Ghost MIDI Hexpander Install Part 6 "The Wiring"

TheGospelGuitarist
1 follower
Mar 29, 2026
In the last installment of this build series I show you all the wiring which needs to take place.
AI Generated·May contain errors
Hey Gospel Guitars here and as you can see started to take things apart so I
can rebuild it in the new with the new daughter board there. The first thing I
did was take all of the pickup each one of these pickups have an individual wire
and initially with the Acoustiphonic they plug into this summing
board and then the summing board plugs into the Acoustiphonic using only one
cable because it doesn't matter it's an acoustic as long as it's picking up each
string that's fine and now I don't need this anymore but when you're using MIDI
each string can you know could potentially be a different instrument or
different tunings and all kinds of things so that's what enables MIDI to do
those custom tunings and things at the flip of a switch because it treats each
individual pickup as its own pickup where with the summing board it just
gives you an acoustic sound so it doesn't matter but they need to be
separated here on the MIDI board so you gotta plug them straight into the MIDI
board. This is the extender which is actually used for if you're if the
hex bander has to be too far away from the cable length then you can plug your
pickups into this end of the extender it's just like an extension cable is
basically all it is and then just plug this end into the MIDI board there so
I've been looking and thinking and wondering if the piggybacked see this is
initially underneath there the Acoustiphonic is normally run
underneath a big pickup and I'm thinking that this thing gets too close to the
magnetic fields that may not be good because this has got circuit boards on
it or circuit boards it's got ICs on it right there I don't know how sensitive
this thing is to magnetic fields but I'm guessing it probably wouldn't be very
but if you get it too close I think it could be a problem when it doesn't say
anything in the manual about anything like that but the Acoustiphonic is
placed underneath it but it's also got like an inch and a half from the bottom
of the guitar to the bottom pick up it's still got pretty good distance but
with this mounted on top of it I don't think I'm going to get that kind of
distance so I'm thinking of moving the board but it is attached to the bottom
of the guitar so for now I'm just kind of hooking up the wires to the MIDI unit
so I can test the MIDI unit all by itself and make sure the MIDI unit works
because it'll work independently of the Acoustiphonic so I was going to hook it
up and make sure that it works and these are keyed to fit in one direction so
that you can't put them on backwards so this cable here is coming from the MIDI
jack and then these cables here are from pickups themselves which I should
probably I will put some zip ties around these just to keep it nice and neat
there and so now I have to route or maybe I'll just plug these in first
these three cables here are the volume control the program selector and the
guitar switch the quick switch right here so I should plug these in and then
the whole MIDI systems up up and ready to go so the writing on these is really
tiny and I have glasses and it gets really crazy I need to check the manual
make sure I get it hooked up get those puppies in there in the right spot
switch to s1 s2 and when you do this you want the black this is the ground
wire the colored wires should go to the right and the ground should go to the
left so that takes care of that one MIDI switch connects right above it
and this one is the volume so v1 or v0 v1 for this one everything about the
system is plug-and-play but it gets pretty tight there's one open plug
between the pickups and the series of switches and volume controls and then
one open one here not sure what it's for but it's there so basically that's it
the MIDI system is all ready to go it doesn't need a 9-volt battery it's fed
through the I think it's what whatever pin it is it supplies the power through
the 13 pin connector not sure what number that pin is at the moment so you
don't need a battery or anything to run the system so now it's all hooked up
like this I'll test it see if it works with my gr55 and if it all works then
I'll take these cables here off and run them inside the guitar inside the guitar
itself which you can take some effort because there is a whole lot of wiring
in here and so this this is the completed MIDI portion of the circuit
okay seemed to work couldn't test much but seemed like the wiring was intact
what you're looking at now is the coast acoustophonic this is the ghost acoustic
system and all of these wires here need to be moved to where the red and blue
wires are on this row here because that row is the same as a row on the
acoustophonic and then I can attach this to the acoustophonic right there but I
may have to move it and so I'm going to check and see how this works out okay
folks that's the whole MIDI unit all wired so this row here is the switches
and pickups for the MIDI section and then all of these wires down here come
from the acoustophonic controls for tone volume batteries power supply for the
which does need a power supply and then this will piggyback on the other
controller board so now I just need to see if I can flatten these wires enough
to where I can fit it all in there and it might might fit we'll see well there
it is to my amazement the daughterboard sits right on top and I still have
plenty of clearance here for the pickup which I just had over the top of it so
if I lean a little forward there maybe you can get a better look pretty crowded
there must be a hundred wires in there so now to put it back while I still got
a test I'm gonna test the magnetics and make sure the wires are all still good
and reassemble it but that concludes the video as far as getting the board
the MIDI board all plugged in and all the controls on the guitar plugged in to
the MIDI board and MIDI board actually wasn't too hard to install in spite of
all the wires being in the way just use a nice bright LED flashlight so you can
see in there and I don't really see a need to move the board because the wires
are going to give you about an inch between the magnet the pickup and in the
board so that should be sufficient separation I would think so now to
reassemble it string it up okay there she is all put back together and
something's amiss because all three systems are dead so I either have a bum
MIDI board sent to me or there is something killing the system inside and
like a grounding something grounded out something else somewhere these are all
plug-and-play systems so there's no soldering so it's not like I made a
soldering mistake or double-checked all the plugs everything's plugged in the
way it should be so there should be something coming out of this but there's
that is a doornail magnetics don't work batteries good piezoacoustic don't work
the MIDI I get signals on the gr55 but they're kind of weird and the switch
program up and down isn't working to change the program so something's amiss
someplace not sure where it all worked before so but that's it for this build
for a while I'm gonna walk away from it and come back to it later I hope you
found a series helpful and informative and learn something as I have so that's
the better end right hey thanks for watching have a good day and don't
forget to subscribe for other things coming up in the future
