LIVE: NASA Holds Press Conference on Upcoming ISS Spacewalks

Live News Network
1.4K followers
2 Video Views·Mar 16, 2026
NASA holds a press conference at 2 p.m. ET on March 16 to discuss two upcoming spacewalks outside the International Space Station beginning March 18.
Welcome to NASA's Johnson Space Center in Houston, Texas.
I'm Sandra Jones, and we are here today to discuss an upcoming series of spacewalks outside
the International Space Station focused on solar array upgrades.
Here today to discuss the upcoming series of spacewalks, we have three briefers.
They are Bill Spetsch, the operations integration manager for the International Space Station
program, Diana Trujillo, flight director, as well as Ronak Daveh, also a flight director.
We're going to start with some opening remarks from each of our briefers before jumping into
questions both in the room and on the phone bridge, as well as using the hashtag AskNASA
on social media.
If you are on the phone bridge and you would like to submit your question, please press
star 1 to submit it.
And without further ado, I'll turn it over to Bill for his opening remarks.
All right.
Thank you, everyone, for joining us here today to discuss the next two spacewalks outside
the International Space Station.
These will be the first two spacewalks for Expedition 74, the first of 2026, and the
278th and 279th in support of space station assembly, maintenance, and upgrades.
Our first one, on Wednesday, March 18th, NASA astronauts Jessica Meir and Chris Williams
will exit the station's Quest airlock to prep the 2A power channel for future International
Space Station rollout solar arrays, or IROSAs.
Once installed, this array will provide additional power generation for the orbital complex.
Additionally, the duo will swab the outside of the space station to test for the presence
of microorganisms.
This will actually be Jessica's fourth spacewalk and the first spacewalk for Chris.
Our second EVA, that will be spacewalk 95, two NASA astronauts will prepare the 3B power
channel in much the same way we're doing for 2A for a future IROSA installation.
We'll provide more information on the date and time of that spacewalk a little bit closer
to the operation, and we'll also release the names of the spacewalkers once we get through
this next EVA.
Beyond the spacewalk, we've had a busy couple of months with a busy spring ahead.
Following Crew 11 return and Crew 12 launch and docking, we've had a series of cargo mission
operations.
On February 26th, SpaceX 33 undocked from the space station, returning critical science
and research back to Earth.
On March 6th, JAXA's HTVX-1 was released from the space station's Canadarm and will remain
in orbit for the next several months to conduct experiments before harmlessly burning up in
the Earth's atmosphere.
Just last week, on March 12th, an NG-23 spacecraft named the SS William McCool was unberthed
and released from the NATO port of Unity.
Of course, still going, early this morning, we had the undocking of Roscosmos Progress
92 Progress, that cargo spacecraft from the Poisk module.
This marks the third cargo spacecraft to depart the station in 10 days, which is pretty impressive.
Next week, we'll start working on filling those ports back up a little bit.
We have the launch of Progress 94, following the repair of the pad at Baikonur.
Progress 94 will dock two days later to the Poisk.
So that launches Sunday, March 22nd at 6.59 a.m. Central, and docking will occur Tuesday,
March 24th at 8.35 a.m. Central.
And then to round out the near-term operations, we have the launch of the NG-24 spacecraft
targeting April 8th and launching from Cape Canaveral Space Force Station in Florida.
So we stay very, very busy on Space Station as we continue to progress through this year
in this increment.
And with that, I thank you guys again for being here and your interest in what we're
doing.
And I'll hand it over to Diana to walk you through the first EVA.
Thank you, Bill.
Good afternoon.
My name is Diana Trujillo.
I am the lead flight director for EVA 94.
Today, I'm going to talk to you guys about what is it that we're going to cover during
that EVA.
What activities are we going to execute?
So let's go to the first slide, starting with the team.
Okay.
Our EVA crew will be Jessica Meir.
Just like Bill mentioned, she will be wearing the red stripe.
And then Chris Williams will be wearing no stripe.
He will be our second crew member.
Next slide, please.
Okay.
Like Bill just mentioned before, Jessica, this will be her fourth spacewalk, and this will
be Chris's first spacewalk.
Next slide, please.
All right.
And then helping them out, getting them on the suits, making sure that we're preparing
to get out the door.
And then the same way as they're come back in, getting them out of the suit and performing
additional activities before they go back to sleep.
They will be our two crew members, Jack Hathaway and then Sophie Adelante.
She will be...
Sophie, actually, will be also helping us out with some of the activities that we will
be doing with the robotic arm, which you will see in a minute with some of the videos.
Next slide, please.
Okay.
For the ground, we will have as our EVA officer will be Farouk Sabour.
And then our ground IV will be Tracy Dyson, also another astronaut.
Our CAPCOM, which will be communicating with the folks inside the space station as we're
doing the spacewalk, it will be Scott Segatti.
Next slide, please.
Okay.
So let's talk about what we're actually going to do when we go outside the door.
So as you can see from this image, really what we're trying to do here is go ahead and
install the mod kit on two different locations.
My colleague here, Ronak, will be covering the three Bravo location.
I'll be covering the two Alpha location today.
So once we go outside, the primary task really is to go ahead and install a holder, really,
which we're calling the mod kit.
It will be on the canister of the VGA, which is the gimbal on one of the solar arrays.
What that will do will be to hold an iROSA, which is the rollout solar array.
The rollout solar array, just like Bill mentioned before, it will be arriving to the station
at a later time.
Once that gets assembled and put on the station, it will look kind of like the two wings that
you see, the two butterfly wings that you see on the four Bravo side.
But this EVA will only focus on assembling the structure that will hold it.
Next slide, please.
Okay.
So for this EVA, what else are we going to do?
So like I just mentioned, we go to Alpha mod kit on that canister that you see facing down.
That's where we're going to do the structure.
It takes about in between four and four and a half hours to actually get it assembled
with the two crew members.
After we do that, we have additional activities on the same vicinity, on that same area.
So one of them will be a DDCU jumper, which is to give us redundancy on the power system
that will be Jessica going into the DDCU jumper.
You see an arrow or a line there facing really what he's doing is pointing to the face that's
inward the page, inside the page, where she will be going.
As she's doing that, Chris is going to do two additional activities.
Chris is going to go to the race ring on the solar array, so the rotatory aspect or the
mechanism for the solar array.
He's going to go in there, take a picture to see what the current state of that is.
Granted, the solar array itself is parked, so when Chris gets close to it, he's just
going to see one sliver of that location so that we can take a snapshot of the current
state.
After he finishes that, he will come back to where you see the two astronauts in this
animation.
In that area, there are several boxes that Chris is going to remove the torque, so he's
going to release the torque and then retorque it, but at a lower value.
The intent here is that it will allow us to, in the future, do robotic operations if we
wanted to move any of those boxes.
Right now, the torque that we currently have in is higher than what the capability of our
robotic arm, so we just want to reduce it.
After all of that is done, the crew will start packing up, and then we will head back to
the airlock area where we will be doing two additional activities.
One of those will be by Chris.
You could go to the prior slide.
One of those activities will be done by Chris.
He is looking at the microorganisms.
Thank you.
Chris will be doing the microorganisms, and Jessica, on the way back to the airlock, will
stop and take care of a cover to one of the cameras that is on the robotic arm.
You'll see it on the video, but when the robotic arm gets closer to it, it has a camera kind
of on the elbow area.
Jessica is going to put a cover to it.
It will be evident on the video when we go through it.
Next slide, please.
Okay.
Let's talk about what we're going to do on the 2Alpha mod kit when we get out there.
Currently, today, we have the triangle shape that you can see in this diagram, and then
one of the lower struts, one of the lower rods.
The ones that we're going to install is the red, blue, and green one.
That's the focus of this EVA.
The prior parts of that bot kit were installed on the prior EVA that we did back in a few
... I think it was last year, actually.
Next slide, please.
Okay.
Awesome.
What are we going to do with the microorganisms once we get to it?
Once Chris gets closer to the area of the microorganisms, we're going to take about
five samples.
Areas where we're going to take samples is one of them is on the glove, is one of those
areas.
The other area is really on the thermal cover, on the hatch area of the airlock, and then
the other side is right at the rim of the airlock itself.
Those are the key areas you're going to see Chris taking samples on.
The beautiful part about the microorganisms is that the location is right in the airlock,
really, so we're just going to come back home and then just do the swabs there.
Let's see.
With that, that is all the slides that I have for you today.
Let's go ahead and queue up the video so I can walk folks through it.
Okay.
Awesome.
Like I was mentioning before, once the hatch opens, we're going to have Jessica coming
out.
First, she gets the strut bag, which is an eight-foot-long bag, and then she gets the
cable bag.
Then Chris comes out.
After they're both outside, Jessica will be the first one that will start translation
to the P4 area where the mod kit is located.
You'll see it here on the animation.
She starts moving through the truss all the way.
There it goes.
Jessica, all the way down to the mod kit.
At the same time, Chris is going to do a quick stop, get a WIFX, which is an equipment that
will give him more distance once he gets into the foot restraint so he can reach to the mod
kit itself.
Here goes Chris.
Okay.
Great.
Once they get there, they're going to cinch down the bags, and then they begin the installation.
They start with the mid-strut, and then Jessica gets the other side, the left mid-strut and
the lower strut, hands it to Chris, who's already on the foot restraint.
Then Jessica goes around, and Chris will then be turned so that he can be facing on the
other side of the canister where he will start now working with Jessica to put the mid-struts
themselves.
Here's where they bolt the second mid-strut.
After that, the whole assembly of the mod kit is now completed with the cables that
will be required for later on.
As I was mentioning, after that's completed, Jessica is going to go down on one side of
the area where they were, put the DDCU jumpers, while Chris is moving now to the race ring,
as I mentioned before, to take a snapshot of the current state.
Here he goes.
He takes a few pictures for us to understand the state.
Then he comes back.
Once he comes back to the same location where we had cinched down the two bags, he will
begin now the torque reset like I mentioned before.
Open the cable bag, get the tool that he needs, and then he begins the torque resets for several
of the boxes that you see here.
Once that is completed, Chris is coming back to the airlock like I had mentioned before.
Here's where he starts doing the microorganisms.
You can see that he has the canisters on his side.
He brings in the tool, he does the swabbing, and then he puts it back into the tool.
At the moment he puts it on the tool, he locks in the sample, and so he goes for the next
sample.
There is five samples that we're going to do.
There's seven samples that we're going to go do.
The minimum number for our activity to go around is five samples.
In this specific view, you will see him going back inside the airlock to do two of the swabs
that he has on his SCU.
In the meantime, Jessica now has made it to a location on the truss where the robotic
arm gets closer to her.
She puts the cover on the camera itself for the robotic arm, and then the robotic arm
moves out of the way, and she makes it back to the airlock.
Here you see Jessica putting the cable back inside, and then back inside the airlock for
the end of our EVA.
That will conclude EVA 94.
Now let me go ahead and hand it over to Rana, who will cover EVA 95.
Thank you, Diana.
Good afternoon, everyone.
Thank you for being here.
Yeah, we'll get started.
Let's go ahead and pull up the graphics for EVA 95.
My name is Ronak Devae, and I'll be the lead flight director for that EVA.
So again, big picture, our job will be to go install the modification kit that the structure
required for the rollout solar arrays on the three Bravo power channel.
We do have some additional get-ahead tasks that are noted on the chart here.
We'll be doing some torque reset ourselves potentially, and then also preparing a pump
module to just get into a better config if we were to ever need it.
One thing to also note on here that we'll see in the video that's not explicitly listed
as a task is we're actually going to set up the worksite for the three Bravo power channel
for the actual install of the IRO.
So those are really long EVAs, so we're going to do some get-ahead to prepare the work area
for the next crew to come out to ensure that we're keeping time on that EVA.
So similarly, you'll see our worksites here mainly are going to be the three Bravo, the
far furthest most starboard side of the station.
We'll be going to the S6 truss segment and working on that beta gimbal assembly.
And then if we get to our get-aheads, we'll be closer inboard at the one alpha integrated
equipment assembly area where we would do our torque reset, and then similarly on a
support platform in that area to prepare a pump module.
Next chart.
So this is a better picture.
We're looking at port 6, but to give you, again, some more insight onto the equipment
and how it fits together.
So Diana had some great imagery of building up the modification kit, and this kind of
shows us how eventually we'll install the actual rollout solar array to that structure
where those cables will come into play for the installation EVAs when we get there.
Next chart, please.
So similarly, after the two alpha, that'll be seven of eight power channels done, so
we will be the last modification kit, at least on the main power channels that we're putting
together on three Bravo.
Next chart.
Okay.
Those were all the graphics we had, so we'll go ahead and go to the video and kind of do
a narration of our spacewalk, and I apologize for saying a lot of things Diana said again,
but some of the choreography is very similar.
So similarly for us, we'll have EV1 egress out of the airlock first.
They'll get handed out the strut bag, which is a fairly substantial bag.
It's about eight feet long, along with the cable bag.
Once EV2 egresses, they'll be handed the cable bag, and then EV1 will start heading out
towards the starboard six location.
This is pretty far, so they actually end up setting up safety tethers for both crew members
and what we call slingshot to get both the crew members as far outboard as we do.
Similarly, EV2 will be making a pit stop to pick up what we call a WIFX, a worksite interface
extension piece of hardware.
They'll then install that at our worksite, along with the APFR, the portable foot restraint,
to get into a position to be able to install the hardware.
In that time, EV1 will be putting together the upper triangle that you saw assembled on 2Alpha.
We will be actually building out at the worksite, so EV1 will go ahead and assemble that full
upper triangle at that integrated equipment assembly.
And once that assembly is complete, they'll hand that upper triangle up to EV2 to actually
snap into the canister of the BGA.
Once that upper triangle is assembled, we start into the struts, so we'll first fasten
down that upper triangle, and then we'll, similarly to 2Alpha, start building out the
right strut and the left strut, so that'll first get handed up to the APFR, the foot
restraint crew member, while the bottom spherical bolts are driven by EV1.
And those get torqued down, and then the EV1 crew member will swing around to the other
side to assemble the mid-strut, so that'll, again, be fastened to the side of the BGA,
and then the APFR crew member will fasten that to the center upper triangle platform.
Once those are complete, the free-floating EV1 crew member will go grab the second, in
this case the left strut, again, fly over to the other side of the BGA, and we'll get
those installed in a very similar fashion to the right strut.
And once those are torqued down, similarly we'll install the mid-strut on that side,
and fasten those both to the canister side and then the platform of the upper triangle.
Once that's complete, we go ahead and route some cables for the eventual install of the
roll-out solar array, and this is also where we tighten some bolts on the mid-struts, which
have collars on them, they're kind of extending telescoping rods, so those will get tightened
down, along with cinching all the MLI that the thermal insulation down will route those
cables.
I noted preparing the worksite for the IROSA, so one of the big tasks we have after the
full assembly is complete is actually relocating that equipment to different locations in the
area of 3B to ensure that those are in adequate positions to save time for the installation
EVA.
We'll then clean up our bags and start headed back to the airlock, with EV2 heading in first,
handing in the cable bag, followed by EV1.
So that's all I had for you.
Again, thank you guys so much for being here, and I look forward to your questions.
Great, and thank you to our briefers.
For those opening remarks, we will now start with some questions in the room and on the
phone bridge as well as social media.
Again, if you're on a phone bridge, you can press star 1 to submit your name into the
queue.
If you do find your question has already been asked, simply press star 2 to withdraw it,
and on social media, use the hashtag AskNASA to submit a question.
Looks like we do have a question here in the room.
Mark?
Thank you.
Mark Corot with Aviation Week and Space Technology.
My question is about the launch of the two IROSAs.
Do you have like an approximate timeframe for launching them to the space station?
Will both of them go on the same cargo mission, or will it take two?
Yeah, sure.
We're targeting later this year to get those flown.
It actually flies as kind of a set of two roll-out solar arrays on one pallet inside
a Dragon trunk.
So they stack one on top of each other, and they fly that way, so we'll have two of them
show up at once.
So we'll be able to do both the two Alpha and the three Bravo then once they arrive.
The spacewalks that would follow, will that possibly be done this year, or you'll just
have to see?
Could go into next year?
No, we'll do them when the arrays arrive.
So whenever the IROSAs arrive on orbit is when we will go do those EVAs.
We don't want to leave them sitting up there for a long period of time uninstalled and
rolled up.
So we try to minimize the time that we have on there.
Richard T with The Post newspaper.
Questions for you, Bill.
So a couple of real quick questions about the different EVAs.
One, capacity for the ISS as far as electrical capacity.
Obviously, the IROSAs are being installed, those that have been installed in the past
and the future to increase capacity.
What is that theoretical capacity if you have that number?
And also, the addition of these that are coming up, is that to handle future experiments that
are going to require that extra capacity?
That's a great question.
I don't have the exact numbers off the top of my head.
These are the IROSAs, as you can see, the size is much smaller, but they represent basically
the same amount of power output of what we have on our solar arrays, the larger ones,
because of the change in efficiency in cells over time.
We have to wire them in in a certain way.
So there's only so much power we can get out.
But it basically returns us to our original kind of power capability on a channel.
Now, that capacity is used in a lot of different ways.
So we can use it to maximize, so our architecture is channelized.
So we have eight power channels on board the space station, and each one feeds a certain
set of loads.
And so when one channel doesn't produce as much power, now I have to limit what I do
on that channel.
And so this will allow us to be more balanced in everything that we do.
It provides us advantages for just trying to get the most out of the station that we
want to between now and the end of life, as well as providing advantages to us for the
final disposal of ISS.
As we've talked about previously, as we get really low in the atmosphere, we have to park
our solar arrays, but we still have to power everything that we need for that final disposal.
And so having these solar arrays up there actually really helps balance that load out
as well for that.
So it's twofold.
We get the advantage today, and then we get the advantage eventually at the end of space
station.
Thank you.
We are going to jump over to the phone bridge.
We have a question from Will Robinson-Smith with Spaceflightnow.
Hi.
Thanks so much for taking the time to talk with us today.
A couple for Bill Fetch as well.
Jumping off of the power augmentation question that was just asked, with Congress intending
to extend station life out to 2032 at this point, obviously that legislation is still
working its way through the Hill, but would this additional two IROSAs be enough to extend
the station life to that extra two years, or do you imagine there may need to be additional
power augmentation later down the road?
And then secondly, as far as upcoming vehicles heading to the station, is NASA still protecting
for the possibility of Starliner 1, the cargo version, flying sometime in April, or has
that been adjusted?
Thanks.
So to your first one, one, it's not appropriate for us to comment on pending legislation.
So from that aspect, I'm going to stay away from that.
We know how to address power on the ISS regardless, and we manage within the capabilities that
we have.
We have a lot of opportunities to throttle that if we need to for whatever situation
we get into.
On the question on Starliner, as the Administrator said, we're still working through the corrective
actions that came out of our investigation team, and we're going to fly that flight when
we're ready to go fly it.
Thank you.
We do have another question on the phone bridge.
This is from Bill Harwood with CBS News.
Hey, Bill.
Just following up on Will Robin Smith's question, and I'm trying to think of a way to answer
this that you'll be comfortable answering.
Regardless of what happens in legislation or political down the road, regardless of that,
I remember talking to Mike Sephardini many years ago about certifying the station to
get it to 2030 and all the things that had to be done to verify the vehicle would be
good for that.
Will some sort of analysis be required if you get directions to extend the life of the
station?
Anything you can tell me about that?
Thanks.
Oh, yeah.
Now, we definitely have to do analytical work to go extend the station.
There are a lot of factors that play into that.
One of the major life contributors to the station is actually just the orbital cycling
of the thermal loads on the structure.
As you can imagine, as you work a metal back and forth in a structure, it fatigues over
time.
We've designed the station to handle all those thermal loads, but it does have a finite life
at some point in time.
Now, where does that end up being?
We actually have analysis that goes and looks at the extension.
Also, we're informed by analysis that we do of the events that we've seen so far.
We try to be conservative in all the things that we do in our look forward so that we're
not caught off guard by something.
Then when things go better or we use less load for events, we don't have the worst case
docking scenario or the worst case maneuver scenario, then we get to take advantage of
that.
We have two programs that run in parallel with that from an analysis standpoint.
Yes, it does take us analysis to go look beyond 2030, and we have the means to go do that.
Great.
We are getting a couple of questions on social media.
As a reminder, you can submit yours using the hashtag AskNASA.
This first one comes from Copasetic on Instagram who wants to know, how long does it take to
plan a spacewalk, and what factors do you consider during planning?
Yes, that sounds good.
All right.
I will take that question, and then I will also pass on to Ronak who can add to it.
How long does it take to plan a spacewalk?
I think that a few things that we take into consideration.
One of them is we go ahead and dry run the activity itself on the NBL, which is one of
our pools that we have nearby where we have the space station submerged as a mock-up itself.
We go through all the execution of all the steps of that activity to make sure that we
have not only done it effectively, but also efficiently given the fact that we're going
to have the crew members outside.
In addition to that, there's a lot of preparation that we take to make sure that the procedures
are correctly done.
Plan A, Plan B, the creep sheets, which is what we call it when we go into any of the
troubleshootings that we need to do, which ones are the areas that we might be concerned
of.
So we can also write plans for that and be ready for the nominal case and then also be
ready for the nominal cases as well.
Also, in addition to that, we talk to the crew leading into the EVA.
It's about two weeks or so that we start the preparation with them onboard.
The preparation on the ground starts earlier than that.
But onboard, we start the preparation of their suits, making sure everything is on as we
expect it.
We understand if there's anything that we need to work on the suit or adjust.
As you can imagine, as the humans rotate with the same suits, we need to adjust the suits
for the new humans that are getting in.
And then also do all the crew conferences to ensure that their questions and our questions
are all lined up so we can go out the door and do it in the time that we have allocated.
Bruno, what else would you like to add to it?
I think that's a great answer.
I think it's also worth just noting that every EVA is different.
There's some tasks that we know are going to exist sometime in the future, things like
the mod kits that we've done before.
We've done six and a half of them, and every single time we've had a fun and unique challenge
where we get into the crib sheet and start to do some troubleshooting and let the ops
team kind of earn their keep that day.
Then there's EVAs like we did a few years ago with AMS, which is very development heavy
that takes years of time to just develop what we're going to do, build new tools.
So the timelines of all of those are really flexible and are driven by what objectives
we're trying to accomplish outside.
Yeah, it's a great way to look at it because not all EVAs are created equal in terms of
what it takes to go plan one and what it takes to go execute one.
We've done a lot of work ahead of time on what we call the contingency EVAs that we
have planned for the big ones that we have to go do.
If we have a major failure outside of ISS and we have to get out the door quickly to
go fix that, we can get out the door very quickly to go resolve one of those.
But when you get into a new task, it just depends on how complicated it is.
It took us a long time to figure out how to go do these mod kits the first time through,
probably on the order of a year to a year and a half to go figure that out.
Because again, we were in the middle of the design work at the same time and the build
and everything that goes along with it.
Other tasks where it's an ORU, an orbital replacement unit that we know how to replace,
we built it to go do that, it can be a shorter planning time.
But we still have to go look at all the tasks within an EVA.
And it just takes some time to build that choreography, practice it, build the procedures,
make sure that we're all in a good spot for all of the different what-ifs that could
happen during a spacewalk.
The ops team does a great job of adapting to the program's priorities and fitting really
within the timeline that we give them based on the urgency of the task.
Thank you.
And as a reminder, if you are on the phone bridge and would like to submit a question,
please press star 1.
We do have another social media question from Al on Instagram who wants to know,
how have spacewalk operations changed throughout the years?
Yeah, that's an interesting one.
I'll start and we'll pass it down the horn.
I think one of the biggest things that has changed is actually how we prepare for spacewalks.
So one of the big things that we are looking to mitigate when we go outside for a spacewalk
is decompression sickness and the means in which we do to prepare the crew to not get
into those circumstances.
So over the years, we've gone through very many different permutations of appropriate
protocol or trying to eliminate bubbles of nitrogen in the blood to really preclude getting
into those conditions.
I think that's one of the places I'd say for sure that we've had learning and improvement
over time.
I think the tools and how we do spacewalks have really been changed and innovated by
the unique and new objectives that we've given outside.
There are some times where we've, like Bill mentioned, in some of these critical EVA situations
where we're opening up new toothbrushes and 4-gauge wire to clean out bolt stanchions
because it really was our only option to put all the tools on the table and create something
over the course of a weekend to get a major power bus back up.
So I think a lot of our change has been driven by innovation and need.
Yeah.
And I will add to that as well that some of the changes are also coming from the suits
themselves.
And what I mean with that is we've been using the suits, this specific generation of the
suits for a while.
And so what we need to do on the ground is be more agile at understanding what are the
different ways that the suit can have more information, more data, different ways that
they are behaving.
And so now is the adjustment of the creep sheets or the cuff check, meaning how do we
respond to a suit issue as new things are coming in?
I think that this is something that's expected.
It also affects the task, for example, right?
When we talked about contingency EVAs earlier today or earlier with Bill on the prior question
is the fact that the contingency EVA task are things that we need to think about as
the space station is aging.
So it's an interesting question because you think about, yes, the suits and the station
is something that we understand really well today.
But as it ages, then we need to be very agile on the operations team to be able to respond.
And then even as we are creating or dry running or doing this task as we're building on
the procedures is recognizing that things can change any moment in a way that we didn't
expect it and we need to respond.
In our EVA, for example, in my particular two alpha EVA, half of the market is already
assembled outside.
The other half is what we're going to go do, as I showed you guys earlier.
It's understood that when we go out there, the structure is already outside.
Half of it is not.
So will we experience challenges with the vault?
That's what we get ready for, right?
And so it's the same thing for any of the other tasks.
I think taking a broader look at what's changed over time.
So if you look back at station assembly over the course with the space shuttle program
and building up the station, what we used to do was we had a plan for a set of EVAs
that we were going to do on that mission.
That particular crew trained for exactly those tasks and they did them over and over again
in the pool.
Today, we don't have that luxury, right?
We have a lot of our training.
They do get the critical contingency EVAs that each crew gets a look at those.
But most of it is task-based.
And then we do a lot of onboard training for the crew for the specifics of what they're
going to go do outside.
There are cases where a crew can experience something in the NBL here.
There are a lot of cases where they don't.
And it's just a skill-based thing that we work with the crews on and really build them
up to do any of the tasks that we need to do outside.
And then we do the training on all of it.
So there's less of the practice this specific thing in the NBL over and over again and more
of I know how to do these things and it applies to all of these different possible options
outside of ISS.
And it does look like that is all the questions that have been submitted today.
So thank you to our briefers for taking time out of their very busy space station operations
schedule to participate today.
And thank you to everyone who tuned in.
We do hope that you will join us for coverage of the first spacewalk on Wednesday, which
will begin at 6.30 a.m. Eastern.
So that will do it for us today.
Thanks again so much for tuning in.
