The Adirondack chair is a popular piece of outdoor furniture with a rustic, classic look that is both sturdy and comfortable. Follow these step-by-step Adirondack chair plans and get more enjoyment of your outdoor space: https://thd.co/3QvPMFu
What's great is that with a few materials, you can learn how to build a DIY Adirondack chair yourself. You can sit back in its low-slung seat and place a drink or a snack on one of the wide arm rests, making it ideal to take it easy.
0:00 DIY Adirondack Chair 0:20 Step 1: Cut Boards 1:11 Step 2: Cut Stringers 1:42 Step 3: Attach Legs to Arm Support 2:20 Step 4: Attach Stringer Board to Legs 2:56 Step 5: Build Opposite Leg Set 3:06 Step 6: Attach Front Apron 3:34 Step 7: Attach Seat Slats 4:02 Step 8: Build Back of Chair 4:42 Step 9: Build Back Panel 5:54 Step 10: Secure Back of Chair 6:19 Step 11: Secure Arm Rests
About The Home Depot: How doers get more done. We’re helping doers in their home improvement projects. Now you can take on more renovation projects with more know-how. Our step-by-step instructional DIY videos and expert advice will give you the confidence for your next project with hands-on learning. It’s a good time to be a doer.
Today we're building an Adirondack chair. This is a classic outdoor design that's actually pretty
easy to build. I've gathered all my supplies. I'll leave you a full list of tools and materials at
the end of the video. The first step is to cut down the boards. I'm using my trusty miter saw.
From your 2x2s you'll need two arm supports 26 and a half inches long with one 15 degree end
on both boards. From your 2x4s you need two 22 and a half inch pieces for the apron and back support,
one 19 and a half inch back base support, two 20 inch front legs and two 20 and three quarter inch
back legs with parallel 15 degree ends. From your 1x4s you need five 22 and a half inch seat slats,
five 36 inch back slats, one 19 and a half inch back top support and two 27 inch arm rests.
For the stringers that support the seat slats, cut a 35 degree angle on a 31 and 7 eighths inch
2x4. On the other end make a 20 degree cut in the same direction as the 35 degree angle.
Now using your square find the two inch length. Mark the top portion then cut with a jigsaw.
You'll need to repeat this for the other stringer. Now we can begin to assemble the chair. Arrange
the legs on a surface with an arm across the two pieces. Make sure the angled end of the support
is at the rear leg. Apply wood glue then use clamps to keep the top and outside edges flush.
If you pre-drill the holes in this project you can avoid splitting the wood.
Now fasten with deck screws. Next I will flip the assembly over to attach the stringer boards.
Align the bottom corner of the stringer with the back leg. Mark where the front edge falls on the
front of the leg. It should be two inches from the front of the leg. Then glue and screw into place.
Now you'll build a mirror image for the other side. Make sure the arm support is on the outside
and the stringer is on the inside. With both sides built we can join them together by attaching the
apron. Add glue then fasten with a screw through the apron into the end of the stringer board.
Then add two screws through the side of the leg into the apron for additional support.
Clamp the back base support between the stringers to maintain proper spacing until
the back is permanently added. The slats stretch from stringer to stringer.
Begin at the front of the chair and attach the seat slats with wood glue
followed by deck screws. Keep the slat ends flush with the chair. You can use a piece of wood to
maintain the half inch gap between seat slats. Attaching the back support is a little tricky
because it needs to be fastened at an angle. Mark the front edge of the back legs four and a half
inches down from the top. Mark the rear edge of the back legs five inches down from the top.
Now position the back support so that the front bottom edge is at the four and a half inch mark.
Then tilt it down so that the rear top edge is at the five inch mark. Next attach with screws from
the outside of the legs. Put that all aside and let's build the back of the chair. Place the top
and bottom back base support on your work surface with 23 inches of space. Leave a half inch to
three-eighths inch gap between each board and secure it into place. To create that classic
Adirondack look we're going to use a number three wash tub to mark an arc shape into the top.
Then carefully cut with a jigsaw. Next secure the back into the chair assembly with two screws
through each stringer and then with two screws in the back support. It's almost finished. Secure the
armrest to the arm supports and the top of the legs using glue and then screws. Glue in plugs
or use a wood filler to fill screw holes. Then sand off layout lines and soften hard edges.
Paint or stain as desired. This I made with western red cedar so I don't need to stain it
but if you use pressure treated material make sure you let it dry thoroughly before you paint
it or stain it. Now get ready to relax in your outdoor space. Once you're ready to build your
own Adirondack chair here's a full list of what you'll need. Good luck and thanks for shopping at
The Home Depot.