Carvin RSP Cleaning

TheGospelGuitarist
1 follower
Mar 30, 2026
Watch as I go through the cleaning of this 1996 Carvin RSP Ver.001.
AI Generated·May contain errors
Hey Gospel Guitarist here and today I'm going to do a video on my cleaning of my
recent acquirement of the Carbon RSP bass preamp. So I'll be opening this puppy up
and we'll be taking a look around inside and as you can see I have my deoxit and my
power air there so I can blow out the residue and dust and let's check out the inside.
One of the things you want to do is make sure you find some kind of a little container for
your small screws and things that you might be disassembling so you don't lose any of the
screws. So I'm just using a little metal tin here. Okay got it open.
As you can see or maybe you can't see it's almost empty. It has one circuit board here with
a preamp tube on it and then all of the pots and everything are on the front side of this long
motherboard. So I have to figure out how I'm going to get in here to you know clean the pots and
things like that. But let's at least figure out what kind of tube we have. You can just pull the
tube straight out. There's one bigger space in a tube that you line up when you install your tubes.
So this one here the tube is actually very clean. It doesn't look dirty at all. Like I don't know
if this is a replacement. It's a Sovtek 12AX7LP and I have a tongue saw that I was going to try
out in it. And I also have a penta tube. I have a pair of penta tubes that came out of my Digitech
2101 and I put mullards out of this box in that. And then I have my tongue saws
here which are 12AX7s which sound really really good in guitar amps. And some people online
suggest these for bass preamps. So I'm going to want to try this out and see how it sounds.
But I'll try both of them out see how they both sound. I'll probably wind up with the tongue saw
in there. One of the things I want to do is spray and clean out the tube connection. So I'm getting
your trusty can of Deoxit. It has a dial on the top for low medium and high output of the spray
which I thought yeah that's you know that's so handy right. So all you do is just spray it in
there and I don't want to get it too soaking wet. And then you can just take your tube and run it
up and you know put it in and get it all wet. Wiggle it around a little bit not too radically.
Just wiggle it around so that that Deoxit can get in there and clean out all those connections inside.
And you don't want to get in a real hurry doing this because you don't want to bend pins and
damage the socket. So but basically that's all you need to do is now don't apply power
very soon after you do this and make sure to blow out any wet and and get everything dried off.
You know give it some time. This will probably sit here for most of the day before I power it up
again after I get done cleaning it. But I wasn't hearing that much when I was play testing it.
When I engaged the tube I'm used to the unit I used to have had a little more growl to it.
And I don't know if I just had a better tube in it. Back then they were using groove tubes a lot.
So it made this is probably a replacement tube. It's awfully shiny for kind of a dirtier unit.
It's not too bad in here actually. Not not a lot of dirt. There's a little dust but
it's really not horrid in any way. I'm not seeing any major rusting or
damage on the components at all. I'm just going to go and look over everything real well.
I'll probably disconnect anything with connectors on it. These ribbon cables will probably get
disconnected and sprayed. Because sometimes ribbon cables can be the source of noise
and just intermittent operation. So just minor maintenance stuff.
And just let that sit there a little bit.
So I think that's it for the tube. And then you know you can just take your air
make sure you get this thing blown out. That's it. It's all there is to your tube clean.
And then pick your new tube whatever you want it to be.
And stick it in there. In this case I will try the tongue solid. It's probably just going to
sit in here and stay in here. So the pencils are okay for a mild gain. But this is only a
two stage gain. You have one tube. So if I want it to get really going I want to get a hot tube
in here. It's the whole purpose of having a tube in your base ramp anyways to get the little fuzzies
going. So I figure I'll have an easier time with that with a high gain tube as the tongue solid.
This is a new old stock tongue solid reissued out of Russia. And they're really really good tubes.
So pulling these ribbon cables off. As you can see they just got the little connectors
similar to what you have on your computer.
Same deal just give them a little spray there. And then slide these on and off over and over again.
And try not to damage anything when you're doing it. So get it seated. And then
so some people you know kind of like how does that get dirty? And well you'd be amazed what can get
wherever air can get oxidation can get. So you know it seems like it's covered up. If air can
touch it oxidation can happen. So I'm just going through everything and just going to clean
everything. I don't you know this is one of the first times I've had to do this. I bought other
gear. But this one has a little bit tight controls. They're not as fluid as the new unit when I
remembered it you know. But some of them are loosening up already just so. This one might
have been sitting around for a while. They're actually feeling a little bit better today
after using it a bit last night. So they may be waking up on their own. But I still would like
to deox them. I'm obviously going to have to check out some things online as to how to get into these
little tiny square pots. They're not the big round pots like your guitar and that you'd find in your
in your you know guitar heads. These are just little tiny pots on the board. So I don't see
an opening right now as to getting some deoxide inside them. And they may be sealed so they may
be self-cleaning just where you keep using them and they clean themselves. So I don't know.
Is there such a thing? I don't know. I know they're sealed pots but I'm not an electronics
expert. And I'm trying desperately not to learn how to discharge capacitors through my hand this
time. I had that wonderful experience with a tube amp. Trust me you want to learn how to not do that.
Not a very comfortable feeling.
And I didn't do it just once. I did it twice because I couldn't believe it happened the
first time. So I touched it again. Yeah I'm brain dead. Did that really happen? Okay
yep it happened. Shouldn't touch that ever ever again and I haven't done it ever again.
So that's it for cleaning these contacts and now I'll do it up here and follow the other cables
around and do them too. Okay well I have disconnected the ribbon cables and it's
pretty close quarters in these areas but there's not a lot of the molex plugs I guess. They're
kind of a molex plug type of thing. I just spray it in work them on and off of the
connections a couple times. And I also kind of dampened the rag with some deoxit and
I just kind of matted down all of the contacts on the back you know of the motherboards. I mean
I don't know if that does any good. I just figure you know epoxidation can happen at solder joints.
Well why not just get them a little bit moist and you know it's not going to hurt anything.
And may or may not do anything but it's supposed to you know take care of your oxidizing. So
that's about as far as I'm going right now. I need to do research on if I can get deoxit in those and
then if the video continues I figured that out. Well actually there is an obvious thing to do
when you're cleaning your gear. I made a video on this also. I just happen to use this because
it's sitting here at the moment. Take a guitar plug get some deoxit on it and run it in and out
and turn it inside your jacks. And the reason you turn it is because when you insert it you're only
rubbing the surface metals like one at one point. But your equipment is used to just sitting here
like this. Your plug is sitting there and it can that part of the contact inside gets used a lot.
So you want to turn it to scrape off any oxidation on the inside without pulling it in and out.
And do all of your jacks that way. So if you're getting noise not that kind of noise
but sometimes it's usually a lot of people talk about the effects loop on your guitar amp just
if you don't use it it sits there and collects dust. And eventually that dust becomes a conductor
and starts causing problems. So any jacks whether you use them or not just go through all the jacks
on your gear and clean it up. Now this is I prefer to do this without a cord on one.
I just don't feel like going across room and getting just a plug.
They're easier to turn if there's no cable connected to it. So that's all I'm doing now
is just running through and as you can see I got a whole ton of them here to do.
And so get a good amount on here and run through all of this and make sure that all of this gets
cleaned up. And doing good so far I haven't felt any voltages. I have this bad track record about
that. It's like I don't watch where my fingers are going half the time and I pay a price for that. So
you know luckily this doesn't have any kind of high power output. It's just a preamp but if you're
doing this with a guitar a guitar head and you've got your head taken apart and you're looking at
there don't you got to be real careful. Those tubes those capacitors the big brown black things
that look like batteries trust me don't touch those okay. Or you'll learn a lesson I learned
very quick and very rudely. So anyway I'm going to continue doing this you don't need to watch.
Okay now that I've gotten through all the holes here you want to take your
compressed air and blow out the jacks. You just want to make sure you're not getting any puddles
sitting around inside there. And while I got the compressed air out even though it's pretty clean
in here actually I prefer to blow out any dust bunnies because they can cause problems if they're
back there. Since I don't own this I don't know where it's been and where it hasn't been.
Okay well I got access to the faders but I don't think I want to use... Now Deoxit makes a
one specifically for faders because if you use the wrong thing on your faders it can start
deteriorating the fader itself. So I will probably remove the lid at a later date when I get the
fader specific Deoxit and use that on the faders. They're nice and tight they're really
nice and tight fluid right now. They don't feel cheap at all like some of them do.
So that's basically just a quick video on some of the things that you want to do when you get
a piece of older gear about just going through the thing and making sure everything is connected.
Make sure that you don't see any breaks in any of the cables anywhere.
Above all before you put it back together make sure you put your tube back in.
Don't want to forget that and power it on. I keep kicking the thing there. So you want to go
through check the cables see if there's any breaks even on your ribbons make sure all the
wires are actually connected at the other end. Just look for any like burn circuitry
and anything that might look like a problem just just look use your eyes. I know a little bit about
what what to look for for burn spots but that's that's about it. I don't have a lot of electronics
knowledge but I do know if I see a big black spot right here that's not good and something
probably burned out on the board there. So just check your gear out and be careful when you're
doing it as to what you're touching and and usually red leads are hot so not hot when it's
not plugged in but they can things store stuff so just watch your fingers. If you found the video
helpful please subscribe if you did and any helpful comments that you can leave about
checking things like this out please please post any experiences you've had especially if you're
an electronics genius so need all the help we can get around here. So thanks for watching have a good day.
