This chair is UN-sittable (technical term, haha). It has loose joinery, breaks and cracks, the wood is incredibly weathered from years of neglect, and is filthy. I don't work on chairs very often, but couldn't resist these. It's not apparent immediately, given the state they are in, but these chairs are made of a lovely and valuable wood.
This is a friendly competition between four channels. Vote by liking your favourite video! The video that gets most likes, wins! The likes will be counted on December 2, 2023.
Today I'm doing something that I very seldom do.
Chairs are just one of those things that are more hassle than they're worth, at least for me.
More about that later.
But check out this pair of Devin Outdoor chairs.
These are rough.
Decades of neglect and we are well past patina territory and headfirst into damage town.
These have been tucked away just waiting for a new life.
So what's so special about today?
Why am I choosing to do this now?
I was actually approached by AT Restoration about joining him and Scott from Fixing Furniture
as well as Trenna from John's Furniture Repair to do a little friendly competition.
And the subject was chairs, or to be more specific, a chair.
Obviously I'm going to do both chairs at some point, but for this video the rules are simple.
Refinish or restore one chair, everybody uploads on the same day,
and whoever has the most likes at the end of the week will win.
This is just a friendly competition, nothing serious, there's no prizes,
but this should be pretty interesting, so stay tuned.
My name is Angie and I refinish furniture.
Sometimes I paint and sometimes I don't,
but I always do what I can to save old pieces from the trash.
Welcome to my workroom.
So a question I get asked fairly often is why I don't do more chairs,
and there's actually a couple reasons for that.
Firstly, that's not what I do in my main business,
so I don't have a lot of the tools required to do super complex repairs on chairs,
specifically like a lathe or something like that.
Also, around here, to find a chair that's in rough shape to work on is almost impossible
unless it's a commissioned piece, and I don't do commissions.
You can't exactly go on Facebook Marketplace and find a broken chair for sale
because people don't sell them, they throw them out.
So unless you're lucky enough to see one sitting on the side of the road,
the ones generally in need of work are either going to
specific restorers as commissioned pieces or they're junked.
Along that same vein, chairs don't really sell that well.
If I was doing a set of like four dining room chairs or something, maybe.
But to sell a single chair or a pair of chairs like this,
you know, these would have come probably in a set of four with a patio table.
That's technically what they're made for.
I only have two chairs here, so the likelihood of selling them as a pair is higher than single,
but still not as good as if it were a full set.
So there's numerous reasons I don't work on chairs that much.
But when this challenge came along, I thought it was a cool idea.
Firstly, because I get to work alongside of other amazing furniture people who do specialize
and do a lot of complex repairs on chairs.
So I thought it would be a good learning experience for me and you.
So I guess what I'm trying to say here is that
even though this is not really my wheelhouse, I still wanted to participate.
And knowing full well that the chairs that these guys are going to be doing
is going to blow these out of the water.
But I wanted to offer kind of an alternative side to it.
All right, so having a look at the first problem here,
you can see there's a big split right where that bolt went in.
And there's a lot of rust bits, so I don't think I'm going to have to replace this board.
I'm pretty sure that I'll be able to glue this up and have it be strong and tight.
But every joint on this chair is loose, so everything is going to have to come apart.
It'll make it easier to sand everything as well,
but the most important thing is getting this structurally sound.
So everything is going to need to be re-glued.
There's another split here on this piece.
This is one of the armrests.
There's no way to get that nail out except to just tap down carefully.
And unfortunately on one side, where the split was on this end was just too vulnerable,
so when I tapped it, it broke.
But I'm pretty sure I can glue this back together as well.
So for this, I'm using Titebond III, which is a waterproof glue.
Now there's no rule that says you have to use these chairs outside,
but it is what they were made for.
For those of you that aren't familiar with Devon Outdoor Chairs,
I want to take a guess at what type of wood this is.
I'll give you a hint.
It's expensive.
It's used a lot outside and on ships.
And it's normally a very different color than what it looks like right now.
Now I wanted to glue these two small pieces in place before I add the rest of it in,
so I'm just using this little wad here to help clamp and put pressure on those.
And then once that's done, I'll glue on the larger piece.
So this is the canvas seat and the back piece.
Original, of course.
They're a bit rough.
The seat is a little bit more faded than the top is, which is pretty typical.
I'm actually going to let these soak in some water with laundry soap for pretty much the entire day.
And I am using warm water.
Sometimes that's an issue with dark colors, but this is outdoor canvas.
It's been in the rain, clearly, for quite some time.
I'm not really worried about it running.
So back to some of the repairs.
This is one of the other more significant splits.
Wherever possible, I like to put the original wood back together.
The only time I'll replace a board is if I can't do that,
or if there's chunks from inside the split missing.
You know what I mean?
Where it won't go flat against each other.
It won't fit tightly.
If they're just small gaps, sometimes I will inject some epoxy in there,
but if they're large gaps, it's better to just replace the board.
But in this case, everything fits back pretty tightly together,
and I should be able to save these.
So the issue of the broken tenon.
I need to drill out what is left of it glued into that hole.
And what I can't get out with the drill press here, I'm going to try to chisel out.
I need to make sure that that mortise is completely clear,
so that when it comes time to manufacture a new tenon to fit inside, it will fit snugly.
I shouldn't even call it a mortise and tenon,
but a tenon is generally attached to a board as in one piece.
These are almost like dominoes or oversized dowels.
So technically this isn't a true mortise and tenon joint,
but the repair is essentially the same.
You'll notice my little vice here hanging on for dear life to that pine table.
It is bolted down, but pine's pretty soft,
so when there's any pressure, it does move a bit.
I am still planning on building another work table
that I can use for things like adding some different vices
and things that will make repairs like this a lot easier.
For now, I'm going to use the wobbly one.
This chair is absolutely filthy,
so I'm giving all the pieces I need to sand a really good scrub down.
Now, you'll notice I'm not scraping or stripping
because there's no finish on this to strip.
I'm literally just going to go in and sand once I have it cleaned.
I ended up sanding every piece on this chair four times,
first with an 80 grit to get through that old weathering,
120 to clean that up, 180 to refine, and 220 to finish.
I had to do something about the rusty hardware,
so once I was done sanding,
I dropped all of the bolts into a bath of Evaporust,
which is a very safe and biodegradable rust remover.
Normally, I let that set up overnight,
but it was actually completely rust free within a few hours.
So I haven't mentioned it yet,
but if you haven't guessed already, these chairs are solid teak.
I do quite a bit of mid-century furniture,
so teak is something I work with all the time.
But for people that don't,
there's a few things about teak you might want to know.
A question I get asked quite often by people working on teak for the first time is,
what are these little white flecks in my teak?
And there's three possible causes.
First is sanding dust from sanding.
Secondly, if it's teak veneer you're working on and it gets quite thin,
sometimes you can see little bits of the substrate underneath.
But if it's neither of those two things,
and you've taken the time to either blow out,
vacuum out,
clean out the pores after sanding,
and you're working on solid teak or veneer that is not too thin,
there's a good chance you're looking at calcium deposits.
And these are literal mineral deposits in the wood
as the tree grows and sucks up the mineral content from the groundwater.
Sometimes you can pick them out with a dental pick.
You'll see me kind of show that a little bit later on,
but it's extremely time consuming,
and unfortunately, it's just part of the wood.
These rubber washers were originally glued to the piece.
I had to remove them obviously to sand,
but now I'm gluing them back on,
and I'm just using some CA glue.
Once the chair is put back together,
these washers are going to be quite compressed,
so this doesn't have to be a necessarily permanent bond.
It just has to stay on long enough for me to get the chair back together.
Super happy with how this hardware turned out.
This Evaporost stuff is amazing.
So now I need to get on to the hardest part of this refinishing job,
and that is replacing this missing dowel,
I guess you could call it, here on this one side.
So at first glance, these might look like mortise and tenon joints,
but they're technically not.
Each section here has a section drilled out,
and then this wood piece inserted,
so one of those pieces at some point cracked,
and I need to replace it.
With the matching side of this,
I was able to put it in the drill press and quickly move it out,
but obviously this piece is too tall to stand upright in the drill press,
so I'm having to do this by hand.
It annoys me that these pieces are rounded.
I wish they were square, and I could cut a square,
but honestly there's not a lot of wood on the end of this,
so I don't want to make that hole any bigger than it has to be.
So I'm just carefully cleaning it out,
taking some measurements to figure out the exact size of the replacement I need to make,
and I'm going to be doing it out of this piece of teak board here.
So I'm just using a marking gauge here to get a really accurate measurement,
keeping in mind that I added about a millimeter,
because I'm going to have to shave this into a certain shape,
so I wanted to give myself a little bit of extra room.
I'm going to be hand cutting this also,
so having the cut lines already sort of indented into the wood will be helpful as well.
And I know that you guys probably can't see these lines,
so I'm just going to use my pen here and just roughly outline the part that I'm cutting out,
and obviously when you see me cut,
I'm not going to be cutting this pen line,
I'm going to be cutting the score line,
but just so you can get a better view of it.
And there we go, this is my block of teak that I'm going to need to round the edges of
and fit into those two holes,
and each of those holes are slightly different sizes,
so this is very much hand tuning.
I'm working it down first to very close to the original width and length of the hole,
and then going back and forth several times to shave just little bits off at a time,
coming back, testing it, rinse, repeat.
Until finally I get to a point where I think it's going to go in,
but before I do that I need to just sort of chamfer the edges a little bit,
it'll help guide it in and give a little bit of space at the bottom for the glue.
I'm just going to tap this in without glue first to make sure it's going to work.
It feels nice and tight, I'm just...
I ended up shaving just the slightest bit off because you don't want it too tight,
there has to be room for the glue.
So overall I'm pretty happy with how this came out,
I have a nice tight fit,
and once I have that first side in, which was the larger side,
I'm going to go and fine-tune this part for the other hole,
which I said was slightly smaller,
and there you have it.
I'm opting to put everything back together before I apply my finish to it.
So these are the two armrests,
and if you remember from the beginning,
they both had pretty significant damage to them.
It was this one that had the big chunk taken off when I tapped a little bit too hard,
trying to get it out,
the nail just hung on and ended up splitting it,
and you can barely see, there's just the faintest line here,
but it's a nice clean finish on the outside,
there's a little chip there, but that's not a big deal.
And on the other armrest was this monster crack here,
and again there's just a little bit of chip out there,
but if you didn't know what you were looking for,
you would never see that repair on these two pieces.
I was super happy with how the glue-up went,
everything held together really, really well,
the chair is sturdy, solid,
I just have a little bit of cleanup of some of the joints from the glue squeeze out,
and then I can go ahead with my final sanding.
Now you'll notice I'm using a half inch foam pad there,
it's super soft,
it's not going to change any of the profiles of the pieces,
it's just smoothing things out for the finish,
and again this is cleaning up those glue joints.
So the pores in Teak, they're quite large and open,
so when I'm getting ready to finish Teak,
I like to, now that I have an air compressor,
blow them out first,
and then I use a tack cloth to try to pick up anything else.
Now when you're using a tack cloth, you don't want to press super hard,
you can actually transfer some of the varnish and oils that are on the cloth onto your wood,
you don't want to do that,
so just very lightly pick up any of that super fine dust that's left over,
and it should come as no surprise that I'm using Odie's oil on this,
I love Odie's on Teak,
but in this situation, because these are exterior chairs,
it's going to be even better.
There are some Odie's products that aren't meant for outside,
such as the dark oils,
this is the original universal oil,
and this is perfect for outside.
There are some that say you don't need to seal Teak,
and that is true, it is quite weather resistant on its own,
but if you want the original color to stay longer,
then you're going to want to seal it with something.
Now going back to those little white flecks I talked about earlier,
these are calcium deposits,
and as soon as you put any clear finish on,
they are going to stick out like a sore thumb.
As far as I know, there's not much you can do for them,
aside from trying to pick them out,
stain over them,
or use touch-up markers to literally paint over them,
and that's actually what I'm going to be doing here.
Thankfully they weren't on every single piece,
but as you can see here, the ones that they are on,
they do stand out quite a bit.
Now like I said, you can try to pick them out,
they're quite powdery and they almost explode
when you're trying to pick them out,
and often you end up just making the holes even larger,
so I try not to pick them out too much
if there are other ways that I can deal with them.
I'm just using some Brasso on this little plate,
which I'm going to replace just to clean it up a bit.
And we are literally in the homestretch now,
so I just want to remind everyone a little bit about
what this video is for
and the little friendly competition we have going.
Basically you're going to vote on these videos with your likes,
so watch all four videos I'm going to link
to the other channels down in the description below.
Everybody's going to put a video out the same day,
watch them all,
and then you vote by clicking like on the one that you like.
You can comment on all of them, that's totally fine.
As always, we're going to want to hear your feedback on our pieces,
but the only metric we're going to be looking at are likes,
and this is just for fun,
and I'm hoping we all learn a little bit from each other.
We each have our own way of doing things,
filming and editing,
and the way we present our videos,
it's all different,
so this is just for fun.
So hopefully you enjoy what we've done here.
I just used some mohawk graining markers to paint,
if you will, over those white flecks.
I have no idea how that's going to hold up outside,
we're going to find out.
And I went to put this plate on,
and if I use the original hole,
it's actually slightly crooked,
which I can't deal with,
so I'm going to make a new hole,
push this up,
and pop that in.
Well, we're pretty much at the end of my very first
specifically chair video,
hopefully you've enjoyed it.
I am going to redo the second chair at some point,
but that will come later.
I'm super happy with how this turned out,
and the reveal is going to be a little bit different.
This is an outdoor chair,
so to me it makes no sense to film it inside.
As always, thank you so much for watching,
enjoy the reveal,
I will see you next time,
and don't forget to like your favorite of these four videos.
See you soon.