Woodturning a Segmented Vase from Firewood

Carving Art Channel
11 followers
AI Generated·May contain errors
Comments are disabled for this video.
Hello everybody. This project I'm using another one of those logs that I
picked up from a firewood pile about 10 years ago.
Most of this video is at five times normal speed.
I made kind of a sloppy cut with that chainsaw. I think the blades
were a little dull, so I'm just flattening out the surface here.
On the last walnut bowl that I made, the one with the mystery metal,
I received a lot of comments regarding the amount of waste
that was occurring because I didn't core it out.
I guess people just didn't like the wasted walnut.
So that inspired me to try and be a little bit more thrifty with this next log.
I don't have coring tools, so I decided to
use my bandsaw to mill this log down into about one inch thick boards.
And it worked out well. I ripped them down to about one and a half inches wide,
which is about the width that I like to use when I'm making segmented
bowls and so on. Had a lot of ripping to do. Obviously I didn't want to show you the
whole process, but you get the idea here. Not a lot of waste. And some really nice product.
28 two foot long boards. And this chart really simplifies the process of planning.
Like if I want a ring that is
three inches, I'm sorry, six inches in diameter,
then I need to know how long each individual segment should be
to equal the proper circumference of that circle.
And it's just sitting there right in front of you when you do it this way.
Obviously there's computer programs for this, but this is pretty simple.
And here I'm just switching from a ripping blade to a cross cutting blade.
And this is my 16 segment sled, and I've got it pretty fine tuned, so there's hardly any
variance at all. The glue ups go nicely. I had 11 rings to make, but I'm not going to show
all of those in the video. That would get kind of boring, I think. So I'll just show
one complete ring with the glue up, and you'll get the idea.
So this is ring number one, which will sit on top of the solid base.
And that actually is ring number two. I'll show you ring number one again in a minute, but
doing the test fit on this, it was right on the money. Didn't have to adjust anything.
Like I said, that cross cut sled with the angles is pretty accurate.
So the glue up's done, I just used a band clamp to pull everything together. Then I'm
tapping everything down to make it as level as possible. And there's ring number one.
And for some reason I had some kind of variance there that caused the angles to be bad.
I suspect I didn't hold the board tight up against the guide boards as I slid it forward
to make the cut. But anyways, you just do half a circle at a time, or half a ring at a time,
and glue them together using a couple of dowels to separate them,
and correct the angle with a sander afterwards, and glue it back together. It'll be a little bit
oval, but not bad. And there's all seventeen, or I'm sorry, there's all eleven rings all glued up
sitting on top of the base. And here I'm just using the bullseye center finder
to find the proper place to mount the faceplate, so I can turn out the bottom of the base.
Mounting the faceplate onto the lathe, I realized that I hadn't made my,
hadn't made the wood round yet, so I took it over to the bandsaw, took care of that,
and then remounted it. Once I've got the basic shape done, I cut the mortise on the very bottom,
and that's for mounting the one-way chuck in expansion mode, so that I can flip this thing
around and start working on the top side. And what I have to do here is flatten that top out
so that it can receive the first ring. And I also bowl out the bottom a little bit.
And once I have it close to flat, I'll take a sandpaper board and flatten it out real nice.
I'll check that with the board itself, just to make sure it's perfectly flat so I can put on the
ring. And there's ring number one. I'll center that as best as possible,
and then use the tailstock of the lathe to apply pressure. Let that dry for a few hours,
and then I'm ready for the next steps. For this ring and each subsequent ring,
I've got to flatten out the surface to receive the next ring. I've got to work on the inside
of the vase, because as I add rings, I just won't have access to the lower rings. And also
work on the exterior some. Just get it to a basic roundness, and that's more for stability than
anything else at this point. And here's where I start working on the interior. I don't currently
have the tools in my inventory to hollow out a vessel as deep as this one's going to be.
So I'll just do it as I stack on layers, and it works out well. And here I'm just basically making
the shape a little bit more to where I want it, as well as making the wobble go away. Making it
round again for stability, because as I add on rings, I want this... I don't want any weight
fluctuation. I don't want any wobble whatsoever. I want it to be as stable as possible, because
I'm not using tailstock. Not until the very end. I didn't record any video of the constant
sharpening that I did of this gouge throughout the process of this build, but I kept it very
sharp, as you can tell by the shavings. Adding ring number three. And again, it's the same process
for each ring. I'm not going to go through each step by step. So I'll speed through the buildup
of the rings, showing some detail on occasion. I use a combination of push and pull cuts,
being very gentle as I go. Again, I don't want to cause a check by being clumsy and cause this
to fly off the lathe. And here I'm just showing the rings as they get stacked up. All the different
steps I talked about have been done. Interior's looking great. Nice and smooth. And that's ring
number nine that I'm working on right now. Now the vase starts to flare out at the top, so I'm
giving this a little bit more attention on the outside. But again, it's just a rough cut, or I
should say a rough shape. It's a nice smooth, sharp cut. And here I slow it down to real time.
This is how long it actually took. How slow and deliberate I was being. I just did not want to
check at this point. The gouge is super sharp. Those shavings are very, very fine. As thin as
threads, some of them. And finally, ring number 11. And that means this vase is extended 12 inches
out from the vase, which is why I'm so concerned about stability. I did double check that chuck to
make sure it was tight throughout the process. Every time I added a ring, I made sure that chuck
was tight. And once I had the interior looking good, I pulled up the tailstock and started on
the exterior. Now I could make some shavings with a lot more confidence that that vase wasn't going
fly off the chuck. It's very satisfying seeing those shavings come off like that. It's hard to
describe. There was actually very little sanding I had to do, but I started at 100 and worked up to
500 grit. And then I applied Danish oil according to the instructions on the can. Three coats.
Walnut sure is a pretty wood. I did coat the very bottom of the inside of the vase as well.
When I took it off the chuck, I poured some in and sloshed it around. Made sure it was completely
coated. And there's the finished product. It took about a week. A lot of glue drying time involved
in that week. From an old piece of firewood, to milled lumber, to what I think is a real pretty
vase. Thank you. I appreciate your time and watching this so much. Please subscribe. More to come. Semper Fi
