https://www.youtube.com/user/VideoJoeShows How to install a toilet tank to a toilet bowl...Part 1 is what this DIY howto video is about. VideoJoe has just changed a toilet tank spud nut & adjoining rubber gasket assembly & now he is ready to re-install the toilet tank to the toilet bowl. This is quite the project but once you do one toilet I know you can do more. Do you have to be a plumber? A no goes here. Just keep track of what you're doing & the sequence & the most important thing is to get the toilet tank situated on the doughnut gasket properly & please please don't over tighten the toilet tank nuts to the toilet tank bolts or you could crack the toilet tank when you go to tighten the toilet tank down. Installing a toilet tank to a toilet bowl is easy...when you know how. Watch & learn as VideoJoeShows you how to install a toilet tank to a toilet bowl...Part 1 https://www.youtube.com/user/VideoJoeShows
AI Generated·May contain errors
that was no easy task in itself just to put those down now i'm all out of breath trying to fish
those in there and screw them and stuff okay i've got that all set now all right now i guess i can go
take that over to the toilet
you know this is an old toilet when you see a plunger like this one i have never seen one this
small look at the end how small that is you've never seen one that small it almost looks like
the rest of it's been chopped off you know usually they're really super wide like about like that
man i guess i better move that get those things out of my way
remember to have all this clean and scraped if you see any remnants of of any uh salt deposits
or anything like that you got to get all that out of there our gasket is only as good as this is clean
do a good job then put the tank back up there you're moving around the tank just be careful that
it's dry on the sides last thing you want to do is slip and drop this because it might be kind of hard
to get another one the very same as your toilet like i said not all toilets are the same
okay okay for right now that's all we're gonna do see it's kind of sloppy in there
the caddywampus just make sure you have it balanced on there and then we're gonna reach down there
and uh and put the nuts class is now in session you gotta do gotta make sure that donut
that gasket under there is positioned properly if you have that off now see how this is
kind of wiggly wobbly you gotta make sure that's positioned right you may have to
tilt it forward put it back sideways whatever because the last thing you want to do if you're
not taking care you may tighten this one up and it might be off let's say like that
see how that's crooked you can tell that's crooked but let's say you tighten that nut up
all the way you think oh i'll just go over here to the left and i'll tighten this one down
as much as i tighten this one over here and you keep going and going and going and it's getting
tight but you think you've got to go even further because you're for sure certain it's got to be the
same this is sticking out uh five eighths of an inch below the end of the nut you know this side
needs to be done the same or something like that this is just an example now okay and you go and
you try to tighten this one further or something and you can't get it you tighten it down and it
cracks you could crack this tank because you started off with it crooked you know you've got
to get this positioned right look at it see if it's level and look and see how it's setting on
your little gasket here and then we're going to start tightening we're going to put the nuts and
washers on there and stuff then we're going to start tightening it up and i want to make sure
i get it even you know what i mean if this side is going up three eights i'll make this side three
eights make the back side three eights okay look at it position it do this one up a little bit more
the same amount all the way around so as i'm tightening it up i'm always getting this nice
and flat i can look at that see if it's level and uh check all that kind of stuff out because
what they tell you is do not over tighten these nuts if you over tighten them you could crack
this and this is where i get paranoid because i'm going to be careful with this the best of my
knowledge and once i get it snug and i get it all even all the way around then i'm going to leave
it fill it up with water check it out if it's dripping just barely then i might tighten a little
bit more a little bit and a little bit and a little bit you know what i mean because this is porcelain
last thing you do you tighten that up just a little bit too much
it's all over crack city now you remember that bushing that that was attached underneath here
and and it was kind of fat and i said we're gonna put the washer right up against there well it's
not that's the spacer in between here that allows for your for your other bushings so that's why
i'm really glad they gave us that rubber do you remember i hope you were you were following that
if you weren't you got to catch this okay sometimes they don't give you these rubber washers and when
i took it off when i took the toilet off i didn't have these rubber washers there weren't any there
all there was was a washer and a nut they had a washer and a nut up here you know and they tighten
it up and this was right up against the porcelain you've got to have this rubber washer and it's
about a sixteenth of an inch thick it's just all thick piece of rubber then you've got the washer
then the nut so you tighten that up you've got that gap that rubber is rubbing on your porcelain
you're less likely to crack it you're gonna make a nice snug fit you see what i mean you go up just
a hair tight at least this washer is not touching tight up against your your porcelain it's going
tight it might be digging into the rubber just a hair and the rubber's got just enough give on it
that may not crack your porcelain tank but don't let me fool you you could still crack that tank
so be careful so now i got the rubber and the metal washer i'm gonna push that in there i'm
just gonna finger tighten it you know just i'm just gonna get it up there fairly snug not all
the way snug just loose a little bit i've already kind of positioned this and that looks pretty good
about there right now i've got to do left the left side when you put this up make sure you don't
think yeah yeah yeah the washer and the metal washer and and you might forget about it and you
know you could put that up first then the rubber gasket and then the nut well that's wrong if you're
not paying attention you might do that okay i'm not saying you're silly or anything but if you're
just not paying attention that could happen i'm not left-handed so it takes me a while to
figure out which way to tighten that you know okay i'll just make that snug and i gotta reach around
the back side and on here they gave me four washers which was nice in case you lose one
you've got it you've got you've got one to finish your project so uh you know i only need one more
washer like that so so i'm gonna save one washer and i'll put that in my arsenal for next time
i haven't put you to sleep yet have i
sometimes people say i talk too much you know i figure the more i talk the more you learn
keep that in mind okay i've got the rubber washer first then the metal washer then the nut okay
okay now i can look at that and do it once over and see how that's positioned
see if my how my gasket's doing down there i want to try to get that gasket smashed down nice and
level and even to see if that was tilted could you see that maybe one side's not going to be
as tight as the other for fear that you might think oh that's too tight i can't i can't go
anymore else i'm gonna i'm gonna break the i'm gonna break the uh the tank but yet you still
get a leak over here that's because your rubber gasket may not be down there nice and snug
smashing straight down so that's why you got to do it even kind of take a look at it and um
then and only then will you start snugging it up okay that looks pretty good right there
i'm just gonna make it snug by hand first just with my fingers you know okay now get ready
to tighten this down and i'm just gonna use a little crescent wrench like that you don't need
anything more than that okay so i have these hand tight and the screws are up pretty high
i know i need to suck that down when i suck that down i'm gonna make that rubber tighter inside
here now if you have a different setup obviously they give you different rubber gaskets and
bushings for around the bolts but this is how this set came so i'm sure i'm fine okay now before i
tighten that up i'm just gonna take my tape measure measure from the bottom of the nut
to the bottom of the bolt i got three quarters on that one i got a long three quarters there
which means that's a 16th over three quarters and the back side is a long three quarters that
means a 16th over so i've got it pretty good right here in this right hand side i'm going to tighten
this up by hand a little bit more check that out i got a long three quarters that's 13 16th for
those of you out there that don't know what a long three quarters is that means it's a 16th over
three quarters three quarters is 12 16th your tape measure is measured in increments of a 16th
or 30 seconds if you want to go even further so you know i'll make a little video of that
one of these days on how to read a tape measure but you know i'm looking at that doesn't that
look nice and level too i don't have it tilted forward too much or backwards too far tilted to
the right too much tilted to the left too much looks pretty good okay so now i start tightening
this up i'm going to tighten up this side maybe an eighth of an inch and i'm going to go over here
and tighten that up an eighth of an inch tighten the back side up an eighth of an inch and kind of
start checking things out like that do you know what i mean so i'm going nice and even hey it's
going to take a few minutes for that but wouldn't you rather be safe than sorry