balls.
They're really cheap, they work really well, they're great for
beneficial bacteria and they blend in really well with the rest of the scape.
Even though it's covered you do see it from the side sometimes and it doesn't
look as artificial as some other things. Just remember when you're putting this
stuff in always make sure you go a little bit higher
just to make sure that when you put the soil on top it doesn't sit in the water.
I generally like to leave a couple of centimeters or about an inch.
Once the substrate layer is in the next thing to do is to cover it over with
some sort of a barrier. For this I like to use weed matting but
you can use window screening. Pretty straightforward, just lay it across
the top of the surface of the substrate then you can start adding soil.
After adding the soil barrier you can add some soil. For this I'm just using
some organic fern mix. Any kind of soil is fine but I just use
this stuff because it's what I have lying around and I know that it works
really well. I generally try to go about an inch deep
or about five centimeters usually. There's no need to go that much deeper.
It's plenty enough for the crabs to burrow into,
plenty enough for the plants to grow. As the tank's only 30 centimeters high
we don't want to waste too much space with a big deep soil layer that's not
going to get used very efficiently. Once the soil layer is in I generally
like to add my hardscape and then after that I'll start adding the plants.
I already know where most of the plants are going to go so I'm going to get the
hardscape in and roughly plant things out around that.
You might remember this piece of hardscape from the previous biotope build.
It's going to fit really well into this one. It has a nice gentle
curvy slope and we're going to build on top of that. Again this is a no-cost
piece of hardscape. I just take some of this stuff from the
forest near my house. Just make sure when you do take stuff
like this you give it a good soak in some water,
let it dry out for a while and make sure you haven't imported any
ants, spiders, centipedes, whatever else you might have in your area.
Generally doing just a quick dip in some water and leaving it out to dry will get
rid of most of the creatures that are living inside something like this.
My plant selection in this build is going to be really simple. I'm going to
be using some ferns, some moss, some pilea which is what I'm
going to be adding first and then probably a little bit of ficus
It's another creeping plant, works really well and grows really well
in humid environments and gives a nice overgrown jungle look.
Adding ferns is always my favorite part of any build. As soon as you start adding
the ferns the whole build starts coming together
and it starts to look really established really quickly.
Especially when you get bigger ferns which are also generally quite cheap.
I forget exactly how much I paid for all of these plants but in total
probably around 15 US dollars roughly. So overall it's pretty good value because
they are quite big ferns. With all the main plants in now things
are starting to look really good. We're just going to add some moss then
add a little bit of the creeping plant, ficus pumila, and then we can start
adding the really really fine details in such as the sand,
some rocks into the water section, then we can start filling it up.
It's now time to add sand. You could use gravel for this but I'm just going to be
using some fine white sand. It's some stuff I had from the previous
build so I like to reuse it. Again that's going to keep it nice and cheap.
Plus the crabs really do prefer sand over gravel.
Sand is a little bit harder to keep clean but I personally think it's worth
the effort. Again you can choose whatever you like or
whatever you have lying around. The tank's basically ready to start
filling up now. I'm just going to be using some tap water for this.
Dechlorinated obviously. There's no need to use RO water remineralized in my area.
However if you do have some issues with pH definitely look into it but generally
for most people tap water is going to be fine as long as you add some
dechlorinator to it. So it's time to turn the pump on, check
out the waterfall and readjust the flow so that it's not streaming everywhere
and blowing sand around. To do this I'll just push it into place
and then dab a little bit of super glue between the pipe and the rock.
That'll hold it all in place nicely. I didn't end up filming the super gluing
part because it was a little bit tricky to try and get everything in there and
film it at the same time so I had to move the camera out of the way
just so I could get in with two hands and push down the rock and glue it.
The build is just about ready now to add some crabs but first I'm going to add
some voiding plants. So some salvinia and I've already added
a little bit of dwarf sag here as well. I had a couple of sprigs left from a
previous build so I just put that in here. I'm not sure how well it's going to
go. It did dry out a little bit but it should recover hopefully.
Now the part everyone's been waiting for. I'm going to add the crabs.
So it's been 24 hours since I built the tank. Normally I suggest waiting at least
a month, two months or three months. The longer is
always better. However most of this stuff has come out
of a build I just pulled apart or broke down about three days ago so I'm
going to be reusing a lot of it. It's all got beneficial bacteria.
It's covered in springtails already so it's essentially bioactive from the very
start. I don't need to wait for the tank to
cycle and I don't need to wait for the ecosystem to establish.
It's already ready to go. However if you're doing this from scratch with all
new stuff, I highly suggest waiting at least a
month. Things will grow in nicely and you can add your crabs
and have a lot better result in the end. So these crabs are from my previous build.
You can check out some of the videos from this little colony or cast of crabs.
They're red devil crabs. I've got quite a few adults but I'm
also going to be adding the entire generation of babies from the previous
tank. If you plan on breeding these crabs and
you want the best survival rate, I highly suggest
not adding babies into the tank. However I'm going to be letting natural
selection run its course. I don't need any more crabs. I've got
hundreds of them. I do sell them locally. I don't sell them
online because they have terrible shipping survival rates so
before you ask, no I can't sell you any crabs. I'd love to
however being in Europe I'm probably not going to be able to sell it to a lot of
you guys from the United States and the shipping rates are just really
bad for survival so I'd rather not have any crabs die anyway.
So these are all the babies from the previous tank. There's quite a lot there.
I didn't count them but roughly there's probably about 40 or
so there, maybe 50. I'm just going to drop them straight back
into the tank. They'll find all the nooks and crannies
and places to hide. Generally they'll hide in up under the water section and
they'll semi-colonize some of the clay balls at
the front. Otherwise they'll hide in amongst everything.
This tank's been set up for about a month now, maybe a little bit longer
and there's still a lot of babies getting around so they're doing very
well to avoid the adults. There will be some cannibalism as you would have saw
in the introduction. That little guy did escape. He did lose
a leg but he escaped and this kind of thing happens.
It's just part of the ecosystem. The crabs are known to be cannibalistic
but if you want to keep as many alive as you can definitely separate them.
Make a little environment for those guys and you can watch them grow up.
As I sell the adults out of this tank the population of adults
generally doesn't stay too high so it's constantly rotating so by the time these
crabs get a little bit bigger quite a few of the adults will be moved
on to new homes. So I don't really have any issues with the population in this
tank being too high. However as I always say in my other
videos if you're just starting out for a tank about this size I suggest
one male two females. You could go a bit more
theoretically by all the statistics you can go six crabs
but for a better success rate for breeding I'd just start with three.
They'll have a lot of space to move in move around and then have lots of babies
in the tank and you'll have a bit more space for
them to grow up without having to build a new tank straight away.
The final thing I'll mention is make sure you have a tank lid. I know I don't
show a lid in the video in this the introduction or anything but I do
have a full glass lid that goes over the top of the tank.
I just don't use it for filming because it causes a lot of reflections and it
just makes a lot of issues with the editing process so definitely make sure
you have a lid. Non-negotiable the crabs will escape so
a lid is important. The other thing that always comes up is
a heater. I have a heat mat for this tank and it sits between
both of the tanks that are side by side. I have about a one centimeter gap
and the heater sits in that gap nicely. It works really well it's only a 14 watt
heater and I have it on the lowest setting.
You can use an aquarium heater in the water for this as well to heat your tank
though I do prefer heat mats. They allow you to make a tank easier without having
a big ugly heater in the way. Anyway I hope you enjoyed that video if
you have don't forget to like and subscribe.
As always thanks for watching and I'll leave you with a little bit of
cinematic footage of how this tank looks and how the crabs have been doing.
Thanks everyone, see you next time.
