How fast could a Native American really make an arrowhead? In this 10-minute flintknapping challenge, I take a raw spall of Flint River chert and attempt to turn it into a complete arrowhead before the timer runs out.
There’s a common belief that stone points took hours or even days to make, but experienced knappers — both ancient and modern — can work surprisingly fast with the right material and technique. In this video, I push the pace to see what can realistically be done in only 10 minutes using traditional-style flintknapping methods.
From hard hammer percussion to pressure flaking, this challenge shows the entire process from raw stone to finished point in real time. Whether you’re into primitive technology, archaeology, survival skills, or modern flintknapping, this one should be fun to watch.
Have YOU ever tried a timed knapping challenge? And how fast do you think ancient craftsmen could make a hunting point when they needed one quickly? Let me know in the comments.
Is it possible to make an arrowhead in 10 minutes? That's what I want to figure out today. I've got
a piece of caramel flint river chert and I've got a copper bopper and what I want to do is time
myself give myself 10 minutes to try to make a functional arrowhead out of this particular piece.
Length-wise it's only about four inches long and about three and a half inches wide
and once we hit the 30 second mark in three, two, one, here we go. Now there's kind of a
misconception amongst those who are beginning flint knapping or just getting into the hobby
or just learning about it that Native Americans could make an arrowhead in one minute or in 30
seconds or in two seconds as if they were the master crafters and so to speak they were in the
sense that they made arrowheads in order for them to you know do different tasks whether that was
you know to put a little point on the end of a little atlatl dart or shaft or to make a spear
of some kind or to make just a blade surface or a cutting surface or just a little knife,
handheld little knife. Oftentimes they could be used by just smacking you know one piece off
and there you have a sharp edge but in regards to complete you know full form arrowheads
I'm generally thinking of you know the point types that are found in any given region like say for me
I live in the deep south so Florida, Alabama, and Georgia and if you disagree with me on what's in
the deep south you can take that up with me in the comments but for arrowhead purposes we generally
classify those in the deep south as in those particular states and so there are particular
types that if you were to find out in the field that you may find Savannah River, Abagge Branch
Point, you know whatever it may be and they all serve different functions some are small and some
are big but as you can tell it doesn't just take you know one strike and oh there you finished an
arrowhead and of course the natives would have used and utilized things like instead of copper boppers
stone and antler tools to be able to refine their work and get the shape that they're looking for.
Now copper is technically a little bit better and so that kind of amplifies the question
of how quickly are they able to do it but copper is still utilized today
it's just a little bit expensive to buy and of course it's a little bit more prone to
your molding and corroding whether that be because of the weather outside being a little gloomy
or because you know just utilizing it it just weathers far easier than say you know a type of
metal would and so already let's see we're about three minutes in and we've got a nice thin what
I guess you could call a biface it's flaked on both faces of the piece and sometimes you'll
have these breaks and that's pretty common especially when you're working quick like me
for the sake of a video but you can still utilize these particular flakes and you don't have to
start off on a fresh one and from the shape that we have here I'm thinking about going Dalton.
Dalton point was generally made out of raw material and is paleo or close to it
sometimes they're beveled and just the way that this edge is it already kind of has a natural
bevel so I'm in luck now bevels were generally used for sake of re-sharpening a piece
not necessarily for you know looks you wouldn't just go out of your way to make
a beveled point unless you're going for like a drill or something in this case we're just
trying to mimic certain points and you can tell about four and a half minutes in we're already
doing really really well in regards to this Dalton point and so even though we broke it
that doesn't mean that we can't you know have something really nice to to finish with and work
with so we're going to get a slight little flute there nothing too crazy and honestly I have plenty
of time to finish this out however I really see fit so what I'm going to do is I'm going to get
my pressure flaker out actually I may utilize this one first uh-oh where's my pad at I don't know
where my pad's at uh-oh well I guess that happens and I didn't account for finding the little pad
I usually use so this is all we get so this is just a thing of copper I'm just going to press
the edge here and honestly we have time to make this really nice we do so that's what I'm gonna
try to do is make it nice all right so go here try to thin out this back edge a little bit
pretty thick at the moment okay we'll flip it over and this will be the hafting area
down towards the base so as long as we have a nice little semi-thinned out area down here
to after our little little shaft we should be fine now I've done this challenge a number of
ways and with a number of different materials and I've tried different point styles whether that be
Clovis or Savannah River it's the first time I think that I've gone with a Dalton point in
particular just the way that that uh spaw kind of broke it just kind of looked Dalton-y if that
makes sense uh-oh let's get a different bopper don't have much time to lose all right I'm going
to go back on this side actually I think I'm gonna heighten it a little more because this
side is pretty high uh-oh we got a little over two minutes left once it reaches 10 minutes 30
seconds I have to quit this is where I wish I had my other pad but we're able to thin it down okay
now for sake of the edge I don't really have time to do much
pressure work so I'm just going to stick to using a bopper
and because I can I'll get a nice little bevel on there because it looks good
no I'm shaking you all around forgive me now I gotta line everything up a little bit
oh no I dropped it all right I don't yeah I just don't have much time to do anything so
just do a little bit I guess I only have 30 seconds left just kind of shape the base there
of course Daltons are basically ground eight seconds that's probably it and it is
all right well you know what for 10 minutes that's a pretty good beveled Dalton huge bevel on it
it's got some translucence you can see through it and again it's nothing wild or nothing crazy but
it's just a point style that you can find here in the deep south heavily beveled and much smoother
around the base for hafting purposes and you could put a shaft in there and this could be
used as a drill or a knife and if it's not too long as a projectile so pretty cool looks like
we're able to do it and hey I love doing these challenges so if you have more suggestions of
working bigger pieces smaller pieces different time frames whatever it may be just let me know
in the comments and we'll see if we can do it but for today this will be it and we'll see you on
the next video take care