How to Properly Cut Lathe Soft Jaws — Part 1: Fundamentals and OD Gripping
7 Video Views·May 19, 2026
In the first of a two-part installment, a Haas certified machinist explores our recommended lathe soft jaw cutting/boring techniques and the proper way to cut OD gripping jaws.
Watch Part 2 — ID Gripping, Re-cutting, and Adding a Taper — here: • How to Properly Cut Lathe Soft Jaws — Part...
Don’t miss any Haas videos. Click here: http://ow.ly/s28l30mTiUo
AI Generated·May contain errors
Video Summary
AI GeneratedThis video guide from Haas Automation explains the fundamentals and proper techniques for cutting and using outside diameter (OD) gripping soft jaws. It covers material selection, mounting procedures, the use of boring rings and plugs for stability, and the importance of clamping pressure and lubrication to ensure part concentricity and machine longevity.
Welcome to the Lathe Soft Jaw video series brought to you by Haas Automation.
Soft jaws offer several benefits not provided by hard jaws. They align the workpiece exactly
to the spindle center every time and locate the back face precisely. They are required when
holding difficult shapes and any part that must be made accurately. Today we are joined by Andrew,
one of our Haas certified technicians. In this video, we will demonstrate the proper way to
cut OD gripping soft jaws and cover soft jaw fundamentals. The first side of this bearing
housing has been completed. We will show you our recommended soft jaw cutting methods as we make
the jaws to hold the finished first side of this part. Soft jaws will allow us to maintain the best
concentricity to the accurate surfaces we've already machined. Before we start cutting,
let's go over some soft jaw fundamentals. First, we need to choose whether we'll use aluminum or
steel jaws. Aluminum jaws are typically used to grip lightweight or hollow parts where clamp
force is low. Steel jaws will be used where clamping forces are higher and jaw longevity
is important. Second, it's important to choose the right size jaw. Soft jaws are available in a few
different sizes. When choosing a jaw, it is recommended that you hold at least one-third
of the workpiece length. For a tall part, we can hold the recommended one-third length with a
taller jaw. And for a smaller part, we can still hold one-third of the part with a small jaw.
As the jaw height increases and the part moves away from the chuck face,
the clamping force on the part naturally decreases. If the clamping pressure is set too high in an
attempt to increase the clamping force, the soft jaws will be distorted, actually decreasing grip
force, and the additional leverage from the longer jaws can overload and damage the chuck.
Instead, refer to your chuck documentation to find a balance between grip center height
and clamping force. Before we mount the jaws, it's a good idea to clean the serrated faces
of the soft jaws and master jaws and the T-slots as well. While we are working at the chuck face,
it is worth noting that you should never operate the chuck with the cover plate removed in an
attempt to gain additional part clearance. This cover protects the internal moving parts from
contamination. If contamination occurs, chuck life can be significantly reduced. You can mount your
jaws in a variety of positions, but we chose this position in order to conserve our jaw thickness
since we plan to reuse these in the future. Never position the jaw T-nuts outside of the edge of the
chuck body. When first mounting the jaws, it's a good idea to set them out as far as possible,
just as a starting point. Andrew positions the jaws outwards until the T-nuts are near the edge
of the chuck body. When attaching the uncut jaws to the chuck, always torque the jaws in place
and refer to the chuck documentation for the correct torque value.
In our case, Andrew will torque the M12 bolts holding these steel jaws to 80 foot-pounds.
Use a smaller torque value for aluminum jaws to avoid distorting the screw seats.
It is also extremely important to lubricate the chuck once a day using two or three pumps of
grease per jaw. Use Chucky's grease or an equivalent boundary lubricant with a high
percentage of molybdenum disulfide. If you aren't lubricating the chuck every day using
this specific type of grease, clamping force can diminish by 50% or more. When machining soft jaws,
they must be clamped tightly against some type of object. One of the best ways to keep soft jaws
in position for cutting is to use an adjustable boring ring. The boring ring has three adjustable
dowels that are meant to be inserted into the jaw screw holes. These slide along the slotted ring
body during adjustment and lock in place against the ring when the jaws are clamped. This design
allows for slight changes in clamping position to be made easily. When the soft jaws are held
tight for cutting, the master jaws should be at the middle of their travel. The chuck clamps most
efficiently at this middle travel position. This also allows for adequate clearance when loading
parts and for variations in workpiece size when the jaws are used later in production.
On Andrew's initial ring placement, we see that he is clamped at the very top of travel.
Machining the jaws at this high stroke position would make part loading very difficult,
since the jaws would only open a fraction larger than the part size. Conversely, if Andrew were to
machine the jaws at a low stroke position, the result would be jaws that have very little travel
remaining to grip the part past the nominal diameter. In order to clamp in the desired center
of stroke, Andrew unclamps the jaws and rotates the boring ring body slightly counterclockwise
to bring the adjustable dowels inward slightly. The boring ring is now clamped at the center of
the stroke. As you look at your setup, visualize the direction you will be clamping in. Always be
sure to clamp with the jaws against the boring ring in the same direction that you will hold the
workpiece. Also visualize the amount of force you will be clamping with. During jaw cutting, clamp
the jaws with a force as close as possible to your planned part gripping force. As a basic rule,
adjustable boring rings can be used up to 100 psi maximum pressure and 900 rpm maximum speed,
but don't exceed the manufacturer's specifications. In our case, we will be clamping the part at 130
psi and the jaws at 100 psi. The difference of 30 psi between these two pressures is not enough
to cause problems on this particular part. Keep in mind that there are many situations where you
will need to clamp your workpiece at a pressure much higher than your boring ring will allow.
We will address that scenario in another video in this series. When you are setting the part
gripping pressure, remember there should be a balance between holding force and deformation.
High jaw force deforms both the jaws and the workpiece. Low jaw force may allow the workpiece
to spin inside the jaws during machining. It's a good idea to reference the chart posted on the
side of your machine. Remember, spindle speed also affects outside diameter holding force.
Centrifugal force pulls the jaws away from the workpiece and reduces gripping force as spindle
speeds increase. Set your chuck pressure based on the highest rpm in your program.
To demonstrate the loss of gripping force, we will use this electronic gauge,
which displays how much force each jaw is exerting against the workpiece. With our chuck pressure set
at 250 psi and the chuck stationary, each jaw is pushing with 19.6 kilonewtons of force or 13,000
pounds of total force. With the chuck spinning at 3,000 rpm, you can see that the clamping force
is reduced by more than half. Now that our preparations are complete, we can use the
Haas intuitive programming system to set up our jaw boring operation. We start at the ID turn tab.
We'll be using tool 1 and work offset 54. We leave Z starting point set to 0, so our boring cycle
will start at the face of the jaws where we set our G54 offset. We set inside diameter to 2.2 inches,
just clear of where the insert will start cutting. Our part's nominal outside diameter is 3.950,
so we set diameter to cut to 3.95 inches. Cutting our bore to one inch deep will give us more than
one-third part length grip. We set the remaining values conservatively based on the insert we're
using to cut these steel jaws. When boring, OD gripping soft jaws cut the inside diameter of
the jaws to the nominal workpiece diameter. In our case, the blueprint shows a diameter of 3.950,
and so we will bore to the size of 3.950 inches. This graphic illustrates what would happen if you
did not cut the nominal part diameter. Undersized jaws will grip along six edges, whereas oversized
jaws will grip only along the center of each jaw. Our program is set to cut at the nominal part
diameter. The soft jaws are clamping inwards on the boring ring at 100 psi, which matches the
direction and pressure we'll use when cutting the parts. The master jaws are at the center
of their stroke. Now we're ready to cut these jaws. Once the jaws have been cut, make a shallow
groove at the bottom of the jaws. Any workpiece with sharp edges will now locate correctly against
the jaws back face. Without this groove cut, a sharp edged part will not locate correctly on the
back face. You will likely need to deburr the jaws when the machining is complete. Now that
they have been bored, grooved, and deburred, these jaws are ready for use. In some cases, you won't
be able to use the adjustable boring ring because the part diameter is so large that the ring itself
will block your cutting path. That's exactly the case with this part here. In this case, since we
can't use a boring ring, consider using a plug of material to hold the jaws in position. Before
profiling the jaws, we will take a small cut on the inside diameter of the jaws equal to the plug
diameter. We will use the adjustable boring ring again to hold the jaws while making this initial
bore. We check the plug diameter and enter it into the IPS diameter to cut field. Boring the
jaws this way will hold the plug in the best possible manner. One of the important benefits
of using the plug is that you can exert full desired clamping force on the jaws. You can
eliminate the need to add a taper to the jaws by matching high jaw cutting pressure to high
workpiece cutting pressure. With the bore for our plug complete, we clamp it at the center of the
jaws, leaving adequate clearance for the cutting path. We apply the clamping force to the plug in
the same direction and pressure that will be used on the workpiece, which in this case is 250 psi.
Before cutting these jaws, Andrew notes that unlike our previous part, the finish on this
material is very rough. Despite this variation, in our case we will still cut the pocket to hold
the raw stock at the nominal stock diameter, realizing that in some cases we will be holding
at the six edges of the jaws and other times at the three centers. Now we will be making two-step
jaws for this part, and with our program set to cut both pockets to the nominal size, we are ready
to cut our jaws. Two-step jaws are a good alternative to cutting two different jaw sets.
When part geometry is favorable, the larger pocket holds the uncut raw stock, while the smaller
pocket holds the half-finished part for the second operation. With these two-step jaws cut
and grooved as before, we are ready to start making parts. Thank you for watching. Be sure to check out
our other soft jaw videos, where we cover the essentials of ID gripping and other topics
including adding tapers and re-cutting your jaws.

