I found the FASTEST way to throw a platter Platter Tutorial.

History culture hero
16 followers
5 Video Views·May 8, 2026
My wife told me I need to make some housewarming gifts for our good friends so of course I said
yes wife you're right wife I'll do it and we're going to go ahead and make two of these platters
they are around nine inches wide by a little under two inches tall with three pounds of clay. I'm
going to show you how to do it in two different ways so if that's something that you want to see
stick around and find out how we do it. So we have the rolling pin that we've used in other
videos to flatten and make discs you can make platters and plates with it we're going to put
that away and we're going to go over the more traditional way on how to make these platters
using three pounds of clay so let's clear this area and let's get started with centering this
guy down. So as always we roll the clay hit it on the board and start pushing down and get it stuck
and you can hear it's like wiggle so I'm going to get a batmaid to get this stuck so it doesn't do
that. So these are called batmaids they're from xeme they're basically just chamois material
and what it does is it helps to stick your board to the wheel or any object to the wheel in general
and that jiggle can make it more difficult for you to center your piece so by putting this material
down I shouldn't get that jiggle and the board should be nice and stuck so this will be posted
in the amazon storefront if you want to pick up your own and you don't have to get the xeme brand
that's the name brand you can get cheaper ones but right there a lot less jiggle. Anyway let's
get this centered and basically we are making a flat disc so the centering process is generally
the same you still cone up you still cone down but this time we're going for a more flatter
wider centerpiece rather than a taller dome but centering still more or less the same cone up
cone down try to get all those wobbles to go up and then down there's still some slight wobble here
so another way that I was showing my students how to get it centered if just the bottom is slightly
off one little tip I have for you folks is when you do the karate chop to cone down you can actually
do this to cone up so with the karate chop instead of just brushing down with my right hand I'm
pushing forward with my left you can see the clay rising up a little bit and then I'm going to push
back down with my right so by doing that I'm pushing the base up and and making it rise and
then my right hand will push it back down if it's still a little off we repeat that so push forward
with my left and then I push back down with my right so you basically are alternating the pressure
forward with the left diagonally down with the right and you keep repeating that until this is
centered so right there a little closer to being centered but I'm just going to cone up and down
one more time just to be safe just really squeeze at the base get those wobbles to rise up and the
way I like coning down I don't actually don't do the karate chop very much anymore I mostly just
push forward with my left hand but this can also be done with your right but I am left-handed and
I'm going to engage at the base here with my sponge hand and my fingers on my left hand to then get it
flattened all right so I have my disc and my goal is to flatten this out to get the width of what I
want my base to be and so this is normally where you get the rolling pin you compress it down and
make it flat but this is another method I call it the hammer push to get this flat and it's very
similar to the rolling pin but you're just using your hands so for the hammer push or hammer
compress basically you just make a fist with one of your hands either or left or right doesn't matter
and you're going to brace up against the clay with one hand and then the fist hand is going to be
pushing down in the center and you're slowly bringing it towards your body and then my
hand that's supporting is then going to give way to the pressure and then just kind of
let it fall over so as this one pushes down my left hand kind of gives out to ensure that this
doesn't mushroom out too much just by doing that you can see that it is already starting
to mushroom out there's an overhang so I can take my sponge in my right hand and apply downwards
pressure and then push that down and into the back then I just repeat that same method until
I get this to the width and the thickness that I want so if you are left-handed or you rather use
your left hand same thing you can push down with both hands if you want to and you're just bringing
it towards your body you can have a sponge in your hand too so you can squeeze that as the clay
gets dry and then the benefit of using two hands is as you get closer to the edge you then tilt
your hand up and let that then compress the side so you just keep repeating push and slowly bring
your hand out so I think that's the easier method if you are trying this for the first time hold
your hands together and then compress and bring your hands out so this is called the hammer
compression and you're just doing this until you get this completely flat so right now I have a
mound here so I'm going to continue pushing this time I'm using my right hand to push
and slowly bring it out so I'm going to stop right here so you can see this little crater that's
developing and basically this is acting like a wave you're pushing down and as you pull towards
your body it's having the clay lift and rise up like this is the wave forming so I keep bringing
it further and further towards me that wave of clay is going to get taller and taller if I don't
compress it down so it's really important as you bring that wave of clay closer to your body
you are compressing it down into the board so it doesn't basically flare up and crash over itself
now thickness thickness of the clay that I like for a platter to get the most of the clay
is you want to go about half an inch thick if you go any thinner you can't really trim a foot
and the piece may lift up and warp if you go any thicker you can make a tall foot but your piece
would be kind of narrow because a lot of the clay you're going to trim away I think half an inch is
that good medium so just really feel the clay as you go go out you don't want it to rise and fall
and you're just making this really beautiful disc you can then bring in a rib if you want to
further compress so you have this wooden rib and then on the center here you don't want to
compress directly in the center because the rotation of the wheel is going to rotate this
and of course I'm getting crumbs on this so you want to place it off of the center so at
the right of the center at three o'clock and apply light downwards pressure and then what I do is I
push down and I slowly lift it up and I slide it outwards you can really feel where the clay is
high or low and it does take away some of the layers of the clay mostly the slip so you can
pull that off and put to the side and then you can check for thickness we'll grab the needle and then
see how thick it is and if the clay is too thick we will thin it out a little more so I got my
needle let's go ahead and check the thickness stab it in and pull so we are a little more than
half an inch so I can go a little thinner and that will allow me to make a bigger piece
and not have to trim as much so it's really up to you and how thick you want to get this
so we'll continue that hammer push push down so just by pushing you already see that in-depth
forming and pull towards your body or if you rather see the movement you can push down with
the sponge and then slowly slide the sponge outwards towards the real clock or pull it towards you
but I do prefer your fist because this is easier to control and it covers a little more surface area
than the sponge but see which one works best for you just make sure that if you do that have the
sponge in your other hand so you can easily apply moisture as needed and then now I can feel it
rise and fall there's a high spot here so I'm going to go back and then compress as needed with
the sponge so I'm really feeling the clay and so you must be wondering how am I going to transform
this disc into the platter over here and so what you're going to do is you're going to take your
clay and we're going to start pushing the clay on the side here to make this rise up so we're kind
of doing it in inverse or reverse so we establish the base and then we work on the wall normally we
dig and then pull out to create the wall but this time it's a little different and so one cool thing
about this technique is if your outside is not perfectly centered what you can do mine is
decently centered but pretend like it's off-center you then take your needle and then you drop it
down on the outermost edge of the clay and you do it all the way down until you hit the board
and once you hit the board you can cut away that strip of clay that's not even and hopefully if
you ever do this it's you do it better than me and not let it go halfway and what is left is
a perfectly centered disc of clay and so it's really important to make this outermost edge as
centered as possible because as we're pushing it inward to make the clay rise up like that wave
if it's uneven it's going to rise more in the part that has more clay so really important to
even it out and i haven't thrown in a while so i'm really messy today anyway so we're gonna take
this clay now to make this bump up and rise in my other video we got a wooden knife we cut
underneath and we lifted it up i'm not a fan of that i rather use the sponge and compression
so i take your sponge at three o'clock you're going to gently wrap the sponge over the edge so
one finger will be on the disc another finger will be on the side where the board meets the
disc and we're going to use our hands like this and push it inward kind of like it if you ever
play with the tech deck and you have your fingers like that riding it it's gonna be like this your
middle finger the finger on the farthermost outside is going to be pushing in to look
something like this so i'm going to switch sponges so it's easier to see i got these
smaller sponges that i just cut these ones in half anyway place it on top now my middle finger
is going to be pushing the most and that is causing the clay to rise up my pointer finger
here just is compressing the clay down a little bit so that as the clay goes inward it rises up
and my pointer finger that's pushing down it's making sure that it stays compact and i just keep
doing that until i get the clay to either the width i want the bottom to be or enough clay here
where i can then play and lift and pull so this part is all about personal preference i like
getting this to about an inch tall by inch thick that gives me a good amount of clay to work with
so once again drape it over and now that it's taller i can actually just put my pointer finger
on out here my left hand is doing the compression down and it's moving it inward so the sponge is
wrapped over this clay and you can see that it's starting to turn back into a plate more or less
and so if i wanted a plate this is basically set up where i just thin this out pull it a little
bit and flare but i'm making a platter so i want this a little taller a little thicker so i'm just
going to keep going okay a little more beefy and the more i push inward with my middle finger here
the thicker it's going to get and so base wise i want this to be able to eight inches wide so we're
pretty close because from my pinky to my thumb it's about eight inches i'm going to go a little
more almost seven and a half that way i have more clay to play with and there we go i got my clay
relatively thick here it did thicken up a little bit on the base so i could go thinner here but
we'll leave it for now and so now this is set up to pull my walls up so when we pull this is
basically the same way we pull like we always do compress the clay between our fingers and lift up
whether you do it with the sponge the knuckle the pitch and pull it's really up to you but for
something that's kind of tiny like this i prefer the sponge and my pointer finger side of my finger
side of my finger against the sponge and just compressing so like this pressing like that now
as i compress to the left and the right you can see the clay start rising and so i don't want to
push this bottom section inward anymore i want to start lifting it up to get a clay wall to then
flare it to create the platter so as i lift up as always release the pressure when i get about
this high so right at the top i release the pressure and i let my fingers kind of just
catch up i let the clay catch up to my fingers and then we're going to go ahead and compress the lip
here and then thickness of your rim because i'm going to flare this out even more you want to
make sure that your rim is not too thin i say a good three eighths of an inch to a half inch thick
is perfect so i'm actually going to compress this down a little more to closer to half an inch
and then i'm going to go ahead and do another pull so this time when i pull i'm going to pull
and shape to start creating the curve and that way i can start establishing this nice inner curve
and really feel the clay wall and so this time i'm going to push this bottom in a little more
to create an undercut and i'm going to push outwards with my left finger to start creating
this bump out so this little undercut here is basically establishing where my foot's going to
go when i trim and this bumps the clay up my left finger is pushing the clay out and then i can
actually start doing a pull where i'm pulling out diagonally and then right around here i start
releasing the pressure and i'm going to keep the rim more or less that thick because i'm still
going to stretch it out a little more and i don't want it to thin out too much okay so let's feel
for thickness again i can do another pull i'm not going to push in too much at the base this time
it's kind of compressing here a little more a little above the base and i'm going to add a
little more volume so this pull that i just did was a shaping pull so i compressed and i kind of
went out and then up so i'm liking the shape so far i'm going to compress the lip a little bit
round this out because it is getting a little too wide a little too triangular at the top and then
i'm going to bring in my rib and of course it's all crusty so go ahead and rinse that and i'm
going to add a little bit of roundness to this checking for size we're about nine inches wide
and a little over two inches so i'm going to flare this out a little more and it's going
to shrink in height a little bit and so i'm using the curve of this tool to match the inside of the
piece or actually the curve of the tool is going to then form the piece so this curve initially
bottom section is pushing out the clay wall so everything against the clay is touching the
wooden rib and we're going to go ahead and start from this side now i'm going to work on this
transition right here kind of remove anything that's not needed and slowly work my way up the
clay wall and then stop when i get to the rib all right size wise we're about two inches tall
about what am i doing i'm just going to use the ruler so we're about nine and three quarters
wide by two inches tall this is going to shrink a little bit and i am more or less happy with
this shape so i'm just going to get the sponge i'm going to kind of feel the inside it feels
pretty compressed the transition feels nice and gentle so i just to be safe i'm going to compress
this middle a little more so using this tool now apply pressure and then slowly bring it out
and then on this outer edge i'm going to rotate it so it's a little less dramatic
and i'm going to work that transition up the side and then soften this transition line here
so it's kind of like trimming so it's usually best to compress before you do the final shaping
because it may mess up your transition from floor to wall and it's kind of hard to fix sometimes
without trimming it all right and if i play with this anymore it's probably going to collapse
because this part this angle is pretty dramatic and so the last thing i'm going to get my gross
little chamois that's really dry and crusty get that nice and hydrated we're going to round the
rim soften it and then we're going to move on to the second way to make a platter all right
there we go we'll create the little groove at the base and wire it off if you're enjoying these
videos please don't forget to like and subscribe that way it helps to grow this little channel
and you can see the videos being released every week all right there we go let's pop this off
and get our second piece all right got our second three pound piece of clay let's go ahead
and get this started so that first method is the slightly easier way to make plates or platters
and that's just compressing the whole thing into a disc now this next method is the method that my
teacher in high school taught and the reason why i've never made plates in high school
was because this technique just looked way too difficult to understand and you kind of you'll
see what i mean once i start developing it but setup is always the same so cone up cone down
get it centered and this time we're not going to flatten it into a disc we're going to basically
get our mound like how we normally would if we're throwing a bowl or a vase and we are just going
this one is about five inches wide a little more narrow than a normal piece and then we'll dig our
well to that same thickness that we're aiming for so that half inch thickness okay we're going to
go ahead and open our well and then right around here once we get our inside wall vertical
we are actually going to start pulling this clay outwards and so as i do this
you're basically transforming this donut into a flat disc by pulling the clay and compressing
it down at the same time and so the reason why this was so hard to understand was because as i
tried to try to myself in high school and i pulled i would always not compress down enough to then
get it back to the board and so when you guys do this do it slowly and i do recommend trying to get
any water off the board or at least thick slip off the board first make sure you don't have any skirt
and the method for this you basically are putting your first hand left or right doesn't matter
on the clay so that this part is compressing down and then your other hand is on top of that hand
and this will be pushing down as well so both hands are pushing down once you feel the clay
compress then you're pulling towards you to then lay this down basically flatten this into the
board so i'm actually going to change position so i'm going to be moving to here so that this
would be my midnight so it'd be easier to see how it flows outwards as i'm doing this compression
so i shifted my body this is my midnight right here and i'm going to be compressing down and
pulling towards me so you can see how the clay kind of just lays down into itself here so once
again left hand to drape down over the top for the purpose of this demo i'm going to use my right hand
so you can see how this falls and my left hand is going to be on top normally i use my left but like
i said you can use both hands and then i like putting the sponge in either hand so that this
can then squeeze as the clay gets dry okay so i'll put on my right and then my right hand you
can see start compressing down add water as needed and then you can see that the clay is compressing
down it's looking more and more like a big donut so i'm going to add a little more water
compress down a little more and at this point now the clay is basically flattening out
and then reattaching to the board and so to get the rest of this i'm going to now pull this clay
outwards by using my pointer finger and my middle finger my right hand and pulling that clay out
towards me and i'm going to compress this spot again of my hand as i'm pulling it out
so you can see right here this is where the compression is occurring this i'm going to hold
in my left hand so left hand sponge is touching this to get lubricated and my right hand is
compressing down so changing the way i'm holding it and the compression is still more or less the
same okay and then because my bottom didn't flatten out completely like how i wanted to
i'll go back and then do the hammer to then flatten that out so that way you flatten it
by compressing and pulling so i'm going to get this back into a mound so that you can see that
all in one go rather than me breaking it down in multiple steps so let's get this back into a
bigger mound all right i got it back to the shape that it was before i started the compression
let's soak up the water okay now i'm going to do that whole process again
in one motion so you can see how fast this can be for the technique so i'm just going to flatten
this bottom section a little more because it got a little thick when i recompressed it
went a little thinner all right so this time i want to do the same compression but i'm going
to drape the sponge over the wall to help keep it lubricated because i had to keep adding water
so here we go you can see that's my left hand right hand on top compress down my pinky is
engaging and squeezing this edge so as i compress both hands are pushing down and now i'm pulling
towards me to bring this clay wall outwards right around there i'm gonna stop you can see how much
faster that was and then to get this clay wall to get this base completely flat again i can just
use a sponge to really drive that clay outwards get it back to one big chunky part here compress
this just like how i did the first plate by pushing from the outside to get that clay wall
thicker and then thickness wise we want that seven and a half inch width so i went a little too far
so let's compress this down a little bit push this in a little more and there we go and like i said
because this wasn't completely flat from my compressions we're gonna go and grab the rib
and compress it now so off the center compress down flatten that one more time there we go
nice and flat and now let's go ahead and pull and shape get rid of that skirt add some water
this i'm squeezing the clay with my right hand here and i'm lifting so it flared out a little
bit already that was the first pull compress make sure it's nice and flat still there we go
and now the shape and pull at the same time so pushing at the base push out from the inside
and then start pulling up and getting that roundness all right there we go release the
pressure look at the sizing and let's get that ruler again and size wise it was nine and three
quarters so pretty much on the dot height about two inches so we basically got the shape in two
pulls this time now i'm just going to refine it add a little more volume to the outside
using the rib and now this this is all extra you don't need to do this it's more personal
preference i just want it more rounded especially because i did a little more on the other one
so supporting the bottom here because i know if i push too much downwards with my inside hand it
may collapse on itself i'm going to thin the rim out just a tad bit all right i think that looks
pretty good there's a slight bump here in the transition section so let's compress that
smooth and then shammy to compress and this rim is a little thicker and i prefer slightly
thicker rims like this so i'm definitely liking the way this is thrown over the first one
and of course create the groove at the base and let's get this wired off and wrap up the video
and there we have it two ways to make platters or plates if you wanted to one slightly easier
takes a little longer and one slightly harder but it's much faster so let me know in the comments
below which one that you like better which one you think you're going to want to try out
and in the videos to come i'm going to show you guys how i like trimming these guys
two different styles of course so one the traditional way on trimming so you get a nice
big wide foot and another one for extra support if you're a little worried about the middle slumping
so that we have this inner part to then ensure that this stays flat and we're going to round out
this short series with how i like glazing these bigger pieces so if that's something that you
folks want to see don't forget to like and subscribe so you can see those videos when
they are released every week and of course i want to give a big mahalo to the mud club members
and a shout out to the mud club plus plus plus members we have jj kiss michelle xu and james
oats and once again for the mud club plus plus plus send me an email or reach out on social media
so i can start sending you guys all of the perks that you guys have unlocked in that tier and
hopefully i see you folks in the next video as members as well
so until then thank you for watching and i'll see you folks in the next video
