I Made a Jungle Terrarium For a Tiny Frog, Here’s How!

Mini World Craft
6 followers
AI Generated·May contain errors
In this video I'm going to make a lush planted ecosystem for a tiny adorable tree frog.
Be sure to stick around to the end it's going to be a good one.
Here's the glass tank that I'll be using. I built it myself and it measures 45 by 30 by 60.
Shout out to Troy Goldberg as I followed his tutorial to build this Eurostar Bavarian.
I'll put a link below so you can check it out.
As regular viewers may know I have had this tank set up before but it's been a few years
and I've learned a lot since then so I think it's about time for a rescape.
I thought I'd save you the hassle of watching me take it down and clean it all up.
The tank has got two sliding doors with a vent along the top
and another vent along the bottom for good airflow.
To get started I'm going to remove the glass doors and get to work on the background.
What I'm going to use is some compressed cork panels.
They're relatively inexpensive and not too hard to get hold of.
I've never used them before but I think they have the potential of looking really good.
I've already cut down the back panel so now I'm going to use a ruler to measure out the sides.
I'm now placing it on the floor marking out the length and cutting it down.
I'll leave links to all the materials I used for this build in the description and in the pinned
comment. When it comes to the background in a vivarium like this one I always like it to be
on the darker side as I think it looks more natural. Obviously they'll be sitting higher
on the glass but they all fit in perfectly. Now I'm going to go ahead and secure them in
place with some silicone. It's important to use 100% silicone or silicone that's
advertised as fish or aquarium safe. With a generous amount of silicone on the glass I can
go ahead and place in the cork panel and press it down into place. I'm placing on some heavy objects
and leaving it for about an hour or so. The silicone does take 24 hours to cure but after
an hour it's dried enough that I can move on to the next side. I'm going to repeat the same process
until all three panels are fitted in place. It's the next day and the silicone is fully
cured so let's start talking about the hardscape. I've got this absolutely amazing piece of wood
that I got from my local fish shop. I'm placing in a plastic tub which is roughly how high the
substrate will go up to and then getting a feel of how the wood looks in the tank.
I don't know about you but I really feel like it resembles an old ancient tree so that's the look
I'm going to go for. Now I know roughly where the wood is going to go I want to make the background
a little less flat and boring. I've cut up some leftover cork panels and I'm going to use them
to add a little bit more depth and interest to the hardscape. For now I'm temporarily attaching
them in place with some toothpicks just to get a general idea of where I want them to go.
Now I'm happy with their placement let's get them locked down into place.
What I'll be using is this Gorilla Glue. It forms an extremely strong bond and once dry
it's completely safe for live plants and animals. A light misting of water helps it cure and it does
expand so you don't actually need to apply too much. With the pieces in I'm going to place on
some heavy rocks and then let it cure for a couple hours. I'll save you some time and get on with
gluing the rest of the panels off camera. With everything glued in place it's time to make the
background look a bit more natural. I've got a drill with a wire brush on the end to do this.
I'm tearing up the cork panel to give it more depth texture and interest. You can do this by
hand with a wire brush some pliers and a knife but it does take a lot more time. I'm making sure
to go around the edges of the pieces I glued on and make them naturally taper onto the background.
Once you're done they shouldn't look like separate pieces that have been glued on.
Before cleaning up the tank and taking it back inside I'm going to collect up some of the cork
panel shavings as they'll come in handy later. Here's the cork panels all carved down and I'm
really happy with how it looks. It certainly doesn't have to be perfect as a lot of it's
going to be covered up with plants and a hardscape anyway. I've got a few small pieces of wood which
I want to attach to the cork bark. These will add more detail and provide a place to mount plants
onto later on. After experimenting with their placement I'm going to glue them in place with
the super glue and tissue method. I'm going to add multiple points of contact just to make sure
it's nice and strong and not going to go anywhere. Now I'll glue this one on the right side and a few
other pieces around the tank. With these pieces securely locked down I want to take the hardscape
to another level. I want to create the look of roots growing down over all the sides of the
background. I'm not completely sure how it's going to turn out but I think it has the potential of
looking good especially when the tank is planted. The wood I'm using to create this look is spiderwood
branches. I'm really trying to make them intertwine with the hardscape as best as possible to try and
create a natural looking ecosystem. A couple hours have passed and I've managed to get the left side
and the back done. Despite it being an extremely tedious process I'm absolutely loving how it's
looking. Now although the branches look like they're single pieces they're actually made up
of multiple smaller ones. Obviously it would be much easier if they were single branches but
sometimes you've got to work with what you've got. I'm constantly trimming and gluing the branches to
make them naturally lead into one another. It is time consuming but I'm hoping the end result
will be worth it. Here's all the branches in and it's safe to say I'm really happy that I went ahead
with this idea. What do you think? Is it too much or do you think it will add to the natural look of the
tank? Let me know in the comments. One thing that's certainly not looking natural is all the glue
joints between the wood and the background. To cover up all the glue marks I'm going to use some
liquid type super glue and some of the shavings that I collected from the background earlier.
I'm simply applying the glue on the area I want to cover up and then sprinkling on some shavings.
After brushing off the excess you can see that it creates a seamless and natural looking joint.
I'll go ahead and repeat the same process until all the glue marks are covered up.
I've taken the tank back outside and I'm giving it a really good spray down.
After draining out the water and bringing it back inside it's now time to get it in
place on the rack. It's going to sit here in between the praying mantis tank and my dark frog
vivarium. With it on the rack it's finally time to move on with the build and get the drainage
layer in. What I'll be using is this coarse filter foam. I'm taking some measurements and then
cutting the foam down to size. The benefit of using this for the drainage layer is that it's
extremely light in comparison to rocks and stones. If I ever needed to move the tank using this makes
it much easier. In a setup like this it's extremely important that there's a way to drain water out
from the drainage layer. This here is a quick and easy workaround to drilling a hole in the tank.
At the bottom I've cut slots which will allow water to flow into it. I'll then place it in the
corner of the tank and whenever I want to drain out the water I'll place in some airline tubing
and siphon it out. I've got the same setup on my dark frog tank which is just past three years old
and it's still working great. I do recommend placing a cork on the top to stop things like
substrate and plant matter blocking up the hole. Now the drainage layer is complete I can place
in the substrate barrier. I'm using some window screen mesh but some weed blocker fabric also
works well. This layer will help prevent the substrate from getting down into the drainage
layer. Next up I'm going to add a layer of crushed charcoal. Now I don't usually do this as I have
the charcoal in my substrate mix but I thought for this build I'll add it anyway. The purpose
of charcoal in an ecosystem like this one is to remove impurities from the water. Next up is the
substrate. This is my terrarium soil mix which I use for pretty much all my builds. I'll put the
components up on screen now and I'll have links in the description as well. It holds moisture,
is resistant to compression, provides nutrients for the plants and it's well draining. I'm pouring
in a generous amount and then gently compressing it down into place with my hand. With the substrate
in I can now place in the main hardscape element. I'm using a small piece of wood to help prop it up
which also looks like a root at the base. Now it's nice and stable I'm going to add some more
substrate in behind it. After adding a few final touches here's the complete hardscape.
I'm extremely happy with how it's turned out and I think it makes a great skeleton that can be
brought to life with plants. Talking about plants let's get the planting started with these bromeliads.
These are perfect for a tree frog setup as the frogs love to take shelter in the leaves.
These plants are epithites so they don't need to be planted in the substrate and they can simply
be mounted on the wood. I'm wedging the first one in behind the tree and then I'm going to mount
another on the right side. To hold it in place I'm firstly going to apply some gel type super glue.
Once dry it can hold the plant up but it certainly won't be strong enough to hold it once it's full
of water. To ensure it doesn't fall off I'm also going to wrap it with some thread. With time it'll
grow anchoring roots which will hold it in place. Now the bromeliads are in let's move on to some
climbing plants. This is a long cutting of Macgravia centennici. I'm using some scissors
to trim it up into multiple cuttings which I'll plant throughout the tank. As I said this is a
climbing plant so I'm making sure to plant it in areas where it has room to climb up the background.
I'm using some stainless steel staples to pin the plant down onto the cork panel.
Next I'm going to add some sphagnum moss underneath it which will really help it root and start
growing. These stem cuttings will send out new shoots around the top leaves which will grow up
the background. This can take some time especially when plants are acclimating to a new setup.
If you're enjoying this video so far be sure to give it a like as it does really help out.
Next up I've got another Macgravia species which I propagated on this tree fern panel.
Instead of pulling it off the panel and potentially damaging the plant I'm just going to plant it as
it is. I think these smaller Macgravia cuttings will look really good growing up the base of the
wood. I'm hoping they'll slowly grow and creep up the base and look like they do in my praying
mantis terrarium. I really think this look will add a natural feel into the tank. Talking about
this tank some of the plants are getting a bit overgrown so I'm going to take some cuttings and
put them to use. This climbing plant is Solanum Ecuador and it has these stunning brown tinted
leaves. When using the staples to pin the plants down I'm making sure to leave some wiggle room
as the last thing you want is to damage the stems. This next plant to go in is one of my favourites.
This is Philodendron Vericosum. It's got these amazing green velvet leaves which do grow to a
relatively good size. Once established this plant will be one of the main features of this tank.
I'm keeping the rhizome above the substrate and then covering the roots with some sphagnum moss.
After giving the tank a good spray down I'm going to plant this Syngonium.
It's not looking in the best shape but I'm hoping it'll recover and grow well in the tank.
I'm planting the rhizome on some sphagnum moss and then using toothpicks to pin it down into place.
Up next is another Philodendron species but this one will stay much smaller than the Vericosum.
As I'm sure you can tell I'm trying to use a wide variety of plants to make this tank look like a
true natural ecosystem. In my opinion a mix of leaf shape, size, texture and colour is always
going to add to the natural look of a tank. This here is a small leafed climbing plant known as
Oak Leaf Creeping Fig. I think it will add some really nice detail growing on the ancient looking
tree. When planting plants away from the substrate it's always a good idea to provide something that
will hold moisture and help them grow. I always find that a small patch of sphagnum moss works
great. Planting a tank like this does take a while so I do like to give it a light spray down every
now and then. I think some moss and plants growing up on top of this wooden branch will look really
good. Same as before I'm wedging in some sphagnum moss followed by a few cuttings of Oak Leaf
Creeping Fig. Now this next planting method is a bit of an experiment so I'm really not sure if
it's going to work. I've wrapped the base of this ficus in some sphagnum moss and I'm going to wedge
it in the top of the tank. I'm hoping this will help jump start the plants growing in and filling
out the background. Before adding any moss to the tank I firstly want to add some leaf litter.
I'm starting by breaking up some Indian Almond leaves. On top of the Indian Almond leaves I'm
going to place in these mangrove leaves. I'm not breaking these ones up as I want them to look nice
and natural. These leaves not only make the tank look extremely natural but they also play a key
role for the microfauna. Things like springtails and other small bugs will primarily use these
leaves as their home and a source of food. I really want the base of the tank to look like a forest
floor so I'm going to go ahead and add some more detail. I'm using some thread to wrap some sphagnum
moss around this small piece of driftwood. Now I'm going to take some Christmas moss and use some more
thread to wrap it down onto the sphagnum. This is an aquatic species of moss that grows great in a
setup like this. However it really doesn't like to dry out so adding the sphagnum moss really helps
it retain moisture. I'll go ahead and cover some more pieces of driftwood using the same method.
Now I can freely place them at the bottom of the tank to add a nice pop of green amongst
the leaf litter. I'm going to place some more Christmas moss in a few select areas around the
tank. This is mainly in areas where it can sit on top of some sphagnum moss and is less likely to
dry out. With time as the tank establishes it will slowly creep and grow over the hardscape and
background. The tank is now fully planted and I'm absolutely loving how it looks. Before I can leave
it and let it establish there's a few more things that I need to do first. Now I'm going to install
the misting system. I've created this triple-headed misting output myself with some push fittings.
It's not too difficult at all and much cheaper than buying it ready-made. Along with everything
else I'll have a link to the push fittings in the description. It's fully adjustable to point in any
direction I want and it attaches to the top of the glass with some suction cups. Instead of having to
drill a hole in the glass I've simply made a small hole in the mesh vent which I'll sandwich between
with some push fittings. I can then connect the other end which leads to a pump that powers the
misting system for both of these tanks. I've set the timer up to turn on twice a day for 15 seconds.
Now you don't actually need a misting system and there's nothing wrong with doing it with a spray
bottle but I already had it set up so I thought I might as well put it to use. I'm not putting the
frog in yet but some creatures that can go in now are the springtails. In a setup like this one
springtails truly are essential. These tiny bugs will eat things like mold and decaying matter.
This food is then processed and pooped out in the form of fertilizer that the plants can use
to grow. They'll also completely take care of the frog poop so I actually never need to clean this
tank. To introduce them to this ecosystem I'm gently pulling back the leaf litter and pouring
them underneath. This is where they'll spend the majority of their time. Now before introducing
Grogu the tree frog to his new home I'm going to put the sliding doors back on and let this
ecosystem grow in and establish for a couple months. Four months have passed and this vivarium
has grown into a lush slice of nature. For the most part it's been absolutely thriving and I
think the plants truly speak for themselves. I have made a few additions which I'll talk about shortly.
Unfortunately the syngonium I planted at the base didn't make it but I decided to replace
it with this stunning peperomia. I'm almost glad that this happened as I absolutely love how this
plant looks growing at the base of the tank. Another addition is this fine leafed green plant
known as leliopsis. I only planted a couple patches and it sent out runners which are slowly creeping
around the tank. My favorite new addition has got to be this begonia. Its leaves are stunning and
it does great in low light making it perfect for the shaded areas of this tank. What other plants
would you add as I'm open to suggestions? Let me know in the comments. Although it's hard to see
the macgravia cuttings are slowly creeping up the ancient tree. An honorable mention has got to be
the new growth on this macgravia umbellata red. I can't wait to see it climb all the way to the
top of the background. Now I can't talk about plant growth without taking a look at the absolutely
breathtaking philodendron vericosa. This plant is truly the centerpiece of the tank and I couldn't
be happier with how it's doing. As for the Christmas moss planted around the tank it's doing just as
well as I hoped it would. It's growing nice and compact and slowly spreading over the hardscape.
Not every plant has been thriving in this setup. The experimental planting of the ficus didn't
seem to work out at first but it seems like there's some new growth coming so I've got my
fingers crossed. That's why I love setups like this as you can try new things and find out what works.
Without further ado it's finally time to introduce Grogu to his new tank.
He's a male hourglass tree frog and I've had him for about three and a half years.
Compared to other species of tree frogs he's absolutely tiny so this tank will be a mansion
for him. I am thinking about finding him a lady friend and even trying to get them to breed so we
can have even more tiny adorable frogs. Let me know if this is something you'll be interested
in seeing on the channel. He really doesn't want to get off the leaf and he's just sitting there
admiring this ecosystem that he can call home. Instead of forcing him off I'm going to place
the leaf at the base of the tank and let him start exploring in his own time. As for his diet I'll be
feeding him a mix of fruit flies and small crickets. I should mention that I have set up a
low-powered UVB light that shines through the mesh at the top. Now I'm going to get the sliding doors
back on just in time for the rain. If you've got time I'd love to hear your opinions on this
ecosystem in the comments below. Whether that's things you'll do differently or plants your dad
I'm all ears. I really appreciate you making it to the end of this video. Don't forget to like
and subscribe as it really helps out and as always thank you for watching.
