How I Stain and Finish Bows

Unraveling the Ancient Longbow
4 followers
2 Video Views·Mar 1, 2026
How to achieve a natural 2 tone camo effect on a self bow. This video covers how to shellac a bow, as well as staining with dyer's polypore and other natural materials. If you'd rather use a more available stain, my favorites are leather dye and aniline dye.
Featuring music by my awesome cousin, guitarist Marcos Topolanski Quintero. You can find more of his work on iTunes and Spotify.
Welcome back to the world of bow making. Today I'll be showing you everything you need to know
to stain and finish a bow like this. I'm starting with a bow made of hornbeam.
This bow is fully tillered and shot in for a few hundred shots. If we have to change the tiller
we'll ruin the finish, so make sure you're absolutely done with the bow before you get
started. I try to be tidy about tool marks but there were always a few that escaped my attention
Take care of these now with a scraper. Also make sure your edges are well rounded,
the tip grooves are smooth, and all the transitions are the way you want them.
Start sanding with 220 grit sandpaper. You can start with 120 but be careful not to remove too
much wood from the belly. If the bow is clean with few tool marks I skip the 120 grit and go straight
to 220. If you find a tool mark, instead of digging at it with the sandpaper, quickly take
care of it with a scraper and then go back to sand it. Also don't forget to sand the string grooves.
Every surface that the string touches should be smooth and well sanded. Remember that the string
loop moves as the bow is drawn, so make sure the entire travel path is well sanded too.
If you leave any roughness here you'll wear out the string very quickly and the bow will be noisy.
Once I've sanded the whole surface of the bow the next step is to wipe down the bow
with water or alcohol. This will lift up any wood fibers that are laying flat
and now when we send the bow again we'll be able to give it a closer shave.
When the alcohol dries we can move on to the next grit of sandpaper.
I'll be using 320 grit. Once again, sand the whole surface. When I'm going to be staining a bow
I don't like to sand finer than 320 grit. Above 400 grit or so, the wood will polish too well
and it becomes hard for stain to penetrate the surface. This results in a patchy, uneven stain
job. If this were an unstained bow, I'd keep raising the grit up to about 600 or even maybe
1000 grit, but since I'll be staining this one I'm going to stop here. Part 2. Foraging for stain.
I decided to go with natural stains on this bow. If you don't want to go that route,
my favorite stains are aniline dye and leather dye. The advantage of leather dye is that it has
a bit of finish mixed in, so it builds up on the surface. This is really nice for woods that are
difficult to stain, like maple. Hornbeam has the same issue as maple because they're both
diffuse porous woods. During the early fall, there's a lot to forage, including several dye sources.
First, I found some fruits for jam. These fox grapes are colorful, but they're not very color
fast. The wine color doesn't last very long. So I kept looking. I found a bounty of edible mushrooms.
Porcinis, hedgehogs, chicken, hen, and shrimp of the woods. These were delicious, but not what I was
after. Next, I found some wood that's rotten with a green staining fungus. I also found some artist
conchs. These will make great decorations for the shop. Part 3. Staining. Finally, I found a
dyer's polypore, also known as the maize gill fungus. It grows around conifers and is a well-known textile dye source.
The tops of these mushrooms have a velvety texture, which acts like a marker.
The first few coats will be fairly light, but the color begins to build up.
I could have stopped here. The bow is ready for finishing, but I decided to add a second
color to the back of the bow. This technique I'm going to show you works anytime the back of the
bow has a natural texture that you want to emphasize. Young trees tend to have a more
pronounced pattern than older ones. Hornbeam and hophornbeam in particular have very distinctive
muscular textures, which can make really nice camouflage patterns. Most species have a bit of
texture going on, especially when they're young. This example is hickory. The secret to this
technique is applying a resist to the back of the bow. That way the colors don't mix.
I use shellac, but you can also just use whatever finish you plan to use anyway.
Now, if you do want the colors to blend, just skip the resist step. Here's an example of a maple bow
stained with iron vinegar. On this one, I did not apply resist, so the colors in the back blend.
For this bow, I want two distinct colors, so I'll be wiping the back of the bow with finish
to seal in the color. I'm using shellac, but if you don't have that, just use whatever finish
you plan to use anyway. Once the back is sealed, then I start scraping, slowly scraping away the
stain from any high spots along the back of the bow. Let the scraper reveal the pattern on its
own. If you try to force the pattern too much, it can look like you drew it on and not convincingly
natural, so be careful around knots and extra high spots. Once we have a nice pattern established,
we can stain the back with a second color. I'll be using blue cornflowers. This is an anthocyanin
based pigment, so it's fugitive, meaning it will fade over time. Now, that said, it can still last
for many years, especially with a nice finish over the top. My approach to natural dyes is to color
the bow in a way that will still look okay in the event that the dye fades. Some of my naturally
dyed bows are still colorful after many years. A couple of others have mostly lost their color,
and despite that, they still look great. Part 4. Finish. Shellac is my preferred finish, by far,
but you can also use whatever your favorite is. Most wood finishes will be more than okay.
I also like using true oil gunstock finish, as well as natural drying oils,
like linseed, tung oil, etc. The shellac I'm using comes in de-waxed flakes.
I dissolve it in grain alcohol. Use the highest proof you can buy. I keep a more concentrated
batch and a more dilute batch, so that one can penetrate a bit deeper. I don't weigh out the
mixtures, I just dilute them until I like the consistency. I'm starting with thick shellac,
since it's easier to build up layers with the stronger cut. Shellac dries within minutes,
making it quick to build up multiple layers. The thick shellac is more likely to cause runs
when you put on too much, so after a few coats, switch to the thinner stuff.
The key here is not soaking up too much shellac. You should have to wipe it on,
the shellac shouldn't be leaking out of your sponge. You want to have to smear a very thin
layer at a time. The advantage of thin layers is that they also dry much faster, usually just a
couple minutes for shellac. More thin layers leads to a much nicer result than fewer thick layers.
I typically lay about five to ten coats of shellac, depending on how thick and glossy a finish you
want. After the last coat, I like to rub the finish with a little bit of paste wax, just to
give a tiny bit of extra water repellency. Part five, the handle. I'm going with a piece of deer
hide for the handle wrap. Since it's not tanned all the way through, this hide still has the
toughness and moldability of rawhide in the core, while having the softness of leather on the
outside. After cutting the handle wrap mid-oversize, I mold the leather around the handle. I use some
binder clips to help mark the correct size for the final cutting.
I then stain the leather with some remaining pieces of mushrooms left over from the bow.
Don't forget to stain the bare edges, or the undyed leather will really stand out.
Now usually I just use leather dye, I don't have anything against it.
From then on, all that's left is making a groove for the stitches, punching the holes,
and stitching up the handle wrap. I also made a little bit of arrow pass from the same leather.
So
this one draws over 45 pounds at 28 inches, and is 70 inches long, knock to knock. The
is american hornbeam, aka musclewood, ironwood, or blue beech. The limbs are concave, and use the
so-called hollow limb design. Instead of only bending lengthwise, the limbs also flatten
laterally as the bow is drawn. This gives a little bit of extra kick, kind of like a straw that's
folded over, popping itself back up. Overall this was one of the most challenging bows I've ever
made. The same design failed on a previous try, and for most of the build I thought this one
wouldn't work out either. After over a year of bickering, we made peace. That's all for today,
I'll see you all next time. Until then, may your arrows fly true.
