Clock Repair for the beginner course part 5

Chrono Chronicles
8 followers
3 Video Views·May 3, 2026
Clock repair part 5 in the series to learn clock repair. These are for the beginner who want to learn to repair clocks. This video is a small part of the full 4.5 hour clock repair beginner course.
Today we're going to be using this Seth Thomas clock here for all our demonstrations and
repairs and cleaning and maintenance that we're going to be doing throughout this video.
But before we get into removing the hands from the dial, I do want to mention one thing
is that the area and surface that you're using and the proper lighting that you're using
in order to do your repairs, you should use as large of a surface as possible that you
can find.
A large table, a large workbench, something of that nature, or a kitchen table if you
have to do that.
On the surface, I'm using here an actual beach towel because, and it's white, because I can
see all the parts if they fall down, like if this little screw falls down.
And on this type of surface, it won't roll off the table and I'll be looking all over
the floor for the screw or the nut.
So this type of surface prevents things from rolling off and also you can find your items
as they fall, if they happen to fall as you're doing your repairs.
So this type of surface is really important and I highly recommend using either, or else
you can use a felt surface too, also works very well.
Another thing is lighting.
I use these adjustable lamps like this and they're very handy because you can get up
and get around and underneath and beside and I always use two because you can have one
on one side and one on the other side focusing in on something and two always works better
than one.
Just like they say, two heads are better than one, two lamps are better than one.
So I highly recommend that you use two lamps.
Today, now we're going to talk about removing the hands from the dial and so we'll zoom
up on to this little clock here and this is what we're going to be using today to demonstrate.
I'll adjust the lighting here a little bit so we get a good clear picture.
One thing you want to do before you get into clock repair is make sure that the hands are
not rubbing against each other, that there's enough clearance between the hands, between
the minute hand and the hour hand so that they're not rubbing each other or rubbing
each other as they pass.
A clock will actually stop because hands can't pass each other because they're touching each
other or they may be touching the dial or they may be touching the glass.
If you close your bezel and it touches or it hits the minute hand, which is usually
the first hand that sticks out from the arbor, that can slow down or stop the clock, especially
if your movement's not very strong due to a lot of dirt.
So you need to make sure there's enough clearance between the hands.
Some hands are removed by way of a screw, there's a screw right on the end here and
some are removed by way of a pin.
This one has a pin, it's called a taper pin, that holds the hands on here.
So the way you want to remove the taper pin is you can either grip it from the bottom
and pull it out or you can put your bottom of your pliers on the bottom of the arbor,
put your other hand of the pliers on the top and then just press down and as you can see
that forced the pin down and you can, with a little gentleness, pull it out the bottom.
Now if you have some stubborn hands that won't come off, I always remove mine by hand, use
my fingers, you can use what's called a hand remover.
A hand remover looks like this.
Here's a picture of a hand remover.
Now the way this nifty little tool works is these little edges here go underneath the
hands, which would be like right underneath here and as you turn the screw and the screw
comes down, it'll hit the minute arbor right there, therefore forcing the hands forward
this way and removing them from the minute arbor.
Now these are really nifty little tools and they can be picked up for I think less than
$10 at most of your clock suppliers, but I don't even own one because I always remove
mine by hand.
I usually reach in there with my fingertips or if I need to, with fingernails.
So first you take off the minute hands and that came off pretty easily and there's little
washers here that were in front of that, so you have the taper pin, the washers and then
the minute hand right behind it.
Now the hour hand, it's held on by a steel split bushing, which is on over the cannon
tube of the hour arbor and sometimes they're a little bit stubborn.
That one popped off, so fortunately I was able to get these off my hands pretty easily.
Now as far as cleaning these hands, the best thing to do is to use like a formula 409 and
just wipe them off with a towel and clean them up and they'll look really good.
I wouldn't repaint them, that's not my preference, I like to keep the original patina, the original
aged look and just a little formula 409 or just a little soap and water and wipe them
off and dry them carefully so that they're fully dry to avoid any rust.
