Everything You Need to Know About Cummins HPI-TP Fuel Systems

Charley’s Garage
78 followers
A short introduction and explanation of the Cummins HPI-TP fuel system where we introduce the Integrated Fuel System Modules (IFSM) and the components that make it up. Please like and subscribe and share this video with aspiring diesel techs.
#diesel #cummins #fuelsystem #training # hpitp
Become a member of our channel toaday, get great perks and access for help! Also check out the great merch in the garage
https://charleysgarage.myshopify.com/products/darkside-diesel-charleys-garage-original-backpack
#dieselpower #diesel #cummins #CM870 #CM871 #HPI-TP #OLDSCHOOLCUMMINS #training #mechanic #dpf #dieselengines #diy #repair #
AI Generated·May contain errors
Hey, I wanted to take a minute and talk about some of the old school Cummins. So if you young guys,
you know, might be used to your ISX-15s and so forth, but if you see one of the older Cummins
come in the door, you still need to know how to work on them and don't want to be surprised by
how different they are or what some of the terminology is. So over here we have the ISX HP
ITP engines, the CM870 or I think it's 871, not sure which, but it's over here. And then if we
look at our cabinet that we got here, this is called the IFSM or integrated fuel system module.
I got it locked up in a cabinet because I don't want people stealing it.
But if you look at the IFSM, you got your fuel filter right here. And then up here at the top
is where the electronic controls for that fuel system happen. So you look at this whole thing,
you got four of these things that look really similar. And then you got the guy in the middle,
this guy in the middle is the fuel shutoff solenoid. The fuel shutoff solenoid is what
allows fuel flow to go through this module and eventually to the injectors when it's energized
and open with key on, right? These two, the outside one is the metering actuator that determines how
much fuel the injector puts in the cylinder. This one is the timing actuator that determines how
much fuel gets placed between the upper plunger and the timing plunger. And basically since you
can't compress a fluid, the amount of fuel you put between the two changes the timing
on the injector. So you have metering, timing. Come over here to this side, you have metering,
timing. So what's happening is that this one is controlling the metering and timing for cylinders
one, two, and three. These two are controlling metering and timing for cylinders four, five,
and six. And what's really unique or cool when you're troubleshooting this that I really like,
what I found out back in the day, is let's say that one of these metering actuators fails.
When ours failed, the symptom was a whole garage full of black smoke because it was really over
fueling. So the code that it threw though, when we hit the troubleshooting chart for it to see
what it recommended that we do, the first part of the troubleshooting code said to take this metering
actuator and swap it with this metering actuator. And I guess the whole concept behind this is that
this has a different fault code if it fails than this one does because the wiring harness, right?
So if you change these two and the fault code changes, the problem is in the wiring. If you
change these two and the fault code does change, then it followed the metering actuator. I'm not
even sure I said that right the first time. If you swap the two and the fault code doesn't change,
the problem was in the wiring harness. If you swap them and the fault code follows it,
becomes a new fault code, then you just took the bad one, put it in a different circuit. So
it's the solenoid or the metering actuator itself that's bad. And I think you could
probably do the same thing with the timing actuators. But this is a pretty unique fuel
system. It's also a mechanical fuel system, whereas as far as actuation goes, so unlike
high-pressure common oil where there is no actuation except the pressure, and a Huey engine
where you use oil for actuation, this one is similar to our EUI engines like in the Detroit's
where you have a rocker arm pushing the injector plunger down. And the only difference between this
and the EUI injectors is that the electronic controls aren't at the injectors, they're on
this module. So I hope this might have made this fuel system a little easier to understand. So now
when an older Cummins comes in the shop, you've got an idea that this is an integrated fuel system
module that consists of the filter, the shutoff solenoid, and the metering and timing actuators.
And then up here at the top is the gear driven off of the camshaft fuel pump. So I hope this
helped. I hope you liked it. If you did, please subscribe and please share this video with other
people that might find it
