How to Prep for TV Wall Mount Bracket

VideoJoeShows
86 followers
28 Video Views·Apr 22, 2026
https://www.youtube.com/user/VideoJoeShows
How to prep for a tv wall mount bracket will be shown & discussed on this howto video. VideoJoe is just starting his project of installing the tv wall bracket to the existing wall. He's got to line up the bracket just right & pre-drill for the bolt holes before attaching the tv wall mount bracket to the wall. Watch & learn as VideoJoeShows you how to go about getting ready to install the tv wall mounting bracket.
https://www.youtube.com/user/VideoJoeShows
Now we've got to transfer those lines, those marks up on the wall. Here's my little swivel
out bracket assembly that's going to be bolted up against the wall.
You've got to look at that on the directions, make sure you know what the top and bottom is.
And I know this is the bottom and I can flip that over and see there's screw holes here,
one there, one there, and one up here. And that's how this is going to be bolted up to the wall,
right along the stud, right in the middle of the stud. Okay, so I look at this and I know
the bottom is 69 and 3 8ths, so I just hold my tape measure,
what did I say it was? Let's see here, 69 and 3 8ths I guess it was.
I can hold this to the bottom 69 and 3 8ths, I just want to know where that next mark is.
So it looks like it's up, actually I can read the tape at 69 and 3 8ths and then go up to 70
and a quarter, 70 and a long quarter, or I could measure this up from 69 and 3 8ths up to 7 8ths.
I could mark the next two holes or I could just have the bottom here,
I can hold that up and mark it, but I want this to go nice and level, nice and plumb,
up against the wall too. So I mean there's different ways you can do it,
you know, but the main thing is we're going to bolt this right up to the center of that stud.
We've got to find the center of the stud too, so we're not done with our measurements yet.
I went ahead and marked this and all that, but I'm just going to kind of
go through the motions with you. I went up, I went to 69 and 3 8ths and I put myself a mark there,
then I had to figure out about where the center of that stud was, and I came over
and put a mark there, then I had to start probing with some nails,
that's what these two little nail marks were, you know, and I didn't want to make
that too close to where the hole was, so I just started tapping in here
to make sure I could hit the stud. I wanted to make sure once I hit the stud,
I went over at a little bit of an angle this way, and then I started over here and went that way,
so I could know about where the outside edge of the stud is here and over there,
because the last thing I want is if I put the nail straight in, if I hit the stud, okay,
there's the stud, no problem, but you've got to make sure you drill your holes in the center of
that stud. You don't want to be on the edge of a stud and then put a mark up there and say,
oh that's fine, the stud's an inch and a half wide, what's the problem? You've got to find
the middle of the stud, and that's what I did. I put a mark down there,
and I came up from the bottom, and well, first I put the mark, and then I got my level up here
and ran that. I wanted to make sure I was going up nice and plumb, and I put a pencil mark on there
and all that, and I put a pencil line there, and I also had to measure the bracket because I didn't
want the pencil line to go up above the bracket, because that wouldn't show on the wall when I got
all done. Then I transferred my whole pattern up there and did all that. I got a scratch all like
this, and I put it right in the middle there, tapped on there to get my little marks, and I
drilled holes there. You have to, before you drill those holes, see those holes are for these lag
bolts. A lag bolt that goes in there, and you've got to do a pilot hole in there first, so I just
looked at the directions and got the corresponding drill bit size that I needed, and then I drilled
that, because the last thing you want is to get a drill bit just, you know, you think you know
which one it is, you put one too big in there, you draw three of your holes, and now these, once you
put these in, they spin or something, or I mean, I'd rather have a smaller hole first and try one. If
it's too hard, take it out, do another pilot hole, but you know, with the same pilot hole, but a bigger
drill bit, but I didn't do that this time because I read the directions, looked at there, and it told me
which drill bit size to use, so that's what I did, and now we're ready for the next step.
Before I take my bracket up there, I got that drilled, I just wanted to put this in here,
I wanted to make sure it was right, so I got my ratchet set, and I got to go through the sheet
rock, and it almost seems like they put two layers of sheet rock here, or something, because it
was thicker than half inch, usually your sheet rock is either half inch or five eighths on the wall,
and this might have been two layers for some reason, but anyways, the bolts are very long,
and so I'm just going to get a hole, get this down in there all the way,
just so when I get ready to hold the bracket up there, these bolts are going to go in nice and easy,
okay, got to have a ratchet set for this, you don't need a real expensive ratchet set, just
a cheapo one, you do that on all your holes, that way it's going to go in nice and easy,
make sure you, you know, you don't want to hit a knot or something, and mess with it as you're
trying to hold the bracket up there, and the bracket slides, and scratches your wall, and all that,
you know what I mean, okay, have I showed you something so far that you don't think you can do,
you can do this, come on, I know you can do this, you just follow these steps, I don't want you
being afraid of your project, you've never done this before, that's okay, I think you still can do it,
you don't think you can do it, you know, you can get a friend over to look at the video,
and have, show it to him, and he can help you, all kinds of things you can do to do your project,
I don't want you spinning an arm and a leg to pay somebody to come over here,
and put this tv up for you, because you know what, once you put up one tv, you're going to say, oh,
I want to do that down in the den, I want to do that in the spare bedroom, in the
family room, whatever, most people have more than one tv, and nowadays,
people are putting them up on the walls, if you can do one, you can do all of them.
