Using 3D Printers To Build A Car Out Of Carbon Fiber | Part 3 | The Legacy (15)

Tuning Pro
54 followers
#GJWcars #GJWauto #Customizingcar #tuningcar #howto #DIY #CarCustomization #upgradecars #editcar #wrapping #bodybuilding #bodycar
AI Generated·May contain errors
Welcome back to the Legacy Electric Z project. Today we're building doors and rocker panels.
Damn so sturdy. Okay we're going to run you through a little bit of how I made this plug
because this is one of the only panels I'm kind of hand shaping. We used a piece of half inch
plywood. Just cut it down to about the width that we were looking for. Match up with the width of
the quarter panel and then we just screwed into the rocker panel from underneath and it's crazy
how sturdy it is just with wood screws. Kind of insane. I took some pieces of you know quarter
inch thick plastic sheet that we had back there and I cut it into four little boxes.
I was wondering what those were. Yeah and then I ground down the back of it
because if you look at the renders there's like a nice little detail where these are all cut out
but for the mold I need them like filled in like this. Dang it's dirty.
So you know you've been getting work done. So yeah just glued those down there. Did a little bit of
mud work. Foamed this. Mudded that transition. Then up here in the front we want to make sure that all
the air that's the turbulent air that's getting in the wheel well has a nice clean path out.
So I worked took a bunch of time and like made sure that our new panel can kind of just hug
this upper I guess it's kind of like a frame rail not really but this upper rail and the battery
support area. So everything is blended in really nicely. We had to cut this back just a bit as well
to make sure that the tires had clearance to turn. Took a bunch of measurements on the other car that
actually has the wheels at the correct offset because our wheels on the SEMA car are like
three inches or three and a half inches wider set out than this wheel. So yeah we should have we
should have plenty of clearance to turn. It's tight but it should be completely fine and it
it'll never hit unless we have the car jacked up and the wheels completely turned
and it would probably drop down onto this but not a problem. But this is obviously the inner section
of the fender so our other fender panel will sit on top of this. Maybe a little airfoil kind of
shape that will connect both of them and then not for SEMA but after SEMA we will we'll do like a
little 3D printed head that'll hold a camera so then we can run our side view mirrors are going
to be little cameras. We'll look through the little vent on the fender so that's most of how
we made this plug. The drivers well both doors were 3D printed in sections similar to all the
other panels and then bonded on. The only tricky part on that was making sure that it matched
where our quarters were perfectly and then matched the front of this so it kind of had to all happen
at the same time. Set the quarters where they needed to be, bonded the doors, finished the
quarters, then finished work on the door and rocker inner fender piece all at the same time.
How many hours would you say you have invested into the doors and rocker?
I think it was like four straight days of mudding at 10 hours probably a day at least so
I'd say 40, 40, 45 maybe. Turning into a mud work hobbit. I hate it, I hate it. It's fun if it's a
small project when it's a project it's like days and days and days and it's like just filing down
the doors skimming it again filing down oh my god. All right now that the quarter panels are
kind of complete we're gonna go ahead and move on to the doors and the rockers. If you were
watching closely when we did the mud work on the quarter panels we actually mounted these
rocker panels. This is just a half inch piece of wood that I actually added a little
piece to up here because it needs to dive in. I did not 3d print this piece because I knew I had
to kind of shape it myself because the actual turning radius of these wheels those are actually
sticking out a little farther but I measured everything like that this should barely clear.
This is going to be easy enough for me to shape out of foam so we're gonna go ahead and foam this
but before I do that we're going to jump and bond on the final door. I did glue up all six
eight panels and bonded the passenger door on already so we're gonna go ahead and do a little
bit of trimming on the back side of this thing see it's a little crazy and then bond it on here.
We're going to use the slower epoxy but what we're really looking to do is make sure the
actual profile this back edge of the door sits flush with the quarter panel.
You can tell this needs to be trimmed in the back here and I did actually put
the latch in here and the rubber. I'm gonna have both so I made sure that the latch was
set all the way in as far as you can go with the rubber still being here and having the top
this little bit line up perfectly so the door is exactly where it's going to be
when it's mounted on the car with the new gasket. The new gasket might push it a little bit
but with the latch we should be able to get it to close correctly so
that's where the door is going to be make sure that this door fits perfectly
bond it on there and then we'll uh foam the rocker panels.
All right it's the next day this door has completely dried took all the screws and stuff out
so we're ready to rock and roll the door. I'm gonna do all the mud work at the same time though so I
want to foam the rocker panel you foam like this little section right here and this nose
you might need to cut some of this way but before I do that I want to glue these little vents.
The fender has four vents the quarter panel says four vent and then these four little vents in here
continue that same design language. I just took a piece of quarter inch plastic sheet that I had
and I cut it down put a little taper on one side and they're all going to sit in line here
and then once the uh once the mold is made this will be cut in the carpet piece right in front
of each one so they're little vents that scoop air out. It should create like a little curtain
uh this is taken from like formula one style
ground effect stuff we've done any cfd testing but it's a cool design I would like to do some
actual wind tunnel testing with this thing once we have it done just because the hose
scoop should be very aerodynamic something like that pretty cool shoot a comment mentioning uh
any wind tunnels around everybody I'd like to actually talk to somebody and maybe get
something set up for maybe end of the year
but all right I'm gonna get to epoxying these little four guys down here and I'll make the
probably cardboard trough that I'm gonna eventually throw the foam
so yeah thank you to everybody that bought shirts from us and stickers and all the merch
um this is the best way to support us you know I wrote this demo that's possible
but yeah thank you everybody that has supported us through all this
go to instagram.com you can get all our six shirts we actually have not added these on yet
these will be added on to the website once
in the triple xo these will be added onto the website once this is live so they're on there now
special edition three color shirt the banditos call um but yeah albert cleaned up everything
in here so it's not as chaotic as last time he's on here but we are hand packing all the orders
again into garage.com
I don't know if that was a b-roll clip or
yeah so we have a very solid door um we made sure to make the door a little bit more
solid than the rest of the panels sacrificing a little bit of weight to make sure that like
something that you hit all the time it's not going to touch the quarter panel all the time
so the quarter panel is just four sheets of 3k which is slightly flexible so I mean if you punch
it it'll just spring back um but the door panel the doors are going to touch all the time you
know getting in and out so I want to make sure they feel sturdy especially after we made my uh
the f-22 powered z um I keep wanting to call it the carbon z but they're both carbon down so
we have two yeah so we made those doors and they're it's just a full race car it doesn't
have an interior door so it's just super flexible and it's just a little annoying
every time somebody new gets in the car I gotta be like well you gotta open it like this
this is gonna be any person can walk up hit the little there's gonna be a little button under
here because we're not obviously we shave we don't have any door door handles so there's gonna
be a little door popper electronic door popper in the door there'll be a little hidden button under
here so you won't ever really see it but it does stick up a little bit just for you to be able to
feel it actually I'll grab that one this little dude it's gonna sit you know somewhere probably
right about there I'm just gonna drill a hole I mean I could technically do it right now
we'll do it for you real quick give us a second why not this here I think of like we're going up
yeah I want it on the right side about there so we're gonna put something in my mouth sure
all right so there we go we got that's our door handles technically
nice little tactile aluminum switch it's nice very batmobile like yeah exactly
ash yeah so this is this is our door it's nice and sturdy not really flexible at all
we did very rigid yeah we hit it with a piece of we did three layers of 3k and we hit it with a
type stuff and then backed it by a piece of 12k so nice should have some impact resistance and
then we are bonding it to the metal door we did a bunch of prep work the door needs to be primed
sanded and satin blacked on the back section of it the nice thing about this is we can keep the
big impact resistant bar in the door this is a 280z door 280z have this big bar 240s
they only have like a little c channel of metal you could just punch it it would dent it was
not safe but so since we have a 280 we have this we have safer doors and it's also a better latch
mechanism the 240z latch is garbage it's the worst it's like a circular thing that spins and clicks
they get cruddy and the spring in them lets loose it's a pain some of the plus sides of
having a 280 show even though 240s are cooler but whatever everyone knows everyone knows i'm
not saying anything crazy everyone that has a 280 wants 240 parts on it it's just the same thing
yeah so nice solid doors we need to test fit after we get the doors painted we need to
bond on the quarter panels test fit the door to the quarter make sure that's all great
the latch lines up and then we will test fit the fender and then set the door outer skin
and bond that on to make sure everything is good like gap wise we don't want to bond it on slightly
off to the back and then have it like touch the quarter panel every time you close the door so
fitment of the doors should be last so we'll do that once we get to that but let's go to
the other side and we'll show you the rocker so we got a nice rocker should be aerodynamic
i still have to cut this uh this little channel here because that's where like the seam of the
frame rail meets the other frame rail so it should go in like another half inch this way but
it's literally just sitting on here it fits so tight like no bolts on it it's just chill
it's that good fitment but it made me kind of nervous because we know how
you like to actually bump into stuff i'll drop it but yeah i mean this came out really nice
then we use stabilized carbon where we could none of this is stabilized but here back
the fender sits over here so you really see a lot of this so i wanted to make sure that that
weave looked very straight and true we keep talking about it everyone's like shut up about
the stabilized car after seeing how you cut it up and manage with it yeah it definitely seems
like it's great so this will sit this bonds uh well i think we're gonna actually have these
bolts on just because it might be easier for trailer and stuff like that so i'm gonna drill
holes run rivnuts um and then this little edge will be cut off we'll probably have bolts this
way because if we put bolts in here one we don't have very much space but we'll also run into
uh the bottom of the door will touch the bolt heads so we're going to run some shallow bolts
through there or we bond them on they could be bonded on permanently honestly but i don't know
i keep going back and forth so i haven't drilled any holes yet we'll see what happens if you did
we could i'd have to get more hardware i just got a ton of hardware that's button head
so button head's not bad either it looks looks nice it's okay we trimmed out these little
spat things i don't really know what they're called ash saying that they designed these off
of like looking at the under tray on a bunch of like the newer generation formula one cars so
in theory it should work but until you put anything in a wind tunnel you're not gonna
know if it's working or not but more importantly this does continue the uh the kind of four
slices that we had in the fender and we also have in the quarter panel and we have a little
we have four slices in a little hood dash piece that i just made last night actually
but so it's got the same design language throughout the whole car kind of all flows
nice little detail it looks good everything came out great all of this weirdness this
all gonna get cut from here up i was gonna ask this edge over that all gets cut i was like i
don't know i didn't want to ask but now that you mentioned it what is this yeah what is that yeah
so this this body line right here up gets cut off and then this edge over will get cut off as well
but for right now just sat and cleared them because i haven't decided if i'm bonding it
on or whatever but this makes it easy to kind of just mock up if this was completely cut off
it would just drop down over this side so yeah but it's very cool seeing the rocker panels
we have all these panels but none of them are actually on the car as a unit yeah having two
weeks until sima and then seeing this is what the car looks like it's like or we're gonna get there
you have to believe in the process yeah i mean a lot of mechanical stuff is done like we have
full suspension we have full brakes technotoy tuning hooked us up with their rear big big
brake kit which we didn't show in the other kit got a little spacer here too
yeah the washers on in the wheel video yeah exactly i was like oh hell those washers were
sketchy but yeah so we got hub centric spacers for the front and rear yeah so i mean a lot of
mechanical stuff it's a lot of small tedious wiring but with am's uh pre-made harness it's
only like i have to wire the bms and then change two connectors and everything else is pretty much
done so what we do with the wire the door poppers wire in little accessories yeah just a little
thing like the headlights taillights blinkers window motors yeah door actuators done in a day
and a half yeah you know it's a lot of those day and a half things and we have and then 14 days
along the way on the road i'm gonna be working on it while it's getting trailered to sima just like
a hideaway in it feel like the goonies it's a booty trap but okay well this is uh
gonna wrap it up for today's video we'll see you soon in vegas
