This is a very basic video for the brand new AR owner who doesn't know anything about the platform (we were all there once guys...). I show in detail how to break down the rifle, how to clean it, and how to lubricate it to ensure proper functioning.
Before someone says the old "I do it X way and it's way better!" --- I know there are other ways that work as well. The key is keeping the gun lubricated and relatively free of carbon to ensure proper performance.
I pretty much endorse all CLPs (with the exception of RemOil--it evaporates/runs off way too fast) for use buy use Mil-Spec CLP myself personally. Synthetic motor oils from 0w-10w seem to work well for lubrication as well. As far as greases go, I recommend a lithium based grease with a broad operating temperature range. I've used expensive 'gun' greases and found 0 difference in performance with the grease used above or the Mobil 1 brand with similar specs to the grease in the video---both work great. Almost all of the handguns you see in my reviews have this on their rails.
Welcome back everyone. What we're doing today is we're going to go over how to clean and lubricate
your AR-15 series rifle. We are not going to do a detailed clean today. We're not going to do a
white glove clean. We're going to do how I do it generally when I get back from the range and it's
just a quick cleaning and lubrication for next time. Every maybe 1,000-1,500 rounds I do a white
glove cleaning with solvents and so on and so forth but typically I don't do that and the AR
really doesn't need it contrary to what your drill sergeant might have said. But we'll get into it.
So the first thing you're going to do is obviously make sure your rifle is unloaded. So go ahead and
depress the mag release. No rounds in there. And go ahead and pull your charging handle to the rear.
Visually inspect the chamber. It is clear you're good to go. We're going to go ahead and disassemble
it and the way you do that is you're going to push the pin back here, the rear pin.
And I apologize just for those of you guys that know how to do this already. This is
going to be for the absolute beginner who doesn't know much about their AR rifle and just brought
one home. Also go ahead and push the front pin out. You don't have to do that. There are guys
that clean their rifles just like this. But I do like to get the two separate pieces. It makes it
a little bit easier. We're going to go ahead and set this aside for now. A little over. And go ahead
and pull your charging handle and that'll pull out your bolt, bolt carrier group, and your charging
handle. And we're going to go ahead and disassemble the bolt carrier group and the bolt. To do that,
take out your little retaining pin here. Just go ahead and pull it out. It'll come out. Drop your
firing pin. It'll come straight out. Push the bolt back a little bit. Turn your cam pin 90 degrees,
which is what this little pin is here. Drop that out. Pull your bolt out. You can disassemble the
by pushing this little cross pin here. You do not need to do it for every cleaning though. So
again, like I was saying, white glove cleaning, guys, I do that about every 1,000 to 1,500 rounds.
This is just a typical... I went out and shot 100 rounds at the range today. This is how I clean it.
We're going to get into what we need here. I have CLP here in a spray bottle. CLP here in a
little oiler. It's a brown ales oiler. That way you can get into the little specific areas you
want to lubricate. The only controversial thing I think I'll say today is I also have some Super
Tech lithium-based grease. I do use grease. You'll see that later in the video. There's a lot of good
gun greases out there. I've found that this stuff works just as well. I have a tube of Mobile One
grease as well. That works just fine too. This is just what I picked up when I walked out here.
I like to use a couple of these polymer toothpick looking things. You can use metal ones like this.
If you do, just go ahead and make sure that you're using a soft metal, not a hard metal. That'll
scratch into your steel. A bunch of patches or as I have here, cut up old t-shirts.
I use this Otis little wire to clean my barrel. A lot of guys use the old GI cleaning rods. That's
fine too. If that's what you're going to do, just be careful you're not damaging your bore when you
do that. That's really all you need. To go ahead and get started with the cleaning, what I do is I
spray one of the patches with some CLP. Go ahead and put it on my little wire that I'm going to
run through the barrel. The reason you do that first is that CLP or if you guys are using solvent,
that's fine too. You let that run down there and it's going to start breaking down the copper
deposits that are in your barrel as well as some of the carbon that's in there. It'll start breaking
it down and then that process will be ongoing while you're cleaning your rifle. You can go
ahead and let that process work for you. Next thing I do is I go ahead and take a spray bottle.
Go ahead and spray that CLP right into the chamber and let it sit there. You're going to let it sit
there for the same reason we're letting it sit in the barrel. It just helps break down that carbon.
I do the same here on the outside of my bolt carrier. Get in there as well where your bolt
rides. It's a chrome lined surface so that area cleans up pretty well. We're going to spray down
the outside of the bolt. You can just work that CLP around with your hands. If you're using
solvents again that's fine. Cam pin, I have enough CLP. I'm just working it around there. The firing
pin, work the CLP around there as well as on your charging handle. The last place I do is I
close my dust cover and just spray right in the upper receiver. What you're going to do now
is everywhere that you just sprayed you're going to go ahead and brush. A lot of people use a
toothbrush. This is an old cleaning AR brush. You're just going to brush that CLP around.
Spread it around. Let it start breaking down that carbon. You're going to do that all inside the
receiver, the outside of the bolt carrier, and the inside if you can get in there. Which we can
with this one, but if your brush doesn't that's fine. We'll get to that next.
On the bolt itself, spread that stuff around. Loosen up those carbon deposits
all around. Charging handle. Charging handle is really not all that important in all seriousness
in terms of being clean. Cam pin. Your firing pin. Obviously you want to pay attention to where
those carbon buildups are right on the end there. Right here in this little portion.
Brush in there and let that sit. Now for your lower receiver. The lowers don't need to be
cleaned all that much because they don't get too dirty. I go ahead and I always wipe off the hammer.
Let the hammer go forward. Just inspect in there. If you see any kind of dirt and carbon buildup,
go ahead and wipe it down. I don't on this one. So go ahead and release it.
You do not have to always clean your buffer and buffer spring, but for this video I'm going to
go ahead and do it. Honestly I generally only do it when I do the white glove cleaning again,
which is about every thousand rounds for me. But just take your buffer out. Wipe the outside down.
Any kind of carbon that's out there. Wipe the outside of the spring. This is like an oily rag,
so some of the oil is going to get on there. There are guys that do lubricate their buffer
and spring. That's fine. If that's what you want to do, it's fine. But I think just the
bolt carrier riding back there deposits some lubrication and that's okay. So go ahead and
put it back in there. One thing I should have pointed out though, for those of you guys that
are new to the AR platform, the way you get that out is there's a little detent right here.
Just go ahead and push that down and that'll help it pop out. But that's it for your lower.
Your lower is clean now. Moving back to your upper guys. Everywhere that you just sprayed down
with that CLP and worked around with the toothbrush, all you're going to do is you're
going to wipe it up now. Go ahead and take a patch or a rag or whatever you're doing
and wipe that stuff off. One part you want to pay attention to is right there on the
face of your bolt there. Go ahead and work it around. Make sure you get all that CLP off there
and get all that carbon deposits out. You just do that until you're satisfied that it's clean.
In the area you want to focus on, a lot of guys will talk about the carbon buildup right here
on your bolt. They say you got to scrape it off and all that stuff. You can. Easiest way
I found to get it clean is scraping it off like I just said or they make this tool.
One day I may do a review on this tool just by itself but it's the Cat M4.
I wish I had that when I was in basic training let me tell you. This thing, I'm not going to
do a full review on it but this thing will help get your AR clean in a hurry. Set that off to the
side because not everybody has it so we're not going to use it for the review but or for the
demo here. Go ahead and wipe that off. As you can see there, give you an idea what it looks like.
That bolt is clean. I mean it's generally clean. No worries there. Go ahead and wipe down your
firing pin and again guys like I said when you're in basic training and you have to white love these
things all the time. My opinion and I worked in basic training as cadre for three years for what
it's worth. You don't need to do that. That's your firing pin. That is a clean firing pin for our
purposes here. Cam pin. Wipe that up. Retaining pin. Wipe that up. Set that off to the side.
Now we're going to work on our bolt carrier. All right we're going to go ahead and get the inside
there with one of the picks that we're using. Again if you guys don't have dental picks you
can use pretty much anything in there. Now you want to be real careful if you're using metal like
I am here that you don't scratch that chrome lining. So don't push hard on there. These are actually
clay picks for those of you guys that are wondering. It's a real real soft metal. It's not dental picks.
If you guys google clay working material these are soft like real real soft. So they're actually
probably softer than that chrome but it's what I recommend if you're going to use metal because it
is very soft and very unlikely to do any damage to your firearm using these versus some of the
dental picks that guys use out there. All right so you can look in there. I'm not sure how well
that comes off on camera but that is pretty clean. One of the things that makes it easier to clean up
is lubricating these rifles properly before you go out. If you lubricate these rifles and you
clean it within a day or two of getting back from the range and you don't let that carbon get hard
it will make a world of difference when you're cleaning these guns. Next thing you want to do
is clean right on top here just in that little groove because carbon does like to build up in
there. And I'm just going to wipe down everything off the outside of our bolt carrier here. Any kind
of all that CLP that's been working and breaking down that carbon from the beginning of the video
where we sprayed it around just wipe it all up. A couple different patches here do the outside
and a lot of guys will tell you you really don't even need to clean right down in here
but I do. And the way I do it is I just put a patch down in there work it around a few times
nothing too crazy and that's really it. I get it to the point that it comes out. You see how dirty
that was? Now I'm just going to do that a couple more times and that'll be the end of our bolt
carrier clean. So we're going to get into the star chamber now which is right in here. For those of
you who don't know this is a GI bore cleaning brush. If you do not have one of these they do help
a lot when you're doing those white glove cleanings. That said it's not what we're doing here today
but to use it you just insert it on your cleaning rod and spin it around. It does a real good job
cleaning out that the star chamber with these bristles here on the edges. One thing I found
is if you actually put it in a drill with the GI guide rod hit it real quick on low it'll make
it a lot easier for you but we're not using that again. What I'm going to do here is since I
already sprayed that CLP earlier in there we're going to go ahead and take our patch or whatever
it is that you're using and just work it around. And one thing you want to do here is if you open
your dust cover you can get almost that entire thing just from there. Work all the inside edges
of it. Work it around. Don't just work where you can see because where those lugs go in you know
that star chamber obviously is a rough spot to clean but if you have an angled thing like this
an angled cleaner like this it makes it a lot easier to do. But this one's actually not too
bad surprisingly. I think that CLP did get a lot of it down but we're just going to keep going
around in there until it comes out as clean as you'd like it to. I'm going to leave that decision
up to you guys but it's not uber uber important that you get it real clean each time because after
you fire 10 rounds it'll probably be dirtier than it was after your first run through.
All right guys I'm trying to get a good angle there. If you look in that chamber
you see that chrome lining all around it. Obviously this is presuming you have a chrome
line chamber but you can see all that chrome like that. In my opinion it's clean enough for a typical
range post range cleaning which is what we're doing here. Now that we have it at that level
what we're going to do is I close that dust cover up. I'm going to run one of these patches
just through the inside on both sides of the upper receiver. Just on the sides to get all
that carbon buildup that's stuck up on the side that runs next to the bolt carrier group in there.
What I'm going to do next is this side which is still clean. I'm going to use my angled cleaning
tool again and get all around where the gas tube comes back because that part is pretty nasty
generally speaking. Just work it in there keep wiping until it gets clean at least clean enough
to where you're comfortable with it put it that way. Believe me those of you guys that have had
to turn your weapons into weapons pools know you can spend a lot of time in that area because the
carbon will build up there quickly which makes sense because that's where it comes straight back
from the gas gas port. Just keep going until that's like I said as clean as you want it to be
as clean as you're comfortable with it. For your charging handle just go ahead and wipe the outside
of it down there shouldn't be too much carbon on it and make sure you pay attention to these little
raised areas here because that's where a lot of buildup is and just take your patch and just wipe
it on the inside there get all that carbon out that's it. The last part I clean guys is the barrel
first part and the last part so we went ahead at the beginning and put that CLP in there
and the whole time we've been doing this cleaning it's been working breaking down that carbon and
copper again CLP doesn't do the best job in terms of copper buildup but it does do some
that's why if you guys put a lot of rounds through your ARs every so often you want to
run some bore cleaner down there to get rid of that carbon fouling because it will affect your
accuracy eventually but at the end here we're going to go ahead and just keep running patches
through the barrel until they come out as clean as you want it. Now this one's actually not too bad
shockingly but keep running it through and up next will be lubrication guys.
Alright guys we're going to get into the lubrication here like I said this will probably
be the only controversial part of this video but I ran ARs for a long time I found this method
works pretty well so if you disagree with it awesome rock on but this is how I do it so we're
going to go ahead and just get your hand a little bit of CLP on there and work it around and we're
going to lubricate a light coat of CLP around the bolt obviously you want to make sure you get
down here as well around the part that I was talking about earlier where the carbon builds up
and I take a little bit of my CLP here and also a lot of you guys out there use motor oil and
that's fine no issues with that ARs I think it does work relatively well and go ahead and put
that just a little ring around on the inside of your bolt carrier I do that and I go ahead and
put it in and for those of you guys that are new to the AR platform I'll zoom in here for you
needs to be facing like this the extractor needs to be facing out because that's the way it's going
to come out of your dust cover take the cam pin and just put a drop of CLP on there I'm gonna put
that in again guys if you're using motor oil I have no issues with that I think it works very
well as long as you're using this synthetic motor oil all right put that in there I put no lubrication
on the firing pin some guys say light lubrication that's fine I put none on there because I think
if you do it's just more crap that can get gunked up one man's opinion put the retaining pin in
and make sure that we work it around there make sure it's working freely okay I worked like I
said in basic training for a while I also worked on M4 ranges and I can tell you the two biggest
reasons I saw AR platform rifles go down it's number one magazines number two the rifles were
too dry and under lubricated so just keep that in mind now I take a little bit of this grease again
any lithium-based grease is what I recommend obviously there's a million different types of
grease good website if you guys are looking for info on grease is Bob's Bob the oil guy but go
ahead and just take a look at this is what I'm using I've used it for a long time this stuff
and it works and I go ahead and the lubrication points here I'm going to zoom in here for you
is anywhere that you guys are starting this is a really new bolt so anywhere that you see
the wear starting so right up in here I'm going to put a little bit of grease
and then right here on the bottom rail as well and we're just going to push that
along the bottom okay you guys can see they're starting to be a little bit of wear there as well
so a little bit of grease up front not using a lot this is how I do it and it works well
we're also going to put some grease on the exact same spots on the opposite side there you go
as you guys can see I'm not using a ton of grease there are guys that really use a lot
more grease out there and that's fine you know if it works for them it works for them
but go ahead and get it right on those spots right there you can work around there with your
fingers if you want to make sure you distribute it evenly with that said all you're going to
need to do is cycle the gun a couple times and it will be distributed all right
and what I also do is I just take a little bit of CLP put it on my hand just put it around the
back end of the bolt carrier so that way there's a nice coat of CLP on there if you guys are using
oil just go ahead and put it on your same spots no issues there all right and now for your charging
handle there's three raised areas on this charging handle one right here and then two on each side
so go ahead and put a drop on there because those are the biggest friction points of your CLP
you're going to go ahead and put it back in your rifle for the bolt you got to shake it out make
sure the bolt's extended for when you guys are reassembling those get those you guys that are
new to the platform we're going to put it right there on your charging handle put it together
and that's your upper as I said there are guys out there that do lubricate
their buffer spring as well as their buffer I don't that's okay if you do have at it but I
think the bolt going bolt carry going back and forth will get some lube in there I go ahead
and reassemble the rifle upper and the lower just like we took it apart for those of you guys that
are new put the pins through what I'm going to do now is I'm just going to cycle the action a few
times make sure that lubrication is getting around put the weapon I keep the weapon on on a safe
try to pull the trigger nothing happens put the weapon on fire hold the trigger trigger breaks
cycle the action release the trigger it resets and you've done the cleaning and lubrication of
your AR as always guys if you have any questions comments concerns feel free to let me know
that's how I do it there are other methods they work as well but that's how I do it all right
thanks guys