Antique Seth Thomas Overhaul - Part 3 - Removal From Case & Spring Letdown

Chrono Chronicles
8 followers
4 Video Views·May 27, 2026
This is part of a complete clock overhaul video, describing in detail the typical steps taken and tools needed to complete a project such as this. This is part of a long series of videos mainly for educational purposes.
AI Generated·May contain errors
Video Summary
AI GeneratedThis video demonstrates the initial stages of disassembling an antique clock, focusing on the safe removal of the movement from its case and the critical process of letting down the mainsprings to prevent injury or mechanical failure.
okay so the first thing we're going to have to do is we're going to have to take the movement
out of the case so what i'm going to do is very carefully because remember this is old
as if you didn't already know that um we're just going to lay this down on its back like that
it's probably not a good idea to let the weight of the door rest like so so what i do is i just
find something that will prop it open so i'm just going to use that oil that oil sprayer for right
now okay now with the clock on its back and my hat brim and glasses getting in the way hello
we're going to start by inspecting what needs to come out if anything prior to taking the movement
out the last thing we want to do is have a problem where something gets hung up and then
we potentially break something uh what i'm going to do to start off here i'm going to take the um
the alarm dial off so what we're going to do here is we got to take this wire off and this whole
matter of fact oh that's encouraging oh that's nice it's a wood screw hooray for whoever did
that okay well that actually simplifies the taking apart of the movement so anyway this
was part of the alarm setup that it rested on a cam on the back side of the uh on the back side
of the dial but i do believe that's everything so now we're going to get our slotted screwdriver
and i'm actually going to start at the top because it's the hardest to for me to see i
always like to start with the hardest part but anyway so we're just going to loosen the movement
screws and they're easy to see they're easy to tell what you know their purpose is um there's
another one let me stand up here and try not to block the camera there's usually four
and depending on the maker of the clock and the time period that the clock was made they may not
have these holding feet like this like this one does some of them are held in by blocks of wood
yeah crazy right two on the bottom there's no way i'm doing this one now i gotta be really
careful on the bottom because the paper uh the paperback with the name on it i really want to
try to not mess up and here's another handy dandy tool that i forgot to mention it's got little
grippies you push up on the bottom it's hard to see the camera's not focusing on it but
they have these little push-up feet or these little feet on there and uh it's wonderful
for grabbing screws that are in hard to reach places you can even kind of undo screws a little
bit with them there we go okay so now i do believe we are ready to lift this out of here
just a visual inspection here to make sure nothing's hitting anything
pay attention to the hammer and not get it caught on something
all right and what i'm going to do is i'm going to grab it by the plates
at the top and the bottom and then i'm just going to very carefully lift it out like so
always keep it supported okay and that's the only thing i'm going to take out of here so i'm just
to go ahead and close the door and the clock is now without a heart this is going to be our main
focus right here we are ready to start doing stuff we're going to take this off this thing
that i'm wiggling here it goes right here this is the suspension spring and rod or pendulum leader
or whatever you want to call it um all you got to do is just kind of move the the end back and
forth here here you know what i'll make it easier for you to see what i'm doing here but you just
kind of it fits into a little slot here and you just very slowly run it back and forth lift it
out you can kind of let it fall there sometimes you can get them to fit through the bottom
this one does oh my goodness okay that's rare um what i'm going to do is i'm going to remove
this little doodad right here what this is for is adjusting um what the hour striking
point is so what i'm going to do here is i'm just going to open up this little
bent over eye hook here in fact i have to open it up quite open maybe i can get
straighten that out and we'll just lift that out it's through another eye right here
which i do believe is original and we're just going to move that over to the out of the way
pile now what we're going to do is we're going to let down these springs that's where this comes
now i'm not exactly sure what size these winding arbors are so we're just going to do a little
trial and error this one's a six hook i do believe how about a five nope it's a six
okay which is a fairly common size for these older clocks honestly i was just guessing i got very
lucky so anyway what this is for is i mean yeah you can wind it like this and you can see how the
little winding thing works on the bottom but anyway um what i need to do is stop that from
happening so i need to let down the spring but before i can do that i actually need to
wind it up a little bit here
and get it almost completely wound which is pretty close to where that is there now we're
going to take this off lift the movement up and i need to work this around the back
and around that way like that okay i'm going to do this one at a time we have to do this side too
but i'm starting with the time side because quite honestly the ticking is bugging the crap out of
so what we're going to do here is i had somewhere a little doodad you know what i'll just use this
this file right here but what i like to do is try to hold the movement down as much as i can
so i have this system that i devised where i drilled a little hole
table and then i stick a little something through there and then that way it kind of
holds it at one point so that way i can go ahead and turn this now what i'm doing
i know this is going to be impossible for you to see from this angle but there's a click
in here where it falls on a on a sprocket of some sort it's like a cam
and what i'm doing is moving that out of the way i might be able to show this actually let
me go ahead and bring this in while these clocks are going off we're going to loosen it up we're
going to tighten the grip here and we're going to lift this up past the point and then we're
just going to let this unwind okay all right so now that you see what i'm doing there i'm going
to zoom it out so you can see what my hands are doing pushing that up opening that up and then
we're just very slowly letting the spring down okay stopping every so often to check where the
the clamp is okay we're still pretty loose so you can even kind of do this but just do it very
slowly just take your time you don't want to snap it because if you snap it um like if you
let it snap you know like unwind real fast sometimes um you can actually break the spring
that way but always you always want to take your time when doing this and what i like to do is i
like to get the clamp centered in the center of the spring sorry i didn't mean to bump you there
holding thing here yeah see it's not centered and it's tightening up in there so that's good
this side i just like to make sure it's as centered as possible and plug in get back to this
okay and now we can let it down all the way which with this system that they have on here i actually
need to take something else off of here can you believe it this here is
it's a way that you honestly don't even need this but what it is is it's it was something that
somebody came up with years ago when they first made these because people they always said oh
don't overwind your clock you'll break the spring well that's not you know strictly true
um a lot of people and you will find these movements where they've been taken off and
they're just gone so just warning you ahead of time on that and then this lifts right off
presumably okay so now that shouldn't be a problem get my light back in here where i can
see something let down tool back on and i'll finish this out we are now completely let down
on that clamp i'm going to do the same to this side but i'm going to avoid having to stop in
the middle and just take this off now i'm actually going to keep these separate from each other so
i know which side they came from it really doesn't matter but i care so you know now this
one i might be able to show a little bit better i don't know but since i basically explained it
already over there okay yeah that is a much better vantage point i do believe a lot easier to see
just put my arm out of the way okay provided i can see what i'm doing so i'll just look at the
camera and wind a little bit here i'll zoom it out a little bit now that you see what's going on
there and again sometimes it'll want to jump on you but try not to let it do that there's my spring
clamp in the center okay it is now this is pretty much all the way okay there we go
okay and that as they say is that so now we're gonna zoom out
and now the next portion of this is actually just taking it apart
so now we're gonna go ahead and work on that let me get you a different view though
