Why You Should NEVER FLUSH YOUR TRANSMISSION FLUID!!

Allstar Auto
20 followers
4 Video Views·Oct 20, 2022
Picture this, you drive a 1995 GMC Suburban.
It's 24 years old and has 78,000 original miles.
The trans-fluid looks like this,
but it could look like this.
Do you flush it?
Comment below.
Hello friends, I'm Jimmy and you're watching OneRoad.
In this video, I'm gonna flush my old,
crusty, original transmission fluid
with this brand new cherry red synthetic stuff.
The tranny is a 4L60E.
Let's get into it.
All right, for the transmission fluid,
I'm gonna be using this
Valvoline MaxLife fully synthetic fluid.
This fluid is rated for Dexron 3
and that's exactly what this truck calls for.
I'm also gonna be using this clear vinyl tubing.
It's a 10 foot section with a half inch outer diameter
and a three eighths inch inner diameter.
As for the filter and gasket,
I picked up this Wix unit from my local auto parts store.
Here, you can see the new filter seal
that we actually won't be using.
But if you're wondering what they look like,
well, this is it.
Here's an up close view of the filter.
This 4L60E transmission comes with either
a shallow pan or a deep pan.
In my case, it's a shallow pan
and this is the filter for it.
This kit also includes a rubber gasket.
The first step we're gonna take
is actually flush out the old transmission fluid.
If you look over on the top corner
of the passenger side of the radiator,
you'll see this hard line threaded right into it.
This whole passenger side of the radiator
is actually a transmission cooler.
There, you can see the inlet in the bottom
and the outlet comes out the top.
This truck in particular,
not only has the radiator attached cooler,
but there is also this external cooler.
We could take off the whole front grill of the truck
and drain the fluid from the outlet
of this external transmission cooler.
However, I want this to be as easy as possible,
so we're not gonna do that.
Back to this hard line coming out of the top
of the passenger side of the radiator,
we're gonna go ahead and take this out.
I did spray it beforehand with WD-40,
so cracking this thing loose is no problem.
In order to not have any leaks,
you're gonna have to thread this clear vinyl tubing
into that fitting.
You literally have to apply tons of pressure
and twist it at the same time,
just like you're threading in a bolt.
And before long, it will be threaded in there
nice and tight.
Then this line just runs right down to your catch pan.
This next step is not for the faint of heart.
Matter of fact, this whole process
is not for the faint of heart.
What we have to do here is actually start the vehicle
and let the transmission do the pumping.
What's literally happening right now
is the transmission is pumping all that fluid
through the cooler in the radiator and out this hose.
It's going right into our catch pan,
and we're gonna keep this going
until we start to see bubbles.
Once you see the bubbles, shut the car off immediately.
All right, look at what we got out of this transmission.
So far, this is a little over five quarts.
It started blowing bubbles,
which means there was no fluid left in the transmission pan.
But this stuff looks like mud.
Look how disgusting this is.
Now I'm gonna drain this catch pan into another
because we're gonna have to do this process again.
With the transmission pan being fully empty,
we're gonna pull out our transmission dipstick.
This is also where we're gonna pour in
our brand new fluid.
Since we pumped out about five quarts,
I'm gonna go ahead and pour in four quarts
of brand new fresh fluid.
This should be just enough to let that transmission pump
do its job and pump some more old fluid out
into my catch pan.
And here we go again.
I started the truck.
I waited a few moments for that pump
to pick up that new fluid and begin the pumping process.
This pumps more of that old fluid out of the system.
Again, I'm gonna keep this going
until I start seeing bubbles.
And here you can see the benefit
of using this clear vinyl tubing.
The old fluid has now mostly been pumped out.
As you can see through the tube,
the color is no longer a brown mud, but a respectable red.
Now, I do admit this process, although it's called a flush,
does not get every ounce of the old fluid out.
There's still fluid caught up in that torque converter
and I'm sure in other places within the transmission.
But for the most part, we're pumping out
as much of the old garbage as we can.
All right, with the flush done,
we're gonna go ahead and jack up the truck
and put it up on jack stands.
I'm also gonna chalk off the rear wheels
as well as setting the parking brake.
Here you can see I'm using not only two six-ton jack stands
as my main jack stands,
but I also have two three-ton jack stands backing those up.
Now for the hard part.
Looking up at the transmission pan,
you can see just a few of the 16 total bolts
that we have to take out.
In my case, I'm gonna be using a ratchet,
an extension, and a 13-millimeter socket.
Just start grinding away and get these suckers loose.
On one end of the pan,
you're gonna wanna leave the bolts fully tightened
while you take out all the rest.
The object here is to not let that pan fall.
So we're even gonna leave a bolt on the other side,
loose but in.
As I take these bolts out,
I'll be using this cardboard template.
By doing this, I can ensure that I'm putting
the same bolt back in the same hole
when we're ready to button this thing back up.
All right, so I have most of the bolts removed
except for one up front and a couple in the back.
This pan is ready to be cracked loose.
I'm taking out this last front bolt that was holding it up
while keeping pressure on the pan,
and I'm cracking it open.
The pan is now being held up
by these few loose bolts on the back end.
I also have a drain bucket ready to go.
Keeping pressure on the pan,
remove the last couple of bolts.
All right, all the bolts are out, guys.
This is the scary part.
Keep your head and face out of the way
and try to drop this pan as evenly as possible.
Oh, gosh.
Oh!
Almost!
Gosh, I almost just took a bath in transmission fluid.
Wow, that was close.
What a mess.
It is now time to take out the old filter.
The best way to do this is to simply
just rock it back and forth while pulling down.
It should just pop right out.
Well, here it is, an up-close and personal look
of the 4L60E Sans drain pan.
Well, this next part is definitely not recommended
unless you know what you're doing.
I'm taking my torque wrench
and I'm torquing these bolts down
to eight foot pounds or 96 inch pounds.
Some of them were very loose and some not so much.
The next step is to make sure
that the gasket mating surface is clean and clear
of any sort of debris or dirt.
All right, guys, so I've chosen
to leave in the old filter seal.
I didn't bother trying to remove it
because it is quite a pain in the butt.
So I'm gonna go ahead and tap in my new filter,
which is pre-lubed with just a very,
very small amount of grease.
Now that that's all done,
we can focus our attention on the drain pan.
Looking at this drain pan,
we can see that it's actually not that bad.
We do have some old gasket material
that we will have to remove,
but look at this magnet, guys.
This is precisely why you should at least
be dropping the pan and doing a filter change.
This magnet contains all of your metal shavings
that come off of the transmission
and clutch plates with age.
This is basically metal dust
that has been caught by the magnet.
To remove this old gasket material,
I'm gonna take this razor blade
and very carefully peel it off.
Now I'm gonna take my clean rag
and clean out the inside of the pan,
including that magnet.
So far, this pan is looking great.
Now I'm gonna take this Scotch-Brite pad
and clean off any remaining debris.
The gasket mating surface of this pan
should be clean, bright, shiny metal.
Lastly, I'm gonna spray this thing down
with some brake parts cleaner.
Whoa, guys, look how clean this pan is.
Looks like brand new and the magnet is spotless.
Now I'm gonna test fit my gasket
and it looks like everything is fitting perfectly.
The gasket looks good and all the holes line up exactly.
In order to hold this gasket in place
while I reinstall this pan,
I'm gonna go ahead and slide just a couple bolts in
right through the gasket.
This gasket holds the bolts tight enough
to keep them there,
which in turn holds the gasket in place.
Now that I have four bolts here
holding the gasket in place,
I'm gonna go ahead and reinstall.
Once you carefully fish that pan
back up to the transmission,
trying not to bump anything
so you don't have any debris falling into the pan,
you can start tightening those bolts by hand.
And once those four bolts are hand tight,
we can refer back to our cardboard template.
Again, this ensures that we're putting each bolt
back into its original hole.
Once I've got every bolt finger tight,
I'm gonna take my extension and 13 millimeter socket
and again, go over them by hand.
Next, I'm gonna take my three eighths torque wrench
and begin the process of tightening
in a crisscross pattern.
This is gonna take a couple of passes.
With each pass, tightening a little more.
Make sure you're going in somewhat
of a crisscross pattern.
This ensures that the drain pan is being tightened evenly,
thereby applying even pressure to that gasket.
After a couple of passes on every bolt,
it should be tight enough to start actually reaching torque,
which in my case is 18 foot pounds.
With everything buttoned up underneath
and the truck down off of its jack stands,
we're gonna remove this clear vinyl tubing.
Then we can go ahead and simply reinstall this hard line.
The next step is going to be to refill
this transmission with fluid.
Do not start your car until you refill it with fluid.
In total, we've pumped out roughly 10 to 12 quarts of fluid.
And so we know we're gonna have to replace all that fluid
with roughly the same amount.
I'm gonna start with eight quarts.
I'll start it up, let it idle and get warm
and check the level from there.
With the truck idling and up to operating temperature,
I can now pull the dipstick and check my levels.
And so far, everything is looking good.
All right, guys, here's a little bit of a bonus.
Let's take a look inside our original transmission filter.
I'm just gonna use some tin snips here
to try to cut this thing open.
Gosh, guys, this is actually harder than it seems.
Got it.
So here is the filter media.
It seems to be one piece that's folded over on itself.
Let's go ahead and pull it out and look inside.
Oh my gosh, guys.
Look at all this metal.
These are all metal shavings,
which most likely came from this tranny
during its break-in period.
This is precisely why I wanted to get this filter
and fluid changed immediately.
Man, there really is a lot of metal in this filter.
All right, let's take a look at the fluid
that now resides inside of our 4L60E.
Look at this stuff.
Nice, bright red, brand spanking new,
fully synthetic transmission fluid.
And now let's take a look at the stuff
that was in there for the last 24 years.
Here's the new stuff and here's the old stuff.
And here they are side by side.
Would you have done what I did?
Comment below and let me know.
Make no mistake about it, this is no easy task.
First of all, you're dealing with transmission fluid
and who wants that all over their hands and face?
Second, that tranny pan has 16 bolts in it
and is still full of fluid, even after flushing it all out.
So when you drop that pan,
it's highly likely that you learn right then and there
that that beautiful cherry red transmission fluid
does not taste beautiful or like cherries.
Wow, I am stoked though.
I finally did it.
I conquered that mountain that is a transmission
fluid flush and filter change.
The last step is to drive the truck
and to see if that tranny is gonna blow up.
Because we all know the school of thought that says,
hey, never ever flush your old transmission fluid.
It can cause slipping, it can cause your transmission
to completely blow up, I mean, the list goes on.
In my case, I just chose to change it.
I love this truck and I wanna keep up with the maintenance.
I can't stand to know that there is 24 year old
transmission fluid floating around in there.
So I guess time will tell.
Hey, if it blows up, at least I'll have another video
where I put in a brand new transmission.
Hopefully this video was entertaining for you.
If it was, please hit that thumbs up
and also if you're not a subscriber,
what are you waiting for?
Subscribe.
I'm Jimmy and this is One Road.
