Testing the LAVAL RAM-JET Shotgun Slug

Ballistic Lab
1 follower
3 Video Views·Jun 12, 2026
Today we have a design by Heinz and Saar - a very unusual design that uses a ram-jet design. This was a very difficult project since we were trying to get a theory to work with a very limited number of projectiles. The velocity had to be sub-sonic - which isn't easy to pull off since we were bleeding off some of the pressure through an orifice in the gas seal.
AI Generated·May contain errors
Hello everyone, this is Jeff of TOW Flare Mouse. We have an interesting project today
that is more like rocketry and less like 12-gauge slugs, but this is a 12-gauge slug.
And because this is a pretty complicated project, it's taken me a long time to finally get to the
test. The projectiles were constructed by Saar of Israel, but the design comes from Germany
by another man called Heinz. The general idea is that we have a subsonic projectile
that is very long but very nose-heavy. Now this part, to my understanding, is the gas seal.
It has a very small hole which allows the propellant gases to blast through there and
kind of preheat the chamber inside that projectile. And then the air entering through the nose
is heated up, expands, and is supposed to cause it to accelerate. So yeah, it's a little bit
complicated to make this all happen on my end. Now the projectile has a heavy brass nose,
and the body is made out of magnesium. And magnesium was chosen due to its low density,
much lower than that of even aluminum. And that allows us to move the center of gravity way out
towards the nose. Now these projectiles are quite long, measuring around 1 and 13 sixteenths of an
inch, or 46 millimeters to keep it simple. Now we'll be using a very short X-12X gas seal that
has a tiny little pinhole pierced through the center of it. And the projectile itself will be
riding inside a two-piece discarding sabot. And as you can see, there's not a lot of extra room
inside that three-inch 12-gauge shell. Now in case the hot gases from the powder alone is not
enough to heat up that chamber, I've made some little kind of heat generators here. And if needed,
these can be inserted into the cavity there to heat it up even more. And of course, coming up
with something that burnt not too fast and not too slow was a task in itself. And in order to
get the airflow going through the center of that, these have to be shot at a subsonic velocity. So
I've got to try to get these things traveling around a thousand feet per second for that to
happen. At supersonic speeds, we would have a bow shock wave at the nose that would prevent any
airflow from traveling through the center. Well, it's time to get on with the test and
see how these things perform. For today's test, we'll be using the Mossberg 500 Danny's old
shotgun, and it is fit with a smoothbore for the first test. The gun is mounted in a rest
with a remote trigger designed by Brian from Cincinnati. Now the shells have not been roll
crimped. This is so I can make field modifications if needed, like remove that little heat generator,
add it or whatever. Now we only have six of these. So what I'm trying to do here is I'm
going to shoot into the dummy that has a Kevlar vest, and I'm hoping to be able to capture
a couple of them intact so they can be reused. So instead of just six tests,
maybe we can get like seven or eight. And the target is set up at 20 yards,
and I'm just hoping these will be accurate enough to hit it. Let's see how it does.
Okay, here we go. Everything's safe in the background. Let's do it. Oh boy. Yeah,
I was aiming directly at that center mass there. Everything's safe in the background.
Let's do it. Oh boy. Now this test, again, we're using a smoothbore and no heat generator
inserted into it. And unfortunately, we just did not obtain any kind of stability.
The accuracy was really bad because of that too. Now the only good news here is we did achieve the
velocity we're looking for. It was 990 feet per second, so definitely subsonic. So I'm actually
kind of happy that I got my recipe right for the test. Next we'll use the heat generator and also
the full rifled barrel. Let's see if they do. Let's hit it. Looks like a hit, I think.
On this test, we can clearly see that the heat generator ignited with that big black cloud of
smoke, and it also kind of smelled like fireworks. Now unfortunately, on this shot, the nose and the
tail assembly came apart, and both of them actually hit the dummy. One hit him in the
kind of left shoulder and the other one, the body of it, hit the top of the right shoulder. Our left,
but the right shoulder. And unfortunately, that can sometimes happen just from inertia. Now the
velocity of that one was 998 feet per second, right in the envelope that we were looking for,
but sometimes physics comes in and rears its ugly head. Okay, we're going to try another one. Aim a
little bit lower. Maybe this one will function. There we go. There we go. Now this one was a
1048 feet per second, and it held together, and looks like it was a pretty decent shot. Hit kind
of low, but I did aim a little bit low on that shot. But it seemed to be flying pretty stable,
so that's a good sign. Now remember, one of my goals was to catch it in the Kevlar vest, and
we were able to do that. This is what it looks like. The nose is a little bit beat up looking,
and it is packed full of cloth and Kevlar and all kinds of stuff. The heat generator
is completely burned out, and it smells again like fireworks inside, and you can see how much
cloth and other material is stuck in the nose there. So that one we can reuse. Now we'll be
able to load this into an extra shell that I had prepared, and we'll try it again with new
SABOs and everything else. Let's see how that does. Okay, this is the one we just shot and
recovered, and I reloaded it, and let's give it another shot. Let's see. Here we go. Change the
camera angle a little bit. It's like a hit. I must have been so hyper-focused on this project
that my high-speed camera shots are just terrible today. I apologize for that. But I wanted to get
a shot of it leaving the barrel. We can see a big fireball from the heat generator and all the black
smoke, and we can kind of see that the projectile was more or less stable flying and fortunately
accurate enough to hit that big Kevlar vest. They're not accurate enough to hit anything
smaller than that, it looks like. And for the record, that one was traveling at 1027 feet per
second. Believe it or not, I was able to recover that one. It's pretty hot. A lot hotter than a...
Yeah, look how much fabric it chewed up there. I'm surprised. Still a little banged up and not
terrible. We can use that one again if we need to. It smells like fireworks. Okay, let's try another
one. This one has not been shot before. All right, here we go. Okay. Okay, that one looked pretty
accurate. Now this one was traveling at 1102 feet per second, which is about 0.98 mach and not
super stable. It was kind of corkscrewing in there, but it kind of flew in there nose first.
But it more or less hit where I was aiming. So that was probably the best flight so far.
And I was able to recover that one. I didn't find it at the time. I just found it like a day later
after I tested these, but very similar to the damage of that other one we recovered. Since I
was so confident with that last shot, as far as the accuracy goes, I decided to move the target
back to 26 yards from 20 yards, which is now at about 23.7 meters. Here we go. And that looks like
a miss. Here we go. Again, not the most beautiful, stable flying projectile we've ever seen,
but you know what? It actually hit him in the arm, so we'll count that as a hit, right?
In fact, we'd be calling him lefty now. Look at all that debris from that heat generator.
And then there was like a paper patch wrapped around the slug. I didn't mention that earlier.
Okay, this is our last one. Yay! It's not been a very satisfying test, I have to say that.
We'll talk about that a little later. Still at 26 yards. Let's see if we can finally hit it.
Hit it! Uh-oh. We got some kind of a failure there. On this test, we had what is called a
squib. The primer went off. Looks like our heat generator lit up fine, but no powder ignition.
I'm kind of surprised we didn't have more of these problems. Trying to get these slugs down to,
you know, a thousand feet per second can be a little bit challenging. Now, the slug itself
managed to travel about six inches down the barrel and was very stuck in there. I had to
knock it out with a steel ramrod, but fortunately I was able to reload it and give it another try.
Maybe, maybe we can hit this thing at 26 yards. Here we go. There we go. That was a pretty good one.
Here we go. There we go. On this final shot, it seemed to behave pretty well. A little bit of a
speed wobble to it, but the accuracy was pretty decent. It hit the top of the vest. It actually
went through the vest. It cut through that Kevlar. Now, for me, this was a very, very frustrating
test. I wanted to do it right, and I think I did everything correctly on my end. You know,
getting the velocities right, loading them right, getting the SABOs the right fit, and all that
stuff, but to be completely honest, I don't know if this design did what it was supposed to do,
where it was supposed to accelerate even faster as it goes down range. I don't see any evidence of
that, but I'll tell you what, you never know until you try, and I was hoping we'd see some kind of
magic from these things, but I'm just glad it's over with. Poor Saul and Heinz have been waiting
a long time for me to test these things, and I'm kind of relieved to get it over with, but I was
hoping the results would be a little more stellar. At least the last shot was, it looked like it was
doing really well. It went through the vest. Even at that velocity, that hard brass
sharp nose just cuts through the Kevlar, even at about 1,000 feet per second, and
went out the back there. There you go. Pretty impressive. For a low-velocity subsonic slug,
that's pretty good. Very troublesome, hard to get these things to work, but yeah, not the most
illustrious test we've ever done, but still, it was kind of interesting, and we left on a
high note here with a nice accurate shot.
