I Restored Some Art Deco Furniture - Was It Worth It?

Trash To Treasure
3 followers
Water stains, oil stains, and flaking, oh my! I bought these pretty rough vintage "night tables" from FB marketplace. But these are actually the two pedestals of a vanity that was disassembled at one point. There are a ton of finish issues; there's no denying this needs a full refinish.
I needed to fully strip these, patch some veneer, get rid of the water stains, stain, tone, seal, and polish. But nearly a week later, these are UNBELIEVABLE!
______________________
#furnitureflip #refinishing #furniturerestoration #antiquefurniture #vintagefurniture #transcendfurnituregallery #diy #furnituremakeover #furniturerepair #furnitureflipping #artdecofurniture
Hello everybody and welcome to another video. Today I'm going to be trying to save these walnut
art deco side tables that I found on Facebook Marketplace, but these aren't actually technically
side tables. These were part of a vanity and for once you can't get mad at me for doing it.
I purchased these already taken apart. They need a lot of love, so stay tuned as I try to
bring these beauties back. My name is Angie and I refinish furniture. Sometimes I paint
and sometimes I don't, but I always do what I can to save old pieces from the trash.
Welcome to my workroom. These sort of transformations are always subjective. I
always have people that get angry when vanities are taken apart. It really depends on the piece
itself and where you live, but around here vanities do not sell very well and a lot of
these end up in the trash. Night tables on the other hand are hard to find, especially decent
quality ones, so sometimes it just makes sense to do this. Like I said, I purchased this already
disassembled and these had clearly been used as nightstands for quite a while.
I'm going to start this process by removing the drawers and marking where each drawer belongs.
The drawer faces have really beautiful veneer on them and because they're bookmatched these
drawers really do belong in certain slots. I'm not really sure what happened in this drawer,
but there's some pretty significant staining there that I'm a bit concerned about.
We'll have to hit that with a sander and some oxalic acid and see what we can do.
Having a look at the drawer faces themselves, you can see especially around the edges of the
handles each of these drawers has slightly different damage from the handles. A lot of
them were loose and when I went to remove the screws I had a really hard time with several of
them. You can see it's coming out very strangely here and it's just because a lot of the machine
screws were actually bent at the end. So any that were bent will get replaced with new ones.
And I have my little shop helper here, Nacho, was making sure things were going smoothly in
the beginning. So the outside of each piece is completely fine. This is the inside and this is
where the shelf of the vanity would have attached and then the little board at the bottom. There's
some holes there, some residual glue I'm gonna have to clean up, and you notice the edge here
is a lot darker. This is actually a different type of wood that runs along the inside of the
frame and then they've got the walnut veneer on top of that as well as on the sides. And if I flip
this piece on its back and kind of peek up underneath you can see here that there is a
different veneer on the underside which sandwiches the frame piece which is stained very dark here
and then the walnut veneer again like I said on the outside. If I flip this right over this is
kind of cool you can see how they created these rounded corners to begin with where they just cut
a series of slices basically in the wood and it allows it to bend and make this corner.
They also have a different type of veneer on the inside of the sides. The drawer faces are also
walnut veneer but they have beautiful figure and they're bookmatched which means basically there's
a line down the center and each side is a mirror image of the other. And like I mentioned a lot of
them have damage from the handles. While the drawer faces are solid wood they are not solid walnut as
you can see here. I'm not 100% sure what the finish is so I'm going to try removing it with
some methyl hydrate first. If this is a shellac based finish which a lot of them were back in
this time this will turn the finish gummy and I can either scrape it off or scrub it off with
the steel wool and I'm using very fine steel wool. This reaction would happen quite quickly
so generally if nothing's happened after about 20 seconds I can quite confidently say that this is
not a shellac based finish and as you can see here there's some dirt coming off but none of the finish
and even using a little plastic scraper here there's just nothing coming off really except
for what I just put on. So it's safe to conclude that this is not shellac so my next guess would
be lacquer. Lacquer gets dissolved with lacquer thinner and if this was a lacquer based finish the
same thing would happen. I would apply this and it would become a bit gummy but again nothing
was really happening or at least quickly. After some scrubbing this did eventually come off enough
where I could just hand sand it but now I know that it will make more sense for me to use a
chemical stripper on the rest of the piece. If I apply just a little bit of mineral spirits here
you can see how beautiful that wood grain is underneath. Now I do not know what happened here
to this drawer. It looks like it could be an ink stain but whatever it is I know that it's not
going to be easy to remove if I can even remove it at all. I'm going to be trying a few different
methods to lighten this. Initially I tried some methyl hydrate that didn't work so I just tried
some stripper. Sometimes that will loosen certain stains. I got a little bit of the color off but
not much so I decided to just let that dry out temporarily when I went and sanded the drawer
boxes. Pretty much all of the veneer I'm going to be hand sanding but I'm using my surf prep here to
make quick work of these drawers. I'm using my favorite stripper here which is circa 1850. It's
methylene chloride free and it doesn't require neutralizing which is really nice. I typically
just apply it with a chip brush and let it sit. Normally I don't have an issue with it drying out
but I got distracted by doing a couple other things at the same time. So you can see here
it's a little bit dry so all I did is I just I scraped this off and then I went into another
very light coat and that was fine. So just like that strip that is at the top this base is not
walnut. I'm not 100% sure what type of wood it is but it's a very light wood and you can see here
there would be if I left it natural quite a contrast and I don't mind the reddish brown walnut
with the sort of yellowish lighter wood but it was at this point that I started thinking about what
I could do to the base. I could paint the base, I could leave it natural like this, I could stain it
and what I ended up opting to do is keep the contrast that it had before. So as long as I can
get the walnut veneer to a point where I can just put a clear coat on it that would be great and
then I can use a darker stain, maybe some toners to try to get a nice contrast with this lighter
wood here on the base. But first I need to finish stripping both of the carcasses here and the
drawer faces, fill in some holes, do some veneer patching, sanding and even though these aren't
that big they did take quite a while. When it came time to do the tops I decided to scrape instead
of using a stripper. It's a nice flat area and I knew that it would scrape off pretty well and
this particular top is the worst of the two and there's a couple of different reasons for that.
First of all there are a couple water stains but there's also a big oil stain here and as I'm
stripping this off and having a good look I think I'm starting to understand what would have happened
here. Most of the finish on this top was not intact. What I think happened is someone used
either some sort of oil or a product like Restore Finish over the whole top to try to
get this top looking better. The problem when you do that on finish that's not intact is that the
oil or the product will seep down into the wood grain that is exposed and often stain it. And you
can see here on the other top that was not a problem at all. They very well may have used the
product but because the finish was still intact it didn't have that same oil staining everywhere.
This top had a different issue. It had a little dented area right in the middle so I'll have to
address that. I'm going to be using oxalic acid to try to minimize the damage to the tops.
Here is a really good example of why certain oils over finish that's not intact is so difficult to
restore later on. I'm hoping this comes through okay on the camera but you can see as I'm brushing
the oxalic acid over top it's immediately fish eyeing and resisting. All over the top of this
one particular piece I'm getting fish eye and that is from oils that have penetrated in certain areas
on the piece. There's technically two types of furniture oils. There is drying oils and non-drying
oils and while some oils and waxes can actually help preserve a piece some just make it harder
down the road. So this is after the first coat of oxalic acid has dried. It hasn't been rinsed off
yet but it's dried and you can still see a fair bit on the worst top of the water staining and
again that oil stain is still there. The other top turned out pretty good after one coat but because
I need to do a second coat of oxalic on the bad top I'm going to do it also on the good top.
Having a look here this was the problem top you can see several areas where there are still
staining visible. If I was putting a stain on this this might not be too bad but I don't want
to stain it I want to just put a clear finish on it. So I'm going to go ahead let this dry
and then apply one more coat of oxalic acid. Generally if a stain is not gone by the time
the second coat is over with it's not going to come out. So fingers crossed. Oxalic acid needs
to be completely removed with water so I'm just using a rag soaked in water and I'll do that a
couple of times until I'm sure that it's all gone and then let it dry out completely. Okay so here's
where we are after two coats of oxalic everything's dried and rinsed you can see that bloody oil stain
is just still there. I'm gonna go ahead and sand with 180 grit sandpaper and then I'm going to
address this little depressed area here on the other nightstand. Normally for something like
this I would use the edge of a hot iron but a viewer actually sent me this from my Amazon wish
list and I'm finally able to use it in a video. This is a little soldering iron and it comes with
multiple tips. So I'm picking the one that is the closest to the width of this depressed area
and basically what I'm going to do is use some water and heat very concentrated to try to steam
the dent out. Now this doesn't work all the time sometimes it works amazing sometimes it just
doesn't work at all. It took about 10 minutes and I think this is about as good as I'm going to get
it. It just it raised to a certain point and then it just stopped raising so that's where I need to
stop. I'm okay with it though it's way better than it was. It was this one random nail sticking
out here of the side of one of the pieces and these are such a bugger to get out without damaging
the veneer so I'm trying to be very careful here. I added some walnut wood filler here where all the
holes were. I'm now ready to sand the sides. I'm going to be hand sanding this. I could use a power
sander including my surf prep but these rounded edges are so delicate that whenever I have any
sort of waterfall style furniture I really like to hand sand. If you remove the finish beforehand
either by scraping or stripping this part's really not that bad. I'm using a 150 grit sand pad here
and I'll do another light sanding with 180. Yes this is a lot of work and this is absolutely a
While this art deco style isn't necessarily rare they are getting harder to find in a condition
that can be restored. Like I said in the beginning vanities don't usually sell that well around here
it may be different in other parts of the world but so many of them get thrown out so even though
this wasn't intact when I bought it I still want to do what I can to bring this back. I think the
wood grain is absolutely beautiful and the drawer faces as well as the cabinet itself but I still
have a lot of work to do before I can put my top coat on. I'm opting to use a water-based stain for
the base and that little piece of trim at the top that was initially dark. I'm taping off all of the
areas here so that I don't get stain on the rest of the piece and then once I'm taped up and ready
to go I just grabbed a little rag here and while normally you would wipe on the stain and immediately
wipe it back I'm actually not wiping very much of it off I'm letting it dry and then doing
subsequent coats. This is going to give me a much darker base and with a water-based stain
it dries really quickly and it's easy to do this technique. This isn't going to be the final colour
though this is just a base coat. Once I have all of the trim stained I'm going to let it dry and
work on some repairs before coming back to it. This hide glue actually needs to be warm before it's
used so I usually just do a little dip in a warm bath for a couple of minutes and it softens
enough to be able to be used. One of these drawers needs a little bit of attention here on the back
you can see that it is separated from the side and the glue block is not connected anymore
and when I popped the glue block off I could see why that was happening. The veneer that they put
on the back of the drawer front has this almost like a paper tape on it and the glue block ran
right over top of the paper tape so it was only glued to the paper and not the wood itself so
it didn't get a very good bond hold apart so I just need to scrape that paper off and re-glue this.
Now I have to address this chip on one of the top drawers. You can see the different layers here
we've got the solid wood drawer face and then we have a layer of veneer which is the substrate
and then this beautiful burled walnut on the top. In order to replace the top layer of veneer I also
have to replace this missing part here on the substrate. So I'm heading into one of my veneer
drawers and looking to see if I have any walnut burl or something that would work and these two
are beautiful for sure but they're not quite the right pattern. This piece isn't either but it does
have some areas that could possibly work. Now when I mentioned earlier about book matching this is a
perfect example. Whenever you see on a drawer face or on the front or side of a piece a pattern
that looks to be a mirror image this is almost well it is always veneer and they call it book
matching. So because this drawer front is book matched I need to find a patch with grain that
is similar in direction and color to the opposite side and I think I did find a little spot here.
Now I have this tool for paper crafting but a few days ago it dawned on me that this might
make a great cutter for veneer so I'm going to give it a try here. It's just a little rotary
blade. That worked awesome so that may be my go-to for cutting veneer. So basically all I'm doing
is narrowing down the part that I need to use. I'll keep checking it making sure that it's going
to work and that I don't cut too much off. I've replaced little chips like this before with wood
putty and then used markers and stuff to mimic wood grain but it's always best to use real wood
grain when you can and I do have this piece of walnut burl here so I'm just going to patch it
with this. Well that was officially the most dramatic patch I ever did. So this water-based
stain has completely dried now and I need to seal it before I do anything else so I'm using some
mohawk vinyl sealer. This is going to completely seal the stain and separate it from any coloring
and top coats that I follow with. You can really see the contrast here so what I'm going to do to
replicate that is use some mohawk toner and the color I'm using is dark red walnut. Obviously I'm
trying to be careful with the overspray but even if there is a little bit that gets on I can just
do a very light sanding to remove it. These little tables are sitting on dollies as you can see there
that's why they're wobbling they're not actually unstable in any way. Once I get down to the bottom
here I'm actually going to use the same odies oil right over the stain and the vinyl sealer
and the toner. This is the part I'm the most excited about putting these on the drawer faces.
The wood grain is unbelievable and the second the odies touches it it just comes to life.
I really hope you're enjoying watching me bring these back to life but I also know that the
original look isn't always for everyone so let me know in the comments below whether you like
this flip you think I did it justice or if I should have done something a bit more modern.
Me personally I love these just as they are. Finally getting around to that one little drawer
there with the patch and you can see because it's obviously not from the same era or the same tree
it's a little bit of a different color so I'm going to need to work to blend that in a little
bit more in terms of color as well as figuring in the wood. So I'm going to be using these two
colors to sort of do a little bit of painting. I don't normally like to do this until after I've
sealed the piece because the color as you've seen changes so drastically once you put a finish on it
and the odies oil here is plenty dry this isn't going over fresh odies oil and it does stick
really well. Once this is finished though I will do one more coat of odies over this just
to make sure it's completely sealed and all I'm trying to do here is just sort of hide this patch
and try to help it blend in a bit more. Next on my seemingly never-ending list is to polish up
these handles. Now these I do believe are solid brass I am not really sure what condition they're
going to be in under here but I'm going to use some Brasso to clean them up. These don't
necessarily have to look 100% perfectly brand new I don't mind a little bit of patina but
obviously there's too much going on here right now. Now there was a step in this process that
isn't shown here on this video because I didn't realize my SD card had run out of space but
basically what that was was using some powered feed and wax on the drawer boxes so inside the
sides underneath you can see here it makes quite a big difference. I shared a picture in my community
post a couple of days ago about moving my office from the craft room downstairs to our spare
bedroom upstairs. I actually set the camera down on the desk while I was trying to fish some wires
up from behind. I had to ask for a little bit of help and help he did. I still have a bit of sound
deadening foam to put up but I'm loving this new space and it has a much better view than the wall
that I used to look at. So just a quick recap of what I used for this. I stripped everything with
circa 1850. I used timbermate wood filler to patch the little holes. I used some man water-based wood
stain in the color American Walnut. I used Mohawk Easy Vinyl Sealer and Mohawk Ultra Classic Toner
in the color Dark Red Walnut. I used Odie's Universal Oil and a 1500 grit Merkur Merlon pad
to apply it. These Mohawk graining markers, card feed and wax in the drawers, and Brasso.
This came after I filmed that last part. I decided to add just a little extra protection to the top
only using the Odie's wood butter and the wood butter differs from the Universal Oil in that
it has a higher wax content and this little smear here that I put will be enough to do this whole
one top but of course I'm applying it to both tops. I knew when I picked these up on Facebook
Marketplace that they were special but this is one of those projects that even though you could
see what they could be in the beginning at the end you're still shocked at how beautiful they
turned out. I just want to say a huge thank you for all of your support and kindness. All of your
likes and comments and shares really helps my channel out and if you like this sort of content
please consider subscribing. I try to put out three videos a month. Time to end the suspense
and show you what these two Art Deco repurposed side tables look like. Thanks for watching.
