http://www.VideoJoeKnows.com Sanding a drywall skim coat patch is the last important step before priming your patch. If you want your patch nice & smooth & blended in to the existing surrounding areas, you need to sand this skim coat......you'll be sorry if you don't. Make sure the skim coat patch is 100% dry before attempting to sand the drywall area. How much sanding should you do to your skim coat patch?....this may surprise you. Can you sand a skim coat patch area with a sanding pole? I would recommend you use a paddle sander so you can feel the drywall patch area with your hand so you can tell that the skim coat is 100% blended into the existing area. Can you prime the skim coat patch area after that....finally? No. No? No. Make sure to do THIS first, or your primer & paint might not stick properly. "Joe".....you're up....wake up! Let's watch as "joe" shows how easy, sanding a drywall skim coat patch can be. http://www.VideoJoeKnows.com
Now before I sand, I want to make sure this is 100% dry because this tight skim, skimming material
will also shrink as it's drying. That's why I've got to get that that previous coat
nice and full so that when I put this on once it dries it's going to be fine. Okay.
Worst thing you can do is start sanding on this before it's 100% dry because then you're going
to start gouging it. Maybe a certain point part of it is dry and maybe there's some deeper spots
that aren't dry all the way. You can look at those and see those pretty much. If you stand back,
shine a light up here and see this is drying really good. I haven't been off it that long
and it's drying nicely but I'm going to let it dry some more because I don't want to rush it.
Once I put scratches in it from the sanding pad then I've got to put more on there and then it's
going to prolong my project. I want to get this thing smooth and sand it out so I can put the
primer on there today and keep going with my project. Now do you see how much easier it was
to take these light fixtures down? I mean I've been working back and forth through here this
whole time and if these were here and I have to keep moving around and bumping them and sure
anything something would have fallen or I would have backed up into it or lost my balance or
something not got the patch 100% right. It's nice to just get things out of your way especially
with a patch like this. Now I'm just here wondering what to do now. Do I just sit here and wait and
wait until this is drying up to get out there? No. Think about other things you can do.
I'm going to be installing some primer next and the painting after that so I can get all my
paint material set up and make sure I have my extension pole ready and my primer ready and
all the different things I'm going to need for that. So while I'm getting that ready
this will keep drying. Stay busy. I guess it's time to get up here now and sand this again.
Hopefully this will be my last go at this and I'm hoping I don't have to put a tight skim coat on
but we'll see. Now I'm just sanding around the edges again and I can see exactly where I need
to go because of my life. I'm going all the way around the patch. I'm not actually into the patch
just yet. I'm just working my way on the outside of it. Now I can go into the middle and I'm just
going to do a little bit. I'm not going to do much because I don't want to take off very much.
The more I sand the more I'm going to take off and I don't want to do that.
That's looking good especially on the transition from my patch to the existing. I want to feel
that make sure there's no ridges there because I don't want anything to stick out when I get done.
When you're doing this you probably should have a dust mask on. I don't have one on. I'm trying
to stay off to the outside and I don't want my voice to be muffled if I have it on there.
If I have a dust mask on you probably should have a dust mask depending how big your patch is.
Okay now I'm just going right down the middle just a couple times.
It would defeat the purpose if I sand too much. I'm going to get into that bottom layer and get
down to the Kwikset because the Kwikset is not going to take the paint as well.
Plus then I'll have a little gouge in there.
You know when it comes to sanding less is not necessarily the best.
I mean just kind of a happy medium. Actually I want to say more is not
sanding more. You just don't want to do that
on a patch. I've seen some people they don't know what they're doing. They'll put
they'll put on a layer of mud and then they'll sand it and sand it and sand it.
You've taken all the mud off. They just put on. You got to sand that much. That means you still
haven't perfected the technique to put the actual mud on and you need a little bit more practice.
That's all that means. Okay a couple passes down the middle to the end here.
I think I'm good. It's looking good. That's all I'm going to do to this patch.
Get my broom up here. Especially I want to broom it now. I want my prime coat to stick.
You don't do this. You get all done. Your primer and your paint may not stick on the wall properly
because it wasn't dusted down. This is a nice quick easy way to do this. I can see the dust
lying all over the place. I know I'm going to have my hands full. I get ready to clean up
but there's no other alternative here. At least I've got all the windows closed,
fans off, air conditioner off and so everything here that's filtering around in the air right
now is going to come straight down. All right I'm going to let that set for a little bit.
Get the dust kind of settled. Get ready to mix up my paint.