4TB Seagate Hard drive not spinning no power motherboard Repair

Tech Care
3 followers
Feb 25, 2026
Last repair for the day. I do not have any videos recorded for the day so I thought let me
work on this one. It's actually 640 right now and we closed at 6. We're going to be working on a
Seagate hard drive, a four terabyte Seagate hard drive that came in for data recovery.
Customer said the drive does not power on, it does not spin, nothing. Drive is completely dead.
From experience I know anytime we have a problem with a hard drive where the hard drive does not
spin or power up it's most likely a problem with the motherboard. Right now we have four
screws on the board. I already removed the screws and we're going to separate the motherboard and
let's take a look under the microscope and see what's going on. Why is the drive not powering on?
The customer does not care about the drive but he cares about his data. He can always buy another
hard drive but he cannot buy data. Quick visual inspection just to see if there's anything obvious.
Maybe this board was worked on before or maybe a component is blown or a component is discolored
or a component is ripped off the board. The board is not that big, small, so it's very easy and quick
to do visual inspection. That's it, done. And as you can see everything looks perfect. So what's
the problem? Why is the drive not powering on? Two possibilities. Number one, the internals of the
hard drive may be bad, which is very unlikely. And number two, and option two is the motherboard is
bad. Most likely it's a motherboard issue. What I want to do based on my experience working on hard
drives is we're going to start by measuring those zero ohm resistors in beep mode, meter in continuity
mode. And let's see, are those resistors good? They are. This one is good and this one is good.
What about this diode? Diode we need to measure it in diode mode. Red probe on top, black probe on
the bottom. We do not have a short so the diode is good. And let's measure this one. Red probe here,
black probe here. And look at that, we have a short, short circuit. What if we flip the probes?
Flip the probes and we have a short circuit. Most likely the diode is dead. What else?
Any more zero ohm resistors? We do have two more right here. Let's measure and make sure those
resistors are good. And look at that, the resistor is blown. Zero ohm resistor is more like a fuse.
It connects two traces together and you can think of it more like a fuse. So it's blown.
And this one is blown too. So we have three bad components on the board so far. One, two,
and three. Meter in diode mode. Let's go over this one. And this one is good.
And honestly right now I do not think we should spend any more time looking around because
we may have already found our fault. We're going to get rid of this guy here. We're not going to
replace it. We do not have to. To get data we can remove it. It's used for protection.
And we're going to replace the two zero ohm resistors that measured open. Maybe I can go
home early even though I'm already late. So just mark a line right here. And that's just a quick
indication of where that line is on the diode. Get rid of this diode out. And let's replace those
zero ohm resistors. Bye bye. And bye bye. Just a little bit of flux. And since I already have
my hot tweezers, why not use them instead of a soldering iron? Great. Get rid of the glare.
And those resistors I believe they are size 603. And what do you get a size 603 zero ohm resistor
from the resistor books that we carry and sell on our e-commerce shop. And look at my label. I
have the book labeled. But over time the label goes bad. And we have to create another label
and put it on the outside so we know. Let's put it on the side. And I have the zero ohm strip
right here. Let's go back under the microscope. Solder those in. And then we're going to try the
drive to see if it works. Apply flux. And let's grab our zero ohm resistor from here. We need two.
Now it's going to be hard to grab that component. So what I do is I wet my tweezers.
If we have enough flux on the board. Right here. And just grab. See? Magic. It's like a magnet.
So we're going to grab the component. Make sure it's aligned. It doesn't have to be aligned
actually. And heat it up from here. Done. And now we're going to do the same thing here.
Done. Now we're going to do the other end. Done. And finally. Done. How come this is
bridging with this? It's the same line. Doesn't matter. When the mask is exposed in the middle,
then solder will flow that way. We're all good. Clean up. All right. And let's see.
I connected the board with two screws onto the hard drive. And plug it in. Yes. Yes. The hard
drive is spinning. We hear the tone. And I want to see something on the screen. So far nothing.
But the computer is thinking. So that's a good thing. The red ones are my hard drives.
And both of them are full. And right now I'm not seeing this hard drive on the screen.
Let's wait a bit more. I mean the hard drive is spinning. It's a four terabyte hard drive,
so it may take a few seconds. Unless of course it's an Apple hard drive and it's not formatted
to show up on a PC. In which case we're going to have to try it on a Mac. It should have showed
up by now. The hard drive is still spinning. Okay. Let me shut it off and back on. You see
when I shut the drive off, we heard the tone. And now back on. Nothing. Great. What is going on?
Okay. Maybe I'll try this on a Mac and see what happens. Let's try it on a Mac. I have the hard
drive connected to this adapter onto the computer. And we're going to turn it on.
The hard drive is spinning and we should see something right on the top here.
Look at me. Who needs a camera when you can see me on the screen? But do not focus here.
We need to focus here. If something will pop up right there. Yes. Yes. Yes. We do see
the drive right here. Double click on it. And I'm going to have to blur the screen later on.
Click on it and we can see all the files. Awesome. Awesome. Let me go back to my camera
right here. I hope you enjoyed the video. Don't forget to like and subscribe.
Leave a comment if you have any questions and we'll do something else in the next video.
