https://www.youtube.com/user/VideoJoeShows How to install a toilet tank spud nut rubber gasket assembly...Part 1 is what this DIY howto video is about. Has VideoJoe ever installed a new toilet spud nut & rubber gasket assembly before? No! That's why he wanted you to watch this howto video to watch & learn to see what he is doing right & also to see if he is doing anything wrong so you can learn & see if this is something you might want to undertake yourself. As he shows you, he is talking about it & that is helping him learn as he goes too. He thinks he has everything ready to be put back together & is now re-assembling the toilet tank parts & gasket assembly. The one thing I could see him needing is another set of hands. If he had a helper for this project I could see it being so much easier. Take note. Installing a toilet tank spud nut gasket assembly is easy...when you know how. Watch & learn as VideoJoeShows you how to install a toilet tank spud nut rubber gasket assembly...Part 1 https://www.youtube.com/user/VideoJoeShows
AI Generated·May contain errors
Just want to keep track of my parts, and it's pretty easy to do because you should know which ones are your old pieces, okay?
I've got that
rubber
Gasket here. I'm gonna have to put this on first
It fits on
kind of tight
That's how you want it. I'm just gonna fish
Fish that up there push it back and forth
That's my first step. Just push it all the way tight to there, okay?
Here's another tip for you incidentally if you were a hundred percent sure that was leaking around this rim
and you thought it wasn't leaking around here and
Maybe you went to the store, and they just sold you this you thought oh, that's all right this one wasn't leaking anyways
Well, here's something important to remember
These are rubber and when they get wet they get pliable
They get tight in there, and there's a certain indentation in there
And it's not a given that if I were to put that back on and tighten it up
It's not going to be in the exact same spot plus
These dry out and get hard and you're and you're likely
To get a leak if you if you don't replace this rubber
Once this rubber gets dry
Then you've got to replace that I've had that happen a couple times with different things not necessarily with this
But with a Sloan valve or something something different that we're not even working on here, so
You know just kind of keep in mind you take things out, and they dry up, and then you put them back up in the water
They might start
Leaking and I'm hoping that this flapper see this is dry now
I'm hoping this flapper is still
gonna stop all the water if it doesn't it may be because this got hard and dried in a
crinkly area or a fold or just a slight warp to it and
Once it gets wet and saturated with water. Maybe it doesn't get pliable in the exact
same
Configuration as before and I might have to replace this flapper. I'm hoping that doesn't happen
You know but if it does
I'm gonna. I'm gonna check it all out and be aware of that and I may have to replace this flapper to
Keep that in mind
When you're fixing your plumbing
items
now that's not all the case because
with this type of install
You see there the washer. There's no way the washer is going to be right up against the
Porcelain anyways because there's rubber right there
You know so then you'd have the washer there and the nut
Okay, but even on the directions that I've got I looked at the directions. They want me to put this
rubber washer there
Then the metal washer then the nut I'll have to look at those directions again
And see because I don't know if I'm really gonna do that. I may just
May just put it on there like that
but
in either any case look at your directions read your directions look at your existing toilet the way it comes apart and
Nine out of ten times you put it back together the same way and you'll be fine
Now of course if you ever get into an instance
Maybe you don't have this type
Maybe maybe it's something else and it's causing you to put a nut or a washer directly on
the porcelain
You know
You've got the these rubber washers put that down first like I was explaining before
Okay, way better
You see what I was talking about see that rib right there a little nib
right there
That's the old one now see the new one doesn't have that and
You know I did a test I put the bolt in there from the inside of the
Tank when I tighten that up you can imagine this coming out of the hole here
Okay
And if you tight and if I put the nut on there and tighten that up and push that really super tight
It bulges right there
Can you see that
See how it bulges and it kind of makes the washer or the gasket look
like this one
See how that's got that rib
You tighten this up
See how it makes that same thing there
And that's what I'm gonna do
Just gonna tighten it up
from the inside and
Wow, I
know these
New ones were longer
See there
that much longer
and
Maybe you can see it that way better
I'm gonna go ahead and use these and I think that this is gonna stick up just a hair higher than
Then what was in there before not by much though
I think it's actually gonna be about the same, but anytime you get a chance to use new things
You know that come with the package go ahead and do that
but like I say if one of the
Ones on the tank next to the door opening as I look in there if I have to I'll go ahead and put the shorter
one in there
Now these are brass and brass doesn't really rust like steel
Bolts and this is this green on there. It's just a coloration discoloration
That the water puts on brass but brass
Lasts quite a long time. It's not really doesn't really
rust
like steel
Okay, so I'll be fine if I end up having to reuse those
Now let's talk about this just a little bit more. Oh, yeah, there's more to say about it
You know that was the existing one
And I was fortunate enough to find one
That's gonna fit in there. All right. I had to go to three hardware stores to find that
Now this is what I wanted to talk about
Did I have to what I have to put it back together like that if I couldn't find that
You remember what I was saying if you've been watching my videos, and I hope you have
Because I got quite a few out there that will help you save money on all kinds of stuff
But I've
Said, you know, there's usually two ways to do something there
If you can't figure it out one way think of some other way and chances are you'll figure out how to do it a second way
What do I mean by that? Well here you go. Here's an example. Let's say we couldn't find this
You've gone all over the place and you're beside yourself. You don't want to have to special order this you got to get your job done
You need to start using your toilet. Maybe this is the only toilets you got
You know, what could you do?
Well, here's the option
Okay, here's your here's your piece that fits in them in the tank now
This one here that I got obviously it came with the whole set came with that came with my other
rubber bushing
This was my new rubber bushing that I put on here already it came with new bolts new washers
New bolts all that a new plastic nut here that I'm going to use
But let's say you couldn't find a whole thing what to do
Well, you can buy just this ring here separate you buy the same size as the one that I took off
You can put that on there if it's a little bit thicker. That's okay. You can put that one on there, too
Okay, you can buy that separately and
Where these holes are here
You can buy all that stuff separately. There's different
Thicknesses of washers and stuff and they'll sell that as a package
With the nut the washer the bolt all the all the things and maybe you only have two holes in your toilet
Maybe your holes right here and one right there. You don't have a three-hole pattern like this one here. Well, that's fine, too
They'll sell they'll sell that
To you as well. That's why you you wouldn't really need this section here. You could you could do this all separately
Now now see this outside rim here. You can imagine just cutting cutting this part off and
All there was was a donut. I call this kind of like a donut. It's not really a donut
It's just a big washer rubber gasket. Okay, they have those separate to you. I could have bought that and
I could have pushed this in
there and then and then
Put this gasket just the round one and tighten it up with the nut a new nut or the old nut that I pulled off
Okay, look just like that except without
these
Prongs on here and that would be cut off. Okay
Then you just do these separately. I went to the store and they had three
Bolts I could about three bolts with different rubber
Washers, they're a lot thicker because they're they're set up differently because obviously you're not going to have this end on here, right?
so
That was the second way how I could have done this
now
you have to think about that kind of stuff, but I kind of wanted to match this up as best I could and
Since I found this voila, you know, this came with all the parts and everything and it fits just perfect
So I'm going to use that. Okay, but that's what I say. There's always
generally at least two ways to do something and
There's your example for this toilet tank connection. I
Think we're ready to put this back together
Okay
Got it from scratch. I've taken this one
Okay, I can take this. I've already put this bushing on there
And I'm going to put this back in the tank now reach down in there
Put that like that
Incidentally, I have to have this twisted in the right configuration
And I'll go over that after a little while. Okay, but that's going to go in there like that. I
Gotta put that in now or I could have put this in first
You know that
Push this through there get my new nut on here
Okay
I'm not going to make that too tight just yet
Okay so far so good
Now before I tighten up that nut I got my trusty channel locks here
I'm going to try to tighten that with that
I went to the went to the hardware store and I was trying to find if they had a special
Wrench to fit it in there and to tighten that up a
Little bit different than channel locks because I remember how tight that was when I took it off
I had to cut this rim out of there and get right in there
Well, you just have to make this snug you don't have to make it so tight
that
You can't do it with the correct the channel locks and I'm going to be able to do with the channel locks
I might do it this way. I
Get a screwdriver or something pry it in there that way and twist it that way or
you know get it like this and
pull it whatever but
Before I do that, I have to make sure that is configured in the right way
the
The tree portion I call it that's on the inside of that
You know
so when you pull that apart you want to you want to see how that goes because sometimes they're facing up and down where the
Flap is straight here and the back of it is straight
Well in this in this particular case, it's at an angle a little bit because this one has three
Screws remember so I can't put it straight because this screw might be in the way
Okay, if there was just two
Screws to attach this I would be able to do it that way
But because this one's here because I took note of that you play this video back
You'll see that it's a different angle and I'll show you that here in a minute. Okay?
Sometimes it matters. Is there a right or wrong way?
Sometimes the answer is
Yes