10 Pottery Trimming Tips Every Potter Should Know Stop Ruining Your Pots.

History culture hero
16 followers
5 Video Views·Mar 14, 2026
Are you struggling with trimming your pieces? Well you are in luck because in this week's video
I'm going to be going over 10 tips and tricks about trimming that I wish I knew when I started.
So if that's something that you want to learn about stick around and find out what they are.
So we're going to get started and trim this piece and I'm going to go over 10 tips and tricks
that will help you trim your pieces and hopefully prevent mistakes and or issues that occur when
you are getting your piece to get finished because trimming can make or break a piece literally.
So the tip number one that I have is to make sure that your rim is completely level.
Now normally you want to make sure it's level and you cut it level when you are throwing it
but sometimes you forget or if you cut it and you think it's level but it's not when you come back
now's the time to get it level before you flip it upside down and center. So you can either cut the
rim now while it's still stuck to the bat if it doesn't release or after you cut it off and you
pop it off then you can cut it but because when I pick up my piece it's still stuck to the bat
now is a good time to cut the rim. So what I'm going to do is I'm going to go ahead and lock it
into the pegs and we're going to be cutting this rim using an exacto knife. So when you cut the rim
what I recommend doing is after you start spinning the wheel I do recommend you trim the
rim to make it into a point and the reason for that is when you have a point it's much easier
to cut it level because there's less clay for you to actually cut and there's only one high point
versus if it is not pointy and it's flat you may cut not completely level across. So what I like
doing is I bevel one side so I trim one side at an angle at a 45 degree and then I trim the opposite
side the inside at that same angle and I keep going back and forth until both sides are touching
each other in the middle to create a point and then once I have that point I get my exacto knife
and when I cut you can either push forward from six o'clock resting your hands on the splash
pan of your legs or you can try to cut across like you normally do when you are cutting your
piece when it's on the wheel. For this method if you have really steady hands I do recommend
holding it at six o'clock and then you're looking at the height so this part right here you don't
want to cut at the very top you want to go down about halfway down the bevel so I'm going halfway
down the bevel once it's touching the clay I then slowly inch it forward so I'm not lifting it I'm
not lowering it I'm just going straight so this does take a little practice and once you cut all
the way through I stop the wheel and I lift up and I can remove that unlevel part and then I feel
the rim if it feels pretty good so I'm going to go ahead and just round the rim a little bit with
some water use my fingers to smooth and now tip number two is to dry your piece and then to rewire
it off so you can get it off the board so if you touch your piece and you notice that the clay is
still too wet you want to use a heat gun or a torch in this case I have a heat gun to dry your piece
before you wire it off and try to pop it off now normally you want to let it air dry naturally but
sometimes you just don't have time or if it was wrapped up too good and you're there you can't
really just wait because it'll take hours so heat gun will work in that case but my piece is dry it
feels dry enough so I'm actually going to rewire it off because right now it's stuck now normally
when you throw on a plastic board the bottom doesn't dry out but everything else does so if
you were to try to just pick it up from the piece it's stuck you could try to pry it off but normally
that bends your clay because then like I said the bottom's wet so what I recommend is actually
rewiring your piece off so when you wire your piece off if you pull from away towards you you
then want to pick up the side that is closest to you because that is the point where the wire passes
the last if you go from towards you to away from you you want to pick it up from away from you
because that is the point where the wire touches last there so wherever the wire touches last that
is the part that is the least stuck and that's where you should lift from so if I pull towards me
I'm going to pull it right here where my thumbs are off so I pull towards me and then I pick it up
right there and it should release nicely now from here we're going to dry it so we're going to take
the board out and if you wanted to dry the top because the top might still be wet you grab your
heat gun or your torch in this case I have a heat gun this is from Amazon I'll put it on my Amazon
storefront this one I like because there is adjustable dial to change the heat to make it
hotter or lower and then there's two settings low and high to dry your piece and that changes the
amount of air that comes out not the heat so right now I have it set to around 400 degrees I'm going
to spin the wheel a little slowly turn it on low I'm going to keep it about six inches away from
the piece I'm just going to spin it and then let the heat kind of dry the top and the amount of
time you dry it just depends on how wet the clay is so it can take anywhere from 30 seconds to
two minutes anything beyond that you may just want to throw another piece another tip slash hack I
have is you don't really want to be there holding it so what you can do especially on the bottom
because my bottom is wet and I need to dry it you flip your piece upside down and then you get
some cardboard or some sort of material to wall this area off so I have both a cardboard box
and a sheet of cardboard so the sheet of cardboard I'm going to wrap around here
so that creates this little border here and I'm going to take this cardboard box and put it on
top to create a little roof and then I'm going to take my heat gun I'm going to set it up right in
front of the opening I'm going to put it on top of an object in this case it's on a container
ideally you probably want to put on a container that's metal so in case this gets hot this
doesn't melt and then you turn it on and then you turn on the wheel so that it spins slowly
and then you let this run and you check it every minute or so so depending on how wet it is this
is a good way to let your piece dry out that's hands-free walk away and take care of something
else in the time being so we're going to go ahead and let this dry a little bit because the bottom
is wet and then we'll come back when it's ready okay I think that's good let's check
yep that feels so much better so now we are ready to trim now that the piece is dry we're going to
go ahead and tap center and you don't really want to tap center if your piece is too wet because
what might happen is your piece if it's wet and you hit it you might dent it so make sure that
your piece is dry enough and we're going to go ahead and tap center this so that we can get this
trimmed tip number three I have is once you rip your wads and you get them ready to put and secure
tip number three is to not push the wads into the clay wall this is really important to remember
because oftentimes when students are beginning sometimes the clay is a little too soft
and when they start pushing the clay into the wall it bends and buckles the rim causing it
to deform so when you push and put these wads down gently push the side so it wraps around it
but you're not pushing it hard into the piece you then push it down into the wheel head and
the pressure from your finger pushes the clay gently into the piece to secure it so once again
you gently wrap and then you push down because it's really sad to see people's pieces get deformed
when they pop it off because they were just a little too aggressive when they added these clay
wads to their piece okay so that is to get it secure don't push your clay wads into the piece
because it will deform but an even better way to get it secure without using wads is my tip number
four and that is to use water tension on the rim to get your piece stuck so you don't even need
wads so let's get this removed and let's talk about the water tension technique so the water
tension technique you just take your piece you get a little bit of water and you put it on the rim
then you put water on the wheel head as well and you're going to take your piece and put it on top
and then you're going to move it around to start creating slip you're going to feel your piece
slide around so if i tap it you can see it slides quite easily but the moment you start building
more slip you'll feel that tension grow that slip gets thicker and then it's going to be harder and
harder for it to move so once you start feeling it getting a little more stuck you slow your
movements and then you manually find where it's off center you gently nudge it to center it's
going to be much harder to move so it may move more than what you want and then you just center
here and this is a very great technique to learn because once you do it my from my experience it
does save time and it reduces your chances of needing to use wads the only downside of using
this technique is if your piece is really wet and you try to use the water tension technique
your walls are going to really just buckle under the pressure that you move back and forth
so make sure that your clay is dry enough when you do this water tension technique
so i got it to where i want it i spin the wheel slowly i give it a light tap to make sure it's
extra stuck or i can just gently push down and then i do a light jiggle it feels really secure
so before i start trimming one thing that i like doing is i like trimming a little pilot hole here
a little indent and this will allow me to apply downwards pressure with my left hand
and then i can support my right with this part so that this piece won't fly off now before i
actually start removing everything another sub tip if you notice that your rim is already starting to
be off center use a tool like a needle or an exacto knife and then make a center line for yourself
so you know everything beyond this line is off center you know that once you trim to this edge
everything should be true and centered so tip five that i have is about the angle that you
should hold the trimming tool and the pressure so angle when you trim you should have your
trimming tool at a 45 degree angle this is the best in terms of the leverage you can apply pressure
and it allows this to get a nice sharp carve into it if you go too flat oftentimes it doesn't carve
a lot out and if you go too wide it can kind of skip and kind of gouge but if you have a nice 45
degree you can get a consistent ribbon now pressure you don't want to apply heavy pressure
right away because that will grip the clay and your hand will gouge and then kind of get moved
by the wheel so you want to apply light pressure at that 45 degree angle and you increase the
pressure until you start seeing a steady stream of ribbons come off or trimmings once you have
that steady stream keep the pressure the same because that is the the pressure that you need
to apply for your particular piece and it's dryness and so what i'm going to do i'm just
going to continue trimming like i normally would and then with my finger on here my left hand on
here i'm going to brace my piece and then i'm just going to start trimming away any clay i have on
the overhang and then this part you trim as much or as little away as possible and i want my foot
to get established so i'm trimming away the overhang and then i'm going to go ahead and then
turn my hand like it's a doorknob like i'm turning a doorknob to get vertical to establish my foot
and a little bump of clay developed there so i'm going to remove that and then there i have my foot
more or less established and then i can kind of feather this trimming down a little bit to round
it out in my previous trimming video i used a needle to mark foot lines you don't necessarily
need to do that but as you're learning it does help if you're just trimming just by eyeball and
you realize your foot is too wide for your liking what i like doing is i take my trimming tool i
then i slowly just start turning the tool vertical to then make a new foot edge i'm
going to switch to a new trimming tool switch to my bigger trimming tool and i'm going to
get this feathered out and remove all the excess trimmings that i don't need to see
okay my piece is probably the wettest i would like it because the trimmings are kind of sticking to
itself but sometimes as you trim you may encounter your piece that's more dry and the trimmings are
coming off as little flakes so if that happens those trimmings that come off as flakes can turn
into dust really easily and if you trim even drier dust is actually being created and it actually
wears out your trimming tools because it carves away it grinds away the metal so this next clip
will show you how to hydrate your piece with a little water so that you don't encounter
dust and you get back to creating beautiful long ribbons now as i go down you can see my
trimmings are coming off as more flakes and ribbons and that's because that's too dry so
what you can do is you can add a little bit of water on your sponge coat the area that's too
dry with water so you hydrate the outermost part of the clay go back and then start trimming that
same area and then you should notice the trimmings coming off as ribbons again now the only downside
about hydrating your clay as you trim is the ribbons the trimmings will most likely get stuck
to the wet surface so just require a little more cleanup all right getting back to this piece we're
almost ready to start the next tip but i'm going to go ahead and just feather this curve out i
wanted a little less bulby and more angled down so trim that down all right and then now i'm ready
to start trimming the inside so i like starting with a smaller tool and when you trim the bottom
i always like having my bottom slightly domed because that allows less pressure to be placed
on the bottom because if it's flat it has more tension across the span of your foot and that
can cause cracks to develop so if you slope it it looks a little more fine-tuned and elegant with
your piece and it helps relieve some pressure and when i slope it i like making the middle the top
of the slope and then it slopes downwards towards the edge of the foot and then the height of this
part is not here yet but hide this part should match the height over here so i always start in
the middle and now i hold it like a pencil starting start from the middle and i work my way outwards
and i slow down as i get towards my foot so i'm left-handed so i'm going to go ahead and use my
left hand and as i use my left hand i'm trimming towards 430 instead and as i'm setting the height
of my middle once i get the height of my middle i'm going to make everywhere i'm going to make
sure that everywhere around it matches that height and then i'm slowly going to slope it down
so tap for thickness that feels good for the thickness here now i'm going to slope
the other area so that's where a good wide trimming tool comes into play and then now
i'm just going to make sure everything matches the height and then i'm going to start sloping
the clay so then i'm turning it like that doorknob technique again but focusing the
pressure on the right side of the tool to then slope the bottom to make it match
now to get this down because this is too wide you can either start above where you want to trim and
trim straight down if you have a steady hand but sometimes that skips and you end up trimming into
the main part of your foot so a more secure way that i learned is trimming at midnight
and you gently just push the tool towards midnight and that tends to remove little increments and the
you skipping upwards as long as you're trimming slowly are a lot less so i'm gonna get my thickness
there now i can remove these bumps here and now my height here matches more or less the height here
so if i were to cut this ring off i have a nice gentle slope across the piece all right so tip
number eight is adding some flair or style to your foot now there's nothing wrong with having a
straight foot but sometimes when you glaze it you want to be able to hold your piece by the foot
and if you don't have a corner here that is grippy it might be a little more difficult to hold so
what i like doing is creating an undercut or a slight indent so undercut would just be taking
your trimming tool and then you're just trimming your foot and you're just angling it into the
middle of your piece to create a little flair so then i'm going to switch to my smaller tool
and kind of clean up the trimmings that got stuck to itself and this little undercut that i added
because it's more flared out it will be easier to grip with your fingers now if you want something
a little more stylish instead of doing an undercut you can do a curved foot i'm going to go ahead and
trim this angled part to make it more straight again and then instead of making it flared out
i'm going to make it curved so i take the curved part of my tool the round part i'm just going to
trim a little indent and this little indent will allow me to grip it a little more and it just
adds a little more of a stylish bottom now the downside of this little indent is if you go really
thin on this part it's more prone to chipping so what i like doing is i then kind of trim away that
point and make it a little rounder but not too round because i still want to be able to grip it
and so there we go i got my piece more or less fine-tuned and trimmed and ready to start the
next tip tip number nine and that is to burnish and to smooth the piece so that i can remove all
these trimmings and trimming marks so before i can burnish i got to remove all these old trimmings
so let's knock these off and collect them with the trimming tool sometimes i put my finger behind the
tool to collect them sometimes you can dip it in water and then use that to collect any trimmings
that may have gotten stuck whatever technique you use to collect your trimmings go ahead and take
care of all those little bits so to burnish and to smooth the piece you just take a wet sponge
you add a little bit of water where you want to focus your smoothing and you can smooth with a
rubber silicone rib or a wooden tool but i prefer my fingers because you can really feel the clay
and what i'm doing is i'm applying very light pressure and i'm pushing all of those trimming
marks all of those bumps those dents those little bits back into the clay and it smooths the surface
and then i'm going to move into the inside and then you're going to be careful with your pressure
sometimes if your bottom's a little on the thinner side if you put too much pressure you can concave
it and then you can see that this area where i smooth looks much more refined than this area
so now i'm going to move on to this spot and normally when you trim your piece on the drier
side the trim trim lines are a lot more noticeable so burnishing and smoothing is something that i
always recommend because i'm not the biggest fan of trim lines and then to smooth areas your fingers
are just too big to reach a little bit of a small brush with a little bit of water on top will help
smooth those little bits that your fingers are just a little too bulky and this i kind of treat
as like a trimming tool and then just smooth mostly hitting the corners to kind of even out everything
all right now we're going to get this popped off and we're going to do the last tip of the video
so if you use the water tension technique to get it stuck i like positioning the pegs on the left
and the right putting my hands around it making sure they're dry and gently start wiggling until
it releases now as you wiggle if your piece was really soft to begin with and you put it on it's
going to get pretty stuck so just keep wiggling let that tension slowly start to release and
eventually you should be able to pop this off okay it's not releasing because it's got really
stuck so i'm going to try the other side and repeat now if you keep doing it and doesn't
release you might have to wire it off so that is the downside of the water tension technique
sometimes it works too well there we go starting to budge and you can also try to turn the wheel
and let it release but what i actually just did i turned the wheel and it released i should have
just pulled because my rim if you can look for my overhead cam got deformed so a new tip that
wasn't planning to tell you guys is to re-center this if you have a 3d printer you can make one
of these centering cones and use that to then push down to re-center or i know a lot not everybody
have this or if you have a bowl that's already round you can use that as your rim cone or
centering circle whatever you want to call it and use that to push down and that will help re-center
so i just push this down into the piece and kind of rotate and you got to be careful because if
your foot is really soft and wet you may want to do this step a little later or you can kind of
rotate the wheel and push the clay so that every part of your bowl is touching your rim so now
back to circle and the last tip is tip number 10 to smooth the rim so if the rim got messed up
because it was stuck too much like mines did take a sponge add a little bit of water and then use
your fingers to then smooth this out to your liking and because bowls sometimes you put your
lips against it you don't really want corners so i'm getting rid of those corners and then
rounding everything else out and there we go we got my finished bowl had some hiccups along the
way and of course it gets stuck again but we have a nice bowl and just so that you guys understand
why it was so wet i actually threw this earlier today so that was about four hours ago and i just
let it sit in front of fans so you can definitely trim pieces you throw on the same day if you give
enough time to dry anyway so we have the finished bowl i hope those 10 tips or 10 plus a little
extra will help you on your next trimming adventure to make your pieces exactly how you want it with
less issues and less headaches so if you like these kind of videos don't forget to like and
subscribe so you can see the next week's video come out when it's released and at this time i
say mahalo to all of the mud club members and a shout out to the mud club plus plus plus members
we have pamela k jameson sister bragdon and jj kiss so if you want to join the description has
the info so take a look and hopefully i see all you folks as members in next week's video
so thank you for watching and i'll see you guys in the next one
