โโโโ ๐๐๐๐๐๐ ๐๐๐๐๐๐ ๐๐๐๐ ๐๐๐ (๐๐๐๐๐ ๐๐๐๐๐๐๐๐๐๐๐)! ๐๐๐ ๐๐๐ ๐๐๐! โโโโ

Charleyโs Garage
78 followers
A quick explanation on what valve overlap is, how it can help with a tune up, what a diesel tune up is and why they are important.
#Diesel #dieseltechnician #tuneup #valveoverlap #enginepower #HEUI #cummins #cat #caterpillar #valves
Hello everyone. I just wanted to welcome everybody back to Charlie's Garage and I wanted to do a
quick video on what is valve overlap and how it pertains to diesel engine tune-ups.
So if you look around me right here, we see a whole bunch of small mid-range diesel engines
and they have a couple of things in common. Despite the fact that some of these are internationals
like this one and some are Cummins like those over there, all these mid-ranges share one common
thing and that is that the tune-up procedure on them is relatively the same. So every inline
six-cylinder diesel engine has a firing order of 1-5-3-6-2-4. So they also have companion cylinders
and a companion cylinder is a cylinder that travels up and down at the same time. So for example,
the companion cylinders on this one, cylinder number one and cylinder number six are travel
companions, but just because they're both traveling up at the same time does not mean
they're on the same stroke. They're actually on opposite upward strokes. So if cylinder number
one is coming up on the compression stroke, it means cylinder number six is coming up on the
exhaust stroke. Now why this is important is that it can help you identify engine position. So
if we think about the compression and power strokes, our valves are closed during those
entire strokes, which means that the rocker arms during those strokes are going to be loose like
this one, right? So if we look along this engine, here we have a rocker arm that's really tight.
That means the valve is open. The only time on an engine like this that both valves are open at the
same time is top dead center of the exhaust stroke. So that's what we mean by valve overlap and it
only occurs at top dead center of the exhaust stroke. So that means if I can identify that
cylinder number six is in valve overlap, that means that it's at the top of its exhaust stroke,
which means its travel companion cylinder number one is at top dead center of the compression
stroke. Now why is that important? Because anytime you're doing a tune-up on one of these engines,
it's going to have you look for overlap, usually on cylinder number six. When cylinder number six
is in overlap and one is on compression, then you'll usually see a typical tune-up chart that
tells you you can adjust both of these valve lashes and then it's intake, exhaust, intake,
exhaust, and neither, right? And then you rotate the engine 360 degrees. When you rotate the engine
one full rotation, what it does is it takes this one from top dead center exhaust and puts it into
top dead center compression and now number one will be in overlap. Now you can adjust all the
ones that you didn't adjust before. So it's exhaust intake, exhaust intake, and both.
That's fairly simple. So the process with this, the reason why we have to adjust these on a diesel
and the reason why we call this an overhead set or a diesel engine tune-up is because as components
wear in the valve train, especially the valve seat and the valve face, it changes the clearance
between this valve bridge and this elephant's foot on the rocker arm. And what happens is you
start to lose the distance between the two that allows room for heat expansion. That could cause
a valve to hang open when it's not supposed to or it can cause it to delay the opening of the valve
or affect the valve duration. So by doing a tune-up and readjusting the valve lash or the clearance
between these two items right here, what we're doing is putting it back into this factory spec
for allowing room for that heat expansion. Some vehicles will ask you to do the exhaust at say 25,
26 thousandths and an intake at 20 thousandths or 10 thousandths. But some engines like this
international, they want the intake and exhaust and everything adjusted to the same. On this engine
it's 19 thousandths. So how do you do the adjustment? It's pretty simple. Put a feeler gauge right in
here between this rocker arm elephant's foot and this bridge right here. And then you're going to
feel for drag in between the two with the feeler gauge. This here is the lock nut that locks the
adjustment in place. You would need to loosen this, back off the adjusting screw, put your feeler gauge
in, and then adjust the adjusting screw while you feel for that drag. Once you have the proper amount
of drag, then you tighten the lock nut. Always double check after you've tightened the lock nut,
recheck your lash because sometimes you'll end up turning this adjusting screw when you tighten this
nut. So what I usually like to do is I'll adjust this until I get just the right amount of drag
and then I'll back the adjusting screw off just a little bit and then I'll tighten up the lug nut
and that usually brings me right back to that perfect spot. But always recheck. The other thing
you always want to recheck is before you put the valve cover back on one of these, check in the head
area and make sure that you have gotten all the tools and parts and everything out of it. Just
think about what one little ratchet or something could do inside here if you left it in. It could
cause some major damage. So always double check for tools and parts before you finish up. And then
also double check to make sure you did the adjustment right. One of the things you should see
is if you think about it, we're only compensating for a few thousandths of an inch of wear here and
there. So when you look at the adjusting screw and the lock nuts, if you see a huge difference
in the amount of thread showing from one adjusting screw to the next, that's an indicator that
something's wrong and that could be anything from you adjusted it improperly or maybe it has a bent
push rod. So never just assume that you did it right. If you see something like that, always go
back and try to re-perform that adjustment. And if it won't adjust correctly, then start
investigating. So whether you're working on an international like this one or a Cummins like
this one, that procedure is still the same. You adjust half the valves with number one at top dead
center compression and the other half of the valves with number six at top dead center compression.
This is a critical thing and what's nice about this is if you remember the tune-up procedure,
right, if you remember which valves to adjust with one at TDC compression and which valves to adjust
with number six at TDC compression, really the only piece of information you're missing is what
size fueler gauge that you need for each one. And luckily for us on most diesel engines that can be
found on the engine's data plate. Valve lash adjustment is often a common thing they put on
there. So if you're working on a friend's diesel and he has a small medium duty truck and you've
got a diesel in it needs a tune-up, just follow this simple procedure and you'll be set. If you
have any questions, please put them in the comments. Please like and subscribe. And to
subscribe quickly, just push the little Mustang down in the lower left hand, right hand corner.
Thank you so much. See you later.
