@VideoJoeKnows #deckdryrot #dryrot #dryrotdeck #deckdryrotremoval #removingdryrot #removingdeckdryrot #howtoremovedryrot #woodrot #deckwoodrot #woodrotdeck How did my deck get dry rot?/DIY for beginners is what this DIY howto video is about. VideoJoe is getting ready to pull off the deck underlayment membrane to get under the actual deck in order to start removing the dry rot on the deck. Here's the question...how did the deck get dry rot on it in the first place? At the first look it appears that the deck underlayment membrane was installed pretty good...to the naked eye. Upon further inspection, however, there are some definite places where the water entered to then go under the deck which then caused all of the dry rot. Watch & learn as VideoJoeShows you what VideoJoeKnows...how did my deck get dry rot/DIY for beginners. Nice! https://www.youtube.com/user/VideoJoeKnows
AI Generated·May contain errors
So it looks like my first order of business is to score it around the sides kind of like how I'm
doing score all the way around the sides and then I'll probably score it in strips you know about
yay wide and just put some more score marks in it so I can just peel it up peel it up peel it up
peel it up so I have to cut another strip here another strip here all the way over here is
damaged this this floor is damaged like that all the way up to here then after that everything's
fine that's what I'm like what happened here and I can see I can see how they overlapped it
this piece is overlapped well this top everything on this on this floor slopes downhill so see
this piece should have been put on first then this one here should have overlapped it
and I'm thinking that's that's what what's wrong but it has lots of tape and gooey stuff
underneath it all the way along there you can see but it had to have failed along there could
have the water when it rains could have went down this uh stucco on the column and then right in
here it could have it could have went right down right down in there see right there that's where
water wet and then this osb plywood acts as a sponge just like a sponge when it gets wet
it just continues and grows and grows and grows it could it could have just been right there
and see over here I look this called it looks like it's sealed pretty much but it could have
went underneath that see right here look at that see that so as the water came down this
the stucco here it went right down on the on the inside of that that's a bad bad thing right there
look at that see and it leaked right along right along there went on this stucco rains
water comes down here they've got a piece of wood or something here I don't know why they
why they've got that this right here it went right down underneath that let's see there's the culprit
boom boom it waterlogged it dry rotted the two by six in here and the two by six is going over
there was hung off of here with and all that dry rotted and that pushed down and this next one
pushed down and the water just continued it could have been sealed everywhere else
but once it gets wet here then the next time maybe the first time it rained it got wet to there
second time it rained it moved out a little bit you have a downpour for a week or so this just
gradually grows and grows and grows and grows we're talking 17 years that it took to get this
look at the back side of this this plywood look at that looks like a mushroom you there
that's growing on the back side of that because that that plywood just when it osb plywood it's
just like it's like sawdust and little shavings of wood all glued together see all the little pieces
that's how they make osb plywood they use that for roofs and shear walls and all kinds of stuff
they even use it for this floor didn't they and hopefully i'll be able to tell once i get it back
all the way on how thick it is because i can't just measure a piece that i pull out because
when it gets wet it expands i might think it's three quarter inch and i might measure it might
be seven eighths in fact it might when it when the plywood is actually a short three quarters of
an inch let's say or maybe it's five eighths who knows we'll see when we get down to it well enough
of that we'll just i'll just keep going here but you see the flashing here's the flashing on the
outside see how the flashing is installed on top of this flooring well it should have been underneath
the flooring and this flooring should have been on top of that i believe and it looks like i'm
gonna have to look at that oh okay i was gonna say that should have some weep holes and it does
look see that hole right there you move along there's there's a few other ones see them down
in there that's what makes it so when the water when the water slopes off of this and hits that
then it's supposed to go out of those holes and i might drill those holes just a little bit bigger
too because you know what i'll bet you some of those holes got filled up you saw all the sand
and grout and and dirt and stuff i swept out along that edge see like right in there i i
all that was along that edge which tells me that that could have held up the water
from not being able to get out of those weep holes wow
yeah i didn't get very good sleep last night because i was thinking about this project how
am i going to take the plywood out from underneath the flashing without disturbing the flashing if i
can't get the flashing out what about this what about that and i kept thinking about all these
things until finally i thought hey let me go back to sleep and i'll figure it out as i go
you know but one one last thing before i start cutting see that flashing edge along there see
the paper and the membrane should have been on top of that so when the water when the water comes down
and this whole thing is sloped mind you okay when it gets down to there this paper or this membrane
should have been on top of that flashing so that the water didn't want to have a sense to go
underneath that but they didn't they just put it on top and they probably put some mastic or
something down there and they thought okay hey let's just squash it in there it'll be good enough
let's see this one here they didn't necessarily have to put the membrane on top of that
this piece here is still sloping at an angle going down and the theory would be
that it would only go out at the bottom corner so i may have to drill some holes in that flashing
later and you know theory has it that point should be level with that point there if everything's
going downhill at the right angle so any water that puddled up there should go flat and then go
out through this one same with this edge here this is still going at an angle so most of this water
that hits on there should flow out that way but there's holes along there so i'll drill those
holes out too so if any water does happen to get in there it can flow out of those holes
through the flashing and that flashing goes out on top of the stucco on the outside see
and i'll have to i'll have to check all that stuff out make sure it's all able for the water to go
through there see i just stepped right there did you hear that see if this membrane wasn't there
i could have stepped my foot right through it so once i get going after i score all this then
i'll start at one end and start working backwards or something we'll see slowly but surely we'll
get this thing done all right just going to show you a little bit more of my scoring looks like
so i know i have to score at least there
okay now i gotta think light like a munchkin or something okay i'll just keep it rolling here
i'm going to try to work over there at first and peel it back a little bit
see what happens that's where it's all failed so i gotta be careful gots to be careful