โโโโ ๐๐๐๐ ๐๐๐ฅ๐ข๐๐ฎ ๐๐๐ซ๐ ๐๐ญ๐๐ซ๐ญ, ๐๐๐ซ๐ ๐๐๐๐ฎ๐ข๐ฅ๐. ๐๐๐ซ๐ญ ๐! โโโโ

Charleyโs Garage
78 followers
1 Video ViewยทJun 5, 2026
Freshening up a carb on a 1971 Chevy Malibu. Rebuild kt, float, choke pull off and choke thermostat will be replaced.
AI GeneratedยทMay contain errors
Alright, so we're getting ready to head over to a guy's house who hit me up on Facebook. He has a
71 Malibu that he says cold start issues. It starts up fine and stuff when it's warm but
has issues getting it to start when it's cold. So of course we're going to go and
check the obvious things out and kind of give him an idea of what it's going to take to fix it.
Hopefully it's something simple like a choke adjustment
or maybe it just does a bad check valve in the fuel pump or leaking carb jets or something like
that. But we'll take a look at it for him see what's going on and then he also has an oil pressure
gauge that he says he wants installed. So I want to kind of check that out find out what kind of
gauge it is. Find out if he has the right sending unit for it or if it's a fluid gauge or and I
haven't seen any of this stuff yet. I haven't even seen the car. So when we get there I'll show you
the car and we will go from there. 71? Yes. 71 Malibu? Yes. Pretty nice. So we checked out the
choke and it was good. Fuel pump's pumping out fuel. Pulled the carb off. Gonna find some place
that knows what they're doing to rebuild it because like I told him I'm not very good at
these older ones. Especially the small ones like this one. So next step is to rebuild the
car bring it back in put it on and test it. All right so we are going to rebuild this carb. So
I went to a website called Carbs Unlimited where you can find really cheap carb parts. Good quality
ones too. So we ordered a carb rebuild kit, new filter, new check valve and the new thermostat
and pull off for the choke and a new float. So we're going to basically rebuild the carburetor
for this guy and you can see that all the parts to rebuild the carburetor come out to about 112
bucks. Looking online this car buying a new one to replace it would cost about five to six hundred
bucks. So if I charge him a hundred and then a hundred for parts he's still saving three to four
hundred dollars on this guy. So now we're just waiting on parts. Okay so we got our carburetor
off. We got it on the bench here and you can see it's a Rochester two barrel. All right got a nice
clean surface laid out for us. So the parts kit that we ordered this is the rebuild kit right here.
You see it comes with gaskets, a base plate gasket, all the odds and ends after you clean it up to
rebuild it. But the place I ordered all this stuff from was called Carbs Unlimited. What the carb
rebuild kit did not come with was it did not come up with the choke pull off, a new float, a new
filter and a check valve and I also got the part that mounts to the intake manifold. This is the
coil that controls the choke. So I got all that new stuff. So the other thing that I bought off
of Amazon is about 34 bucks is a can of chem dip. Chem dip is what we use to clean these carburetor
parts and to get it really clean what you want to do is soak it. So since it's a Friday I'm going to
tear this thing down a little bit not all the way but enough to put it in the cleaner and let it soak
over the weekend. So what I'm going to do is I'm going to separate the base plate. I'm going to
separate it right here by taking these screws up here on the top off and then I'm also going to
remove this piece because we have a new one sitting over there waiting to go on it. And then what we're
going to do after we separate these pieces is we're going to soak them in that chem dip and
when I come back, excuse me, on Monday we'll hopefully have some clean components. So what I'm
going to do is basically I'm going to take this apart kind of show you what it looks like while it's
apart and then I'll make this part one of the video and then part two will be the rebuild and
reassembly of the carburetor. Okay so you can see we've got it taken apart now you got the upper
part with the bowl, you got the bottom part with the throttle plate, and then you got the very
bottom of the well this is actually the throttle plate. You can see this part's pretty nasty.
Inside of this looks pretty good. It's not the worst carburetor I've ever seen in a long time
and this is the filter that came out of it and this is the new one so you can see even the filter
is not that bad. The float looks okay so I get a feeling that I'm probably not the first guy that's
ever been in this carburetor but it was definitely time. Some of the stuff looked pretty worn out
so we've got the small parts the nuts the bolts and stuff like that we'll put in the basket put
it in the chem dip and then we're going to take the smaller component or the bigger components
and put them in there as well first so part two we'll start reassembling this guy.
