Luaz from the Future. Suitability Test

Design & DIY
11 followers
74 Video Views·Mar 16, 2026
MyWarehouse is a cloud-based ERP system for small and medium businesses. Everything you need is in one system.
For those who aren't in the know, let me remind you that we're building a Loas from the future.
And in the end, we should end up with this ugly duckling.
A lot has been done over the last two years, and there's very little left.
We're about to send the car off for painting.
But before that, we need to cross off every item on the list,
which we've been working on throughout the previous series.
And in this series, we'll continue crossing it off item after item.
Another job that we'll have to come back to, but haven't particularly wanted to do,
is finishing up the ceiling of the floor.
When we were getting ready, we glued the front and middle panels in place,
and just screwed everything else on.
But dirt flies into the interior.
Everything flies into the interior.
In any case, this work needs to be done.
So now I'm disassembling the interior again, degreasing,
matting it, and finally gluing it on with sealant.
All the work is already finished.
There are some technical organizational issues down there, but all the work is finished.
So, you can safely glue the floor in place and, from there,
continue working on the fender liners and any other fittings inside the body.
In a previous episode, we showed how to sew up the floor.
This time, we decided not to roll out fiberglass sheets,
but to use a ready-made solution.
It's Textolite.
This laminated plastic is produced by hot-pressing layers of a fabric
base impregnated with thermosetting resins,
which gives it strength, wear resistance,
electrical insulation properties, and resistance to oils.
It's most often used to make gears, bushings,
gaskets, and components in mechanical engineering,
electrical engineering, and radio engineering.
It's not the cheapest option, but it's worth it.
In the end, we cut the necessary pieces,
glued them with sealant, and thoroughly sealed the joints.
Well, dear subscribers, it's time to sum up the year.
This year has been challenging, complex.
We hope the coming new year will be easier for us.
Here's what we'd like to wish you.
Happiness, of course, health, and may all your
subscriber letters planned here be answered.
Scared me, phew.
Well, let's read it in time.
Alexey Zap comments.
You need guy ropes or supports, so the wind can knock over a lot of weight.
A sail like that on the roof with a narrow wheelbase,
or park near a tree and tie yourself to it.
Quote.
There.
Probably commenting on the luau's.
Well, Alexey Zap, our luau's is for active recreation.
Active, enjoyable recreation.
We'll definitely check the weather forecast before leaving.
And if there's a hurricane or storm the next day,
we'll definitely not be going anywhere.
And the UAZ will remain safe and sound in our workshop,
and the wind won't tip it over.
And Alexey Zap, I wish you good health, good luck,
success in the new year, and may the wind be in your sails.
I think many of you know that we've decided to launch our product.
Not long ago, I talked about these construction kits.
They'll be appearing on marketplaces very soon.
But just a couple of months ago,
I thought it was impossible to understand all the nuances
and organize easy and fast production and distribution.
Fortunately, we were advised in time to find a reliable assistant, my warehouse.
The service allows you to track every stage of production.
You specify what your product is made of,
what materials and in what quantities you need,
and the system automatically calculates how much the finished product costs you,
including materials, labor, and other expenses.
This means that all stages are automated
and all employees see and know what's happening at what stage.
It's especially important for us that my warehouse
seamlessly integrates with marketplaces.
You can easily connect to the desired marketplace
and track everything through the service.
If you manufacture, sell, or are just planning to launch your own product,
production facility, or store, and want to do it without any hassle,
I can confidently recommend my warehouse.
Our viewers enjoy a free 30-day trial.
Link in the description.
A truly handy tool that saves time and nerves.
As you may recall, we have practically nothing left of the original LUAZ.
The key word is, pretty much.
And here's another part from the past that we've thoroughly restored and are using.
This is the panel that covers the gearbox.
It's installed directly in the cabin.
We laser-cleaned it and primed it.
The MAX 6074 reads.
As far as I can tell,
the rear-wheel steering can only steer like this up to 30 kilometers per hour,
as it creates oversteerability,
and the car will simply flip over at speeds above 30, 40 to 50 kilometers per hour.
The ASIC itself has a short wheelbase and high ground clearance,
making it prone to flipping.
In other words, it's a specialized vehicle,
not designed for high speeds, but rather for off-road use.
And in this case, the rear steering axle will greatly enhance
its maneuverability on this off-road terrain.
As you can see in our videos,
where you can easily spin around a pine tree and make a U-turn.
That's why we installed the rear steering axle,
not to mention doing 100 to 500 kilometers per hour on the highway.
And to you, MAX 6074,
in the new year we wish you success, happiness, and health.
And at the exhibition, when we assembled it and drove it,
it became clear that the difference,
the visual difference between the height of the windshield and these door openings,
was very noticeable.
So we decided to slightly modify the door opening,
specifically this opening for the glass.
Fortunately, when I was assembling the body structure,
I was counting on the top being removable.
I was hoping we could somehow arrange it and make it removable.
But we decided against it.
But I still have a second pipe installed here.
So, I'll just remove this pipe and visually align these parts.
And when we have it ready, I'll know this glass size,
and I can order the side glass here.
I found some guys who work with sliding windows.
We'll most likely order a ready-made solution from them,
good glass with a lock or not.
And then there's another redesign, refinement, or rethinking,
call it what you will.
Unfortunately, it's simply impossible to think everything through in advance.
Ideally, of course, we'd need a very meticulous 3D model to guide us,
but developing it would take more than a month, probably a year.
So we decided to use a combined approach.
We had a model, but it wasn't super precise,
and we knew a lot of questions would arise during the process.
So we were prepared for that.
And visually, when you walk away from the car,
it looks much more concise and appropriate with this edge all in one piece.
And now, when the windows arrive,
we'll install them and work on the windshield using these contours
to make sure it all looks harmonious together.
I actually thought that after I sawed off all the excess,
this pillar would look really thin.
But in reality, it looks quite appropriate.
Now I'll switch over to welding these extra holes,
clean everything up.
Yes, process it, refine it,
and then I'll move on to the other side and do the same.
And here we decided to install the simplest sliding windows,
since it's simply impossible to install traditional lifting mechanisms
in a door of this shape.
And looking ahead, I can say that this solution looks great in our design.
And now, a month and a half later, we have the long-awaited windows,
which we're trying on right away.
Our glass has arrived, and everything is fine.
But the team is divided.
Right now, the car, with its black frame and that crossbar,
looks like a cash-in-transit van.
We have a few options for solving this problem.
We could cut through the trim, the fiber itself, and recess it into it.
A window.
This will make the repair process much more difficult in the future,
if we break something.
But I think it will look good when all these seams are hidden,
and it will just be a window in the door.
It will look cool.
Or the second option, as a half-measure,
is to simply repaint the black frame to match the car.
Regarding this issue, we will probably ask you for advice,
because we still haven't come to a consensus.
Regarding this corner, the original plan was to install a mirror here,
but we decided not to go the traditional route with mirrors,
so the mirror will be moved down,
and we will tell you about it a little later.
So, the third letter.
Nechidor writes.
Still, a support will be needed for the retractable trunk,
since in the front part of it, in the remaining empty pocket,
a container with water for a shower will be placed.
You can take a shower right under the canopy.
The idea is not bad.
Perhaps we will improve all this.
Shower kitchens are, of course, cool.
I don't know, it hasn't come to this yet.
While we were making the tent,
we didn't think about all these, uh, human conveniences.
Maxim Moskalov C2C.
The retractable trunk can be used as a shower or toilet.
You can only hang it on the hinge or build the trunk into it.
In the car itself, you need to arrange a mini kitchen and a wardrobe.
The comments are all very similar,
and the answer to them will be the same.
We showed you how we installed our tent and retractable trunk on the UAZ,
demonstrated that it is quite possible to do.
It all looks convenient and comfortable.
And, of course, all these elements that you they've listed it.
So, a shower, a dressing room, a kitchen.
And what happens next, you'll see in the new episodes in the new year.
And to you, dear commentators and subscribers, I wish you happiness and health.
Initially, we planned to install the mirror in the corner of the door,
as is typical in all classic cars.
But our car is not quite ordinary, so we came up with this module.
This module contains a camera, which will act as a mirror in our car.
Accordingly, monitors will be installed in the cabin.
And this module also includes a turn signal repeater.
According to the render, we had a separate repeater and a separate mirror here.
We decided to play around with everything and combine everything into this module.
The guys printed it and have even connected it already.
It is, of course, unpainted.
This is a rough version, but now I need to place it.
It will be attached with four screws on the back of the body.
And here, too, it is very interesting to hear your opinion,
since we decided to install cameras instead of classic mirrors.
By the way, I modeled them Timur, the author of this project.
So all complaints are directed at him.
One of the last things to complete the interior layout,
specifically what will be inside,
so that everything is done according to the technical specifications
and we can start modeling the exterior, is the heater.
We decided not to invent anything at all.
We ordered a ready-made solution from marketplaces.
It looks, well, appropriate.
It has fans, an inlet and outlet.
Essentially, it just has a heater, radiator and a fan that blows air into four outlets.
Two will be for the windshield and two will go to the side window defrosters.
It even has a speed control.
It's not yet a primitive, high-quality thing.
All that remains is to install this thing in the interior and connect the hot water.
As for the rear lid, we still need to decide on the opening handle.
So far, we've been opening it all with a little finger twitching,
but it doesn't seem to work.
Based on the photos, I chose this handle.
Maximum minimalism.
It's electronic, with a limit switch.
That's exactly where we're headed.
We'll install an actuator, it will pull it.
But from the photos, I thought it was a little bigger here and the hand niche was a little bigger.
I wanted to install it like this and make it easy to open.
But it will be inconvenient to open like this.
It will be really inconvenient.
I made this thing, a frame for it, and a niche for the fingers will be made in the lower blitz.
And then it will all be easy to open.
This applies to the upper door.
After opening the upper door, we still have to add some stops and shock absorbers.
And then we will open the lower door.
With the lower door, I already changed the lock and made the lock.
The algorithm is that the upper lid opens first, and then the lower one.
Regarding the lower lid, it's handle and locks.
We installed the handle inside so as not to spoil the appearance on that side
and not to clutter anything.
I used the handle from the same car from which I used the lock mechanisms themselves.
The essence of the handle is that there is a rocker inside,
and with one press, it pulls both locks.
Everything, everything is completely mechanical.
Everything works perfectly.
It's even convenient.
Everything closes.
Alex1978 comments.
Yes, the design of the car, to put it mildly, is a children's cartoon.
Quote.
Dmitry Kuznetsov K-35.
This tent of yours is completely unnecessary.
By doing so, you've only disfigured an already terrible fake.
Irresistible writes that.
Only five cruisers have a more disgusting car appearance.
First of all, every opinion is very important to us.
We are pleased that you write and comment.
We believe that the purpose of this car is to evoke emotions,
and it leaves no one indifferent.
And this is not if the main thing.
Since we completely figured out the rear cover,
we decided to make a decorative protective cover for the rear as well.
It is very similar to the one we did at the front.
But here we approached the issue much more simply,
without scanning, modeling, and 3D printing,
since all three functions are in one master.
In the end, Sonya took the measurements,
rolled out a sheet of fiberglass,
cut everything to size, and glued the necessary part.
I propose and watch it.
In the end, it took a couple of days.
And here's the final fitting.
As you can see, everything is looking great.
And that means it's ready to be finished.
A little putty, sanding, and another day of fine-tuning.
As you understand, the drone read all your comments and,
frankly, was quite upset at times.
The thing is, there are a lot of comments
in which you doubt the reliability of such fiberglass parts.
In the end, Andriuka got pretty burned.
What would you like to say?
Have you noticed that we make everything from our beloved fiberglass?
If we weren't confident in this material, in our abilities,
and in our ability to make something like this,
we probably wouldn't be doing what we do.
Did you want a test?
Let's imagine that we're driving and hit a twig on our car.
It gets scratched.
And then we come across a boulder like this on the road.
Please don't write anything else about fiberglass.
Thank you.
We came across a boulder, strong, stronger than a broken piece.
And then we come across a loam.
As expected, a twig bent, a boulder split.
R U A Z.
Yeah, we got scratched.
You asked for a test yourself.
And now for the facts.
The protection was undamaged.
Yeah, we have some scratches.
The paintwork didn't seem to hold up.
What did you expect?
It's aluminum.
There are no dents, only the paintwork was damaged here.
Yeah, that's sad.
I hit the radiator grill, a corner chipped, and our gel came off.
So, this part isn't broken.
Just visually, the gel chipped because the impact hit the corner.
Visually, it's damaged.
Technically, it can't be broken.
What do we see on the hood?
Paint from a fire extinguisher remained on the LUAZ paintwork.
That means our paint is slightly stronger than the one that covered the fire extinguisher.
No dents, nothing, no cracks, nothing.
So, the hood is just regular fiberglass.
It withstood all these test loads.
Here's our new acquisition.
We bought them completely by chance, spontaneously, at a local flea market for a really sweet price.
I noticed them because even their factory shape is very similar to our shape from the render.
So, I think they'll need to be reupholstered anyway, with some minor modifications,
because the condition is what it is, whatever the price.
So, I think we'll remake them exactly to our needs and adjust them even more precisely,
closer to the render.
Well, as the original, it's quite appropriate.
Well, now we can only hope that the guys from the BGT auto restyling center in
Moscow will look at the remains of these seats with the same enthusiasm.
Surprisingly, no particular questions arose, and that was very pleasing.
It's immediately obvious that real professionals are at work.
They don't ask unnecessary questions, don't complain about the originals, but just they do.
And, as you can see, there were clearly reasons to complain.
Alexander, good afternoon.
Anyway, here's what I did with the backrest, I modified it.
I modified it here, modified it there.
Here's the restored part.
Basically, it looks pretty good compared to what it was.
Besides, they rarely get such examples, since they usually work on premium cars.
Although they can do anything and with anything.
Alexander, look, we basically chose this color.
Here, we sewed a cover out of genuine leather.
This is the color it will be.
The BGT auto restyling center offers all types of car work,
from simple oil and brake pad changes to comprehensive conversions into a mobile office.
You bring your car to one place, and everything you can think of for your car will be done in one
place, which is very convenient, since you don't have to search for specialists for different tasks
and there's always someone to ask.
Ultimately, in a couple of weeks, literally from the ashes, they reassembled these seats for us,
constantly sending reports and clarifying our color and design preferences.
We've worked with BGT before and highly recommend them.
The link is in the description.
Dr. Mozgov writes.
I hope you'll paint the inside of the trunk and install the lights.
Although you can hang a lamp, and it will be fine.
I agree.
Icon Motorsport writes 9146.
The inside of.
The trunk should also be painted, right?
And the backlight wouldn't hurt.
Yeah, Alexpo1FC comments.
Paint the inside of the trunk.
I'd like to remind our commenting guys that our LUAZ is still getting ready for painting.
That is, it has a test paint job.
We actually painted the trunk not with paint, but with a primer in the color of the UAZ,
to clearly show that it is conditionally ready and is more or less a similar color.
We have a big, grandiose job ahead of us on painting the LUAZ itself,
the trunk again inside on both sides.
We'll paint everything everywhere, make it beautiful.
You'll see about this in the new year, in our new series.
And to you, guys, success, happiness, health, and good luck.
We finished assembling the rear of the car, and we can go back to the front again.
Our seats have returned from being reupholstered, and now we need them put them in place.
Apparently, they're too low compared to our old seat,
which is what I designed all the ergonomics around.
We ordered special runners for them.
And now we'll probably have to make some kind of podiums that will raise them a little off the
floor. It's about 60 to 80 millimeters. I just looked at them, roughly estimated them,
and compared them with our old one. This is how the runners arrive.
I'll start by putting them in order, and then I'll have to finish them.
My idea is that I'll drill out all these extra fasteners,
so that all I have left is the base itself, the mechanism for moving the seat back and forth.
And then, based on that, we'll finish it and come up with a podium for them.
Here's the finished look of the nightstand. Everything is as primitive as possible.
Just a rectangle with holes, with threaded rivets.
I've already installed the seat on the nightstand, which I welded it for her,
and then one issue came up, but it was most likely due to my carelessness.
I didn't notice that the seat mounts themselves were at different levels.
Probably, when it was in the car, some mounts were higher and others were lower,
but I welded the nightstand to the same height, so, well, there's a pretty big angle,
and so I'll clearly have to redo everything now. How I'll level it now and how I'll raise it,
how much it needs to be raised, I'll measure. Well, carelessness leads to a ton of unnecessary
work. This is what the modified seat mount mechanism looks like. I changed the position
of one of the runners, lowered it so that the seat would stand level. I made this kind of
lowering to accommodate the strange mechanism connecting the runners. So now I need to repeat,
clone the same thing on the other side and install the seat in the car.
We often use threaded rivets everywhere in all our projects.
Let me show you how it's visually it works because I've been asked questions like that.
It's not very popular, and it's not a popular technology with everyone,
sometimes it's really a shame to just buy, like, a rivet gun.
We have these threaded rivets. They come in all diameters.
We drill a hole of the right diameter and, instead of welding a nut on the back,
we simply pull the rivet out with one quick movement. That's it.
It's reliable enough for many things, but for our purposes, it's often more than enough,
and it really saves time. The seats are in place in the car.
I marked the center of the car, measured the center of the steering wheel,
and positioned this seat exactly in the center of the steering wheel.
I can't do that with this seat. This lever gets in the way. So I moved it a little closer to the
door. I adjusted it so it moves forward as far as possible and rests back. Now all that's left
is to secure them in the car and figure out how to attach the seatbelt. I'll probably have to add
some more. Some kind of crossbars to secure the seatbelt. And it's comfortable to sit here.
There's enough room for everything, nothing touches anything.
While I was installing the seats, when I tried them on the car last time,
I roughly figured out where we'd install the seatbelts.
Uh, the belts themselves, we bought these very simple, regular 3-point inertia belts.
The lower mount will be here. It will be a thick metal plate, and it will hold the lower part of
the belt and the opposite part of the belt. And the upper mount will have to be welded on,
here's a crossbar to somehow reinforce it, and this is probably where the upper part
of the belt will be. I've already made the blanks. Well, and the lower plate. Everything
in the back is primed, because we won't be able to get there later. All that's left is to weld it
all in place, and everything around it will be welded. And here there will be 3 more electric
rivets. To summarize about the seats. Well, it's comfortable for me to sit. The range of adjustments
is, we have a huge one. I actually can't reach the pedals because I'm tall. Plus, there's the
classic backrest adjustment. We sleep and drive carefully. The steering wheel is also
adjustable for height and reach. So, I think almost everyone can find their own personal
preference here. Our seatbelts are also in good working order. Finally, you can buckle up in this
car. I think the most attentive people have noticed the changes. We've also added an elastic
band here, and not only the elastic band, we've replaced all the hinges and all the door mechanisms
once again. Let me show you. And not only do we have a new rubber seal all around. But the door
now closes perfectly and doesn't wobble. It only wobbles when the car moves. The door hinges were
replaced with regular classic car hinges, but to install them, I had to saw through the inside of
this pillar and move it inside to have some extra space. The doors go under the trim. And thus,
we achieved fully functional, adequate doors. Now it closes and opens without any play or wobble.
Everything is perfect, friends. A year is passing, and it's time to take stock.
But behind the scenes, there remain a lot of mistakes, ruined moments, parts that were
sometimes redone more than once, a bunch of materials ruined and thrown in the trash,
and a huge amount of wasted time. And may everything work out for us in the new year,
stay with us, there will be a bunch of new interesting projects,
and we will surprise and delight you with them. And good luck to everyone.
There were also a lot of comments about practicality and the overall concept.
And here, it's probably best to respond to them not with words, but with action.
And so, on such a beautiful moment, we end this video. Thank you to everyone who watched up to
this point. It will most likely be inserted at the very end of what will most likely be the
last video on the channel this year, guys. No last video on the channel. Next year we're
expecting a real blast. We'll finish what we started and not be afraid to start new things.
Well, you know, we're always much more inclined to start new things. So, see you on the channel,
we feel your support, we see all your negativity, we read everything,
we're familiar with everything. And good health to everyone in the new year.
