How To Shave Your AR-15/AR-10 Front Sight To A Low Profile Gas Block (HD)

Uniform & Arms
3 followers
3 Video Views·Apr 12, 2026
Just a quick 'how to' for shaving down an AR front sight so it can be used as a low profile gas block under a free float rail.
Welcome back everyone. In today's how-to video we're going to go over how to shave down your
front sight post to add a free foot rail. We're going to go from something like this to something
that looks like this. If you guys, I'm not sure how well you can see underneath there in that
alpha rail but that is a just a shaved down front sight post and we'll show you how it's done today.
So as you can see there we got the front sight in the vise nice and tight. I'm gonna go ahead
and cut the bayonet lug off first and then this sling swivel point and that's what we'll go from
there. So as you can see there we ground the bayonet lug off now we're just going to grind
the sling swivel off the same way. Again you want to make sure you leave the enough room here on the
bottom for where your pins are going to go your tapered pins. So we cut through this side I went
ahead and turned it around to go through that side so that way the sling swivel is not just
hammering against your blade which it wasn't for me so that's what we do just flip it around there.
Next up we're going to cut off the front sight post here itself you want to make sure you don't
really go anywhere beneath the top of the gas tube there. So this is going to be our little
starting point we'll round it off after that but we're just going to cut off above the gas tube.
I'm going to go ahead and actually just mark some reference points on the outside here
I'm not sure if you guys can see those but that way it'll help me when I'm cutting through just
to know make sure I'm not cutting too much off. Probably not necessary but better safe than sorry
and you can always remove more material but you can't add it back on so there you go we'll get
to cutting here. As you can see there we got through the front part of the front sight we're
going to do the back now same thing and we got the whole thing off we're going to pull it out now and
take it over to the grinding bench. All right so what I'm going to do here is I'm actually going
to grind this stuff down take all these sharp edges off here on the bottom the reason I'm using
the towel is obviously it's going to get really hot but what you want to be aware of is you
generally don't want to go grinding down too much right around where those those pins are going to
go in because that could throw off the tension on them so basically that's kind of like our starting
and stopping our stopping point excuse me for grinding so I'm going to go ahead go over here
on the grinder and start working it down and see what that's like. There you go guys you can kind
of see how it's working out you see it's smoothing out already go ahead and finish off this one and
we'll talk about this one. Here's what this end looks like after we finished up with it
you can see there it pretty much has the profile if you ever look at a low profile
gas block that's pretty much the profile it has and that's kind of what you want to go for you
can see you left the pins intact there so that way we'll still be able to use them the holes for the
pins I should say we'll go ahead and do the same up here on the front as well as grind that out
and then we'll talk about the top. All right so you can take a look here at the bottom of it
see how that looks that's pretty much how we're going to leave it so that way the rails will still
be able to go on over it's nice and low but it still has enough room where it'll be it'll be a
sturdy little gas block still anyway what we're going to do now is we're going to take the top
start doing the same grind down so that way we're just above the tube here so that's what's up next
so this is the point we've ground it down to on a lot of rails that would be perfect and you
wouldn't have to take any more but we're going to be using the troy rail so the troy rail that you
guys saw earlier in the video is very very low profile as are a lot of the newer rails like the
midwest industries gen 2 etc so for those you really want to make sure you get down there make
it really really low profile and in fact you probably want to take a little bit off the top
the gas block or the gas tube which is exactly what we're going to do here next but just keep
keep grinding it down until we get there and i'll show you the next stop so you can take a look there
at what we ground it down to right where you basically just start taking some of that material
off the top that's uh where we're going to stop the troy rail that should be plenty for it we're
going to do the exact same thing to this rear portion and uh i'll show you the rest of it after
that once you've got it ground down to the point that you're happy with it and that's where you
roll with it what you got to do now is either refinish it or glue it or spray paint it or
whatever if you're going to use a spray paint i recommend you use some sort of engine um paint
like that high temp engine paint because this thing is going to get smoking hot but what i'm
doing here is just using a little bit of alcohol rubbing alcohol and i clean up the surfaces there
because i'm going to be using a uh instant blue cold blue perma blue i'm sorry i'm saying the
to redo it but again it's not necessary you absolutely can use just high temp
engine paint or whatever you'd like to do that as you can see there we're using the
birchwood kc perma blue and uh basically all you're gonna do is once that's dried off from
the alcohol there's nothing on the surface no dirt no nothing just take it you can also use
a rag to do this but just apply it to any of the surfaces you want to blue um you can see there
it's already starting to take hold but um you're more likely than not gonna have to do this a
three or four more likely than not it just depends how much you really want it to be done
i mean this isn't really a high wear part or anything but you definitely want some sort of
protection over that raw steel so just keep putting it on you want to not touch the uh
parts like i just did that uh have the bluing on it and you're gonna let it sit there
for 60 seconds and all you're gonna do is rinse it with water and you're gonna repeat the process
so every 60 seconds rinse it with water dry it off you know you wipe it dry with a cloth
or you know rag whatever you have obviously not a dirty rag um and that's it so you let it sit
60 seconds i'm gonna do that a couple more times off camera and i'm gonna show you what it looks
like at the end i went ahead with the bluing process two more times and this is what we ended
up with here you can see there it's pretty even across the board but there are some spots that
kind of need to be filled in still what you're gonna do now though is i just go ahead and put
back on the barrel and as you can see that i got the pins because i'm ready to knock it in
so put it back in the barrel uh pin it in because during that process you're probably
going to nick something up maybe one little scratch here in there and i go over and reblue
the whole thing while it's on the actual rifle itself by the end of the day which you end up
with again is that uh front sight block not too sure how well you can see it there on the camera
but it is underneath that rail it is nice and shaved down you can see the rail fits over it
no problem and that way you saved yourself 30 bucks and uh in reality in my opinion anyway these
pinned front sight box are very durable probably more durable than say like a screw low low profile
gas block i mean those are pretty durable too as long as you set it right in the barrel and nipple
it anyway point is you save yourself some money do it yourself project i hope this helped you
guys out for those of you guys looking for some information on how to do it all right
thanks for watching thanks for subscribing i'll see you guys in the next video
