Condo/Home Renovation Ideas Made Easy/Part 60

VideoJoeKnows
63 followers
60 Video Views·May 18, 2026
Condo home renovation ideas made easy Part 60 is what this DIY howto video is about. VideoJoe is getting ready to install some doors he just painted on his own. Trust me when I say even YOU should be able to paint your doors & frames like VideoJoe. Why pay someone else when you can do it yourself? Watch & learn as VideoJoeShows you what VideoJoeKnows...condo home renovation ideas made easy Part 60. Nice!
Hmm what or what I'm gonna do today. It looks like work. Yeah, it looks like work. Oh
Look at all these doors no hinges on them. No doorknobs on them. No nothing
Let's see. This is how my doors look after I got them all painted and I brought them up here
I'm getting ready to put them in and it's like which door goes where how on earth do I know which door?
Goes where well, I was smart. I
Made a little list here and I numbered them all here master bath was number one master closet number two master
Bedroom number three guest bath and so forth and so on and so when I go
When I go over here, this is the guest room and I need to put a door on here
And I'm gonna do that one next mommy's been complaining that this room gets kind of cold
She swears that there's no insulation underneath this floor because the garage
Ceiling is underneath here. I'm pretty sure there's insulation in there
And I've also told her there's a heat register right here
and when we turn the heater on the heat comes out of this nice and
toasty and
I told her I says because there's no door on here the heat because the heats down low it comes up and then it's gonna
Travel this way and and and this area here is almost like a suction
Tube and it sucks the hot air right out of that room into this wide open area
Okay, and I told her I told her once we put this door on here
This room is gonna stay warmer that much more and I also told her
Before I don't know if you saw or not. We had just a light up here. We're gonna end up putting a a
Ceiling fan with a light on there. That's gonna be controlled by a light switch over here and it's gonna be the handheld
Remote control and I said in the winter you got your heater on over there
We can turn the ceiling fan the opposite direction
Turn it the opposite direction and it takes your heat as it's coming up
It forces it up and it blows it up on the ceiling and it and then it comes across and it hits this wall
and then it goes back down and then and it's just it just keeps going like that and
I said that will also keep this
Room warm. We've got dual pane windows. We have single pane windows
Single glazed windows. Yes, you could you could change those and put dual dual pane
I mean you could also close the shades when you're not using the shades as much and maybe that'll help
Hold some of that cold air
Out against the window and
So for all of those reasons
Well, I'm gonna do this one
Next and I I know that's the guest room. I look down here
Let's see here
guest bath
Guest number five and so I've numbered them get up here in my
my ladder
And let's see which
which number
See I
Ended up actually putting numbers on both ends because every once in a while you get the numbers they get all messed up and they
get
dirty and sometimes
You can't see them. Let's see. There's number five and
I just happen to write guest bedroom on that one or somebody else did I didn't okay?
So I know it's that one there. Of course. It's the one in the back, right? Of course
It couldn't be just the front one and
We're not using the old hinges we went and bought we went and bought new hinges
I've got all the hinges. I had to buy like 30 some odd hinges and
Their nickel their nickel finish she likes the nickel finish and she also likes the nickel finished handles
Let's see. Here's all that. Here's all the different handles and this time we got well last time
There was paddle handles on here. See this is a bed and bath. So that's not the right one
we need a haul in the closet one and
That's these over here
See here haul in closet because there's no push button on it
These other ones for bathrooms you want the privacy handle with the push button or the little thumb turn
To lock it
So when you're in there
Nobody disturbs you okay, and I even got I haven't got door bumpers. I
Got new door bumpers because the old door bumpers were kind of old and tire
They're 15 years old plus some of them were white. Did you know you can also get these in white?
I made another video once upon a time and
You've got the silver you've got gold like the brass color and you've got anodized bronze
You also have white and you also can get them in different links. See this one here
Look up. Look how much longer that one is see
from that one
Every once in a while you need one
That's longer in case you've got some for some reason the handles hitting in the wall
Or you've got something behind there like like maybe a towel bar and it's hitting the towel bar
And it's barely missing your your don't door bumper. Just get a longer door bumper. That's all you got to do
I think they even make them just a hair longer than this and I like the kind
That are wider at the base. See how that tapers out
See how wide that is and there's a and there's a little base and you just twist this into it
okay, and
for that
I
Ended up you can buy these single you can buy them in a two-pack. This one happened to be a five pack
I've already seen I've already used two and
See value pack you always try to find here five you always try to find things in packs and
in amounts because you know, I bought
You buy these separately. They were like two dollars and fifty cents or
258 or something like that you buy a five pack. They were eight dollars and fifty some odd cents. So
You know, I saved I saved like two bucks buying a
Five-pack basically you buy four and get one free pretty much and and I needed ten
So why not get the pack so I got two free so I saved four bucks on ten
Ten door stops, you know, maybe five dollars maybe five dollars. I saved any case, you know, I'll put those on to you
Okay, so if you want to see me do that, it's not very hard to do this. But if you want to see me do that
Stick around and we'll put well
I'll pull this door out and I'll show you how to put the hinges on I'll show you how to put the hinges on this
door
this door frame and
I'll show you how to pop the door on the hinges. Okay, that's coming up
next
Okay
Now I always like to I always like to lean these doors down against the wall
this
These are hollow core doors. Most interior doors are hollow core
And so I just set it like that
Okay
I've just got it like that. I've got the the hinge cutouts facing out
You see facing out this way facing out facing out lean it up against the wall
Now in new construction, if you don't have the carpet down
I would just take some carpet pad or I take my I take just my little
Knee pad and I would set it down on
One side one end or the other and just let it stick out so I don't
Bugger up or scratch or mark up the face of the door. You know what I mean?
and that's
That's all
I'm gonna do for setting it up
Okay, and and I've got my hinges. I've got my hinges here. I
Always I always pop the hinge pin out
First a little bit now
You can put the you can put the hinges on the door first and then and then poke out this the hinge
okay, so I just
Just get these and and set them down I need them
okay, and
of course, I got to get my
Get my screws
Get my screws ready. I've got my little drill here
Okay, let's see how I'm gonna
I'm gonna set this up so that you can kind of see what I'm doing without me being in the way, right?
You don't have to you don't have to rush see I can pull that out and and of course
I've got the door facing forward. I want to hit so that way I know which side the hinge
Should be facing. I don't want to put them all on there and then pull the hinge pin out and then later think
Oh, okay. I'll just pop it in that way. I like to do it the way that they come
And you can't just set up all your doors. I I would set them all up
You know if I was doing 15 20 doors in a commercial tenant improvement or a house or something
I'd set all these up on up on the wall and I would have a system and you can't just put them all the same direction
Because left hand swing doors maybe are facing this way right hand swing doors. Maybe you're facing the other way
So not you're not always gonna have three knuckles on here. Sometimes you're gonna have only two knuckles on there
right
For for a different handed swing door, okay, so
and I usually like
Like to look at the screw holes
And if I see one like this one here if I were to put that screw in first the hole is is drilled
Too far that direction. So if I put that one in first, it's gonna slide this hinge over
Just to here follow me. So I'm gonna look at this
I'm gonna look at the ones that are centered or off to the right and I see the top one is so I'm gonna do that
one first
The middle one is slightly pushed over that way. This one's even further
but so I'm gonna do the middle one first and
Hopefully that's not going to slide out because I've already got that one tight
Okay, that's nice and snug now and because that one's over as I tighten it up it's just gonna roll over into position
There's no way that one's gonna pull out
I got it nice and smooth if you didn't know that one tip
And you put that one in first and then did these you're gonna have a gap right there
Then when you put this then forever more you're gonna have a gap whenever you open the door
And if that one's at eye level you're gonna see that or somebody else is gonna notice it or your hinge your hinge knuckle your hinge
Pants not gonna go in exactly right because this one's pushed over and the one on the door frame is pushed straight
So, you know different different little
Different little things to be aware of you know
So we'll put this one. We'll put this one in next
I'm just gonna pull
Let's just leave that in. Okay, I
Usually take it out because then it wants to fall off see
So if I'm doing it I
Could set all these up boom boom boom boom boom boom like that set them all up on the door
Now that middle one I'm doing that one first these other two are slid over just ever so slightly
but see now that middle one is gonna hold these other two and
it's almost like that pushed it but
it's
It looks okay because that one's in the middle. These two are off to the side. Both of these should stay in place
I've got that ratcheted type drill
And so that's that's why it's making that I'm not stripping that the screw or anything
Okay, I like the ratcheted
Like the ratcheted drills better than the other the only problem with the ratcheted drill you can't drill
and
Drill bits and stuff because you've got to pull this out
Pop that out and you've got the end
Like that you can get a drill bit with these ends, but still I find that lots of times your drill
Doesn't really want to work before it starts chattering. So I've got a regular drill, too
Okay, I'm gonna do the middle one first
And see because I got it held out
Away from the wall. I don't even have to do anything if you put it too close to the wall
You could have the whole thing slide. You just have to be careful
Okay, that's all I have to do
For that that door is ready to be installed. So now I take the other portion of the of the hinges and
I'm gonna set this up
over here and
I'm gonna put these
hinges on
The simple Simon man, you can do this. Don't you don't pay somebody else to start
Rehanging your doors. This is this is because I I
Didn't install these doors brand-new. Okay, I
Repainted them and if you've been watching all my episodes, you'll see all the different things I had to do
on making these doors
Fit lots of them were sagging beforehand
You don't you don't want to fix a sagging door after you paint think I'll just do it later
No do it first in case something happens. You have to adjust something here. You make any marks on the existing
Door frames the door jam the side of the door jam, whatever. So I've I've I
Had to tweak some of these door frames and all that kind of stuff prior to taking them down
Then I took them down
took all the hinges off took the doorknobs off and then I painted them and I set it up on the out in the garage
and I I show you even how to paint a door and
You know, it's back on one of my other episodes. Okay, look for it on my channel
Okay, so now my second step I got put these hinge the second section of the hinge knuckles on
the door frame now
Because I was paying attention. I know
That on this particular door it gets the
the two knuckles
okay, I
Know that now these these hinges are probably interchangeable
So if they come from the store with with the hinge pin on the top
Lots of times you can put it top or bottom but other times your hinges might have a little
Might have a little thing in the bottom of it
that
No matter what you do. You can't put you can't put it any different direction
Okay without a lot of hassle. I've taken that little thing off before and flipped it around and that kind of stuff but
You shouldn't have to do that if you're paying attention
Okay
These this the hole the pre-drilled hole is in the exact center of every single little hole so
I'm good to go. Don't have to I
Could have put I could have put the top screw in first the bottom screw in first middle one in first
That one didn't really matter
okay, and
You know some sometimes it matters so you just have to kind of
You just have to pay attention. These are all lined up fine, too
Every once in a while you'll find that a screw hole is not
Lined up and then you have to make a decision. Okay, which screw do I put in first?
now see that one is that one is spinning that top screw is spinning and
see there and
If I had to replace that I would have to pre-drill a hole put it in at an angle
Because I couldn't just put a longer screw in there and go straight because the sheetrock
Is a half inch thick that screw is right in line with the sheetrock edge over there
I'd have to put it in an angle, but the other two screws are fitting tight
And if that was the top if that was the top hinge I would be more
Inclined to want to think about putting another
Screw in there sticking it in at an angle and pre-drilling it and getting longer screws and all that kind of stuff
because if a door is ever going to sag which
hinge is
More likely to sag than any of the other ones yes the top one right the top one
this time
I'm gonna. I'm gonna check these with my
Screwdriver
Yeah, see those two are spinning that one's tight those two are slightly spinning
But because it's at the bottom. You know nothing's ever gonna happen to this door. I think it's gonna be fine. I'm leaving it
I'm not gonna. I'm not gonna mess with it now if I wanted to I
could do just the middle screw and then put
Get us get a longer one and drill it a pre-drill it straight into the 2x4 in the back because that
The middle screw is sticking out further than the top two screws. Okay top two screws are lined up with the sheetrock I
Could do it on the middle one if I ever had to do anything to this door
and if something was
Getting funky down at the bottom
I could put a longer screw right there in that middle one
But I'm not going to because like I said the thing is the thing is pretty pretty sturdy anyways and
It's a hollow core door it's only a 6 foot 8 tall doors not an 8 foot tall door and
it's at the bottom and so all the way it's transferred to the center and the bottom one from the from the
From the door you see what I mean and so I don't think this door is ever
Going to sag
Especially down at the bottom if anything if I ever had to adjust it if there was more gap down there at the bottom if I
Had to adjust that and put screws on the back side of that hinge and tweak it out
Then yes, of course, I would have to get other screws
Longer screws to tighten up and not do all that
You know just if you watch if you watch my my videos I got I got a ton of videos
That are not in this
episode series of the condo renovation
If you want to watch those different ones on a different house where I fix all kinds of doors
Sagging doors and all that kind of stuff go to my main channel page
click on playlists and then go down to
doors, you know scroll down the doors any door a
Video that I've ever done on this channel that I posted this channel
I then put on a playlist under those doors if you want to watch those have at it
Okay, so now I'm ready to pop this door into place
See it doesn't it doesn't take very long to do this
You can do this kind of stuff if you're gonna paint
You're gonna paint and you're gonna paint your own doors
And you're gonna change out even if you're not changing to new hinges
You can take the old hinges off. You can replace the the old hinges like for like just like I'm doing
Okay, and and and reinstall your existing hinges. You don't even have to install new ones
We're just installing new ones because she didn't like the brass in here
She liked she likes the nickel finish and and to be honest
Because we changed the paint
This is called double click from Home Depot. It's kind of a gray color
I like it and then I repainted the ceilings white. They weren't white before and
Now
Putting the nickel finished hardware on there. It just it just adds something to to here and
It's a good look. But if you got the brass and if your brass handles are fine and your hinges look pretty good
Hey, put your old ones back on, you know, it's fine
Nobody's gonna know the difference except you if you're trying to save money
That's a great way to save money is to reuse your existing
Hardware your existing door strikes your door stops your door bumpers your hinges your handles your doorknobs
All of that kind of stuff. Okay
All right. Let's get this door popped on the hinges. I've got three hinge pins
Looking for a home
Okay, I could I could leave two hinge pins down here on the ground. I'm gonna do that. These are brand new
There's no grease on them. There's no
Dirtiness on it a greasy marks or anything like that
These are basically dry. I mean I can I can feel just slight
So I leave two of them down there and I leave one in my nail bag
And like I'd leave it in a strategic place in my nail bag. So I know where it's at so I can grab it
Okay, so I'm just gonna leave it down on my nail bag. In fact, if those are greasy, which which
You know some can be honest. I'm gonna just stick them all in my nail bag
Okay
Usually I try to carry it in the same way all the time
But this way I'm doing it different because the hinges are
Facing that way and I don't want to flop the hint the door all around and all that kind of stuff
I just watch what you're doing. Be careful not to
not to
bang anything
Or anything like that. Look at that. I say it I usually carry it. I don't carry it in that way. Generally
I shouldn't have done that because that's the bottom of the door
What the top of the door
Okay
And I got my back support on and my knee brace
And everything and I can just swivel this around just be just be careful and try not to
Try not to whack your doors
Your walls and stuff now all I care about is the top hinge
I don't care if the bottom to line up or anything
All I want to do is get my hinge pin just in the top
The top knuckle and the top knuckle on the door frame. That's it. I don't I don't want to do anything else
Okay, just lining that up
Grab my first hinge pin and
I'm just gonna do that. That's it
If it goes down further fine
But if it's just like right there and if it doesn't go any further don't start taking a hammer
Try to beat it down because you're you're you're your bottom two hinges aren't lined up yet. You could bend the hinge pin
Slightly you could tweak one of your knuckles here. Don't do anything look
This door is not gonna fall down now, but now I'm just gonna
Lift that and work on the second one if the second one goes in fine
If it doesn't then I got to get a hammer and kind of tap on one or the other just a little bit
Okay, that's all the further. I'm gonna go
Okay, because the bottom is not lined up 100% yet
Okay
Until I get that bottom lined up the other hinge
Pins I don't care about I'm not gonna tap those down until I get down here
Line this up pull on the door a little bit line it up push it in that easy. I'm pushing in with my thumb
You know, that's all you got to do and normally I don't push those down and tap them all the way down until I get
The door in until I get it adjusted or or finalized and all that kind of stuff
I'll just tap this down a little bit. I want it
I want to be careful as I do that
So I'm not rubbing the backside of my hammer on the door on the door frame on the door
Casing anything like that. That's it. I don't have to do anything more
I'm not gonna tap those pins down all the way that's how I'm 100%
Happy with this door on
The way it is because if I if I forgot to fix this or for some reason this door shifted
And I got a mess with the door
Maybe I have to tweak one of the the door
Knuckles, but all the knuckles. Well, then I got to take the door back off, right?
So then I don't want to start messing with this
I want this to be nice and easy
So that I can pull these hinge pins back out and all that kind of stuff once I get done with the entire door
That's what I'll tap everything down into place and I'll be real careful when I do that. So I don't mark up the
door
the backside of the door or the door casing
Okay, that's it so far
And you know on this door here. I don't know if they had if they ever put a door bumper on it or not
because
See see where that see where the bottom see where the bottom is it's way out here normally that's where your door bumper is
Could I put a door bumper on here? Yeah, I could I could way over here
until I get until it hits that and
And I might and I might because see what's gonna happen when I put that door handle on it's probably gonna hit that one
see
And I don't know if they if they ever
Drilled and put a door bumper on here from before see there. Look at that. They didn't there's no hole
for the door bumper, so I'm gonna have to make a
strategic
Decision on that and and I'll put I'll put the door bumper on
last
Okay after I put the doorknob on and line it all up and figure out
Exactly where I want to put it or if I want to leave it off or whatever. Okay, you make that decision later
Okay. Well, there you go. That's all that's all I'm gonna do
For right now until I get the door
Handle
Installed I can I can go about my business and I can I can hang other doors if I want
You know, I want to get this door a hundred percent
Today, so once I get the door knob out, I'll put the door strike plate in and then I'll and then I'll
Figure what to do here. And a lot of times I like to this is my pet peeve is where the door latch
Comes out if it's not flush
I need I'd like to line it up perfect because lots of times they just dado this out
With the door machine and usually they're not dadoed out a hundred percent
Perfect seat see this side here where it's really deep this side isn't as deep is it?
And when you if you screw that in tight lots of times the edge of this of the plate of the of the latch
Face isn't gonna be flushed with there
I like them flush now this one here with what's sticking way in too, but after I did my little trick
After I did my little trick look how nice and flush that is. Look at that
See there. That's how I like to see all of them and hopefully you do too
I'll show you that on a different video when I install that
Doorknob, okay
and so
that's
That's it so far and here's here's the other thing too when when
When we installed this carpet, we got a carpet. That's a slight shag
the cut pile is is kind of tall and
initially
The moment was wanting to get a thick
carpet pad a little bit thicker than what was down here and I said no, I don't think you want to do that and
We've got to watch it because the other carpet the
It was cut pile a tight cut pile
And might even even been slightly level loop with cut pile. I can't remember now, but it was tight and
I said we get stuff. That's too thick. We may have to undercut the doors. I really don't want to undercut the doors
I wasn't quite sure how much room was underneath the existing doors
All those types of things you have to consider when you replace your
Carpet and your carpet pad now now see these doors here
It's just barely rubbing on the carpet. That's fine. I'm not gonna mess with that. I'm not gonna
Try to undercut the door by just a hair. I see this one here
Going into a closet. It's just a it's just a little bit and over time the carpet
it's gonna it's gonna lose a little bit of
Puffiness because you're gonna be walking back and forth through here all the time and
Eventually, it's gonna be fine. But right now I don't mind that rubbing the carpet that little bit at all
But if it if it's rubbing kind of hard, oh, yeah now you've got to undercut all your doors
You know, that's not part of what I really wanted to do. I'm calling that good
Okay
