Man Can't Adjust Concealed Cabinet Door Hinges Then Does It Anyway

VideoJoeKnows
63 followers
8 Video Views·Feb 15, 2026
@VideoJoeKnows
Man can't adjust concealed cabinet door hinges then does it anyway is what this DIY howto video is about. VideoJoe is working on adjusting & installing some concealed cabinet door hinges in a little condo & now he's ready to adjust another cabinet door hat he just installed new concealed cabinet door hinges, the soft close concealed hinges, that are now making the cabinet door rub on the side of the microwave prevent the cabinet door to close all the way....What?!! Watch & learn as VideoJoeShows you what VideoJoeKnows...man can't install & adjust concealed cabinet door hinges then does it anyway. Nice!
https://www.youtube.com/user/VideoJoeKnows
Now here's something you may run across
Now the other hinges work like this, but do you see this look at that?
the door
The door is rubbing the side of the microwave
See there. I can't I can't get it closed
I'll get you over here
See how tight that is
Well the other
the other hinges
We're just slightly different
Just barely these these are a little bit further, but
There's an adjustment. I can do on here, and I'm gonna try it on this one cabinet and see if I can't get this to
Work, there's two adjustment screws. There's a screw and there's a screw
That's true. You can loosen or tighten and that'll pull this cabinet door away
From the edge there in case it's rubbing or in case your doors warping. You can have this one out that one screwed in
and if you loosen or tighten that screw, it's not going to loosen up the tightness of your your
cabinet door
To here because that screw is in there, okay?
You tighten or loosen this and that's gonna push this this edge that way or this way
Okay, and so I'm gonna see if I can't get that
Because I don't know which way they've got it attached just yet
Which way it's gonna go let's say
Okay, so I'm gonna
See if I can't get this
Resituated
Get you over here. I
Have not adjusted this yet
Okay, so I'm hoping
That they have this adjusted in the middle so if I tighten this screw
That pulls the door to the right
And if I go to the left
It pulls the door over this way. So I'm gonna go to the right as far as I can
see
There's only so far you can go now and that pulled this whole door over to the right
Okay now
I'm gonna get you in there
And we're gonna see if that door closes. I have not
Checked this yet. So see you're seeing what I'm seeing
There we go. I
Think it's gonna close this time
Here it goes
Look at that
I've got just enough
clearance there
And and if I want it you see look it it's just right now
And if I had to if this was crooked or something
I could do I could do the top over to the left a little bit further, but it's just it's just fine now
You see there that's because I moved this whole thing over by tightening that screw if I loosen the screw
It'll go to the left
Okay
That's how you do that
All right, what's working good?
So you can kind of swing it closed a little bit
You don't have to go like this and then let it let it
Go you bet you can if you want you could you can go just like that and then it's gonna self-close
slowly
Until it's in or you can or you can close it a little harder
You don't want to start slamming it because you could slam it and still
Get it closed all the way
But you know you'll get the hang of it
Okay, there's more. I want to show you so stick around I got more
tips for you
Okay, well I've got
Two more left and that's because I've got this other cabinet door here
And I'm gonna do at a later time. I'm gonna have to pull the stove out just a brand new stove
It's a different type of stove
Front and everything mommy really like this one. I've got it pulled away from the wall right now though
There's about there's about an inch clearance there once I push that all the way back
It's still this door still not gonna open so I'm gonna end up having to pull this all the way out
So I can open this door
Then I can undo the screws
Over there on that side. I'll make a whole video that I'm not gonna pull it out now
And I'll show you how to do it in such a way to where you're not gonna scratch up your floor
Last thing you want to do and see I still have cardboard that cardboard stuff under here from before
They installed that
After they installed the new floor before I took out the old countertops. I put this this thicker stuff
It's it's way thicker. You can get that in rolls
It's kind of comes in a roll like craft paper, but it's a lot thicker. I put that all on this floor all the way
To the front door all the way through here over here on this side put plastic up
I did all that to protect the new flooring before I ripped out the old countertops
okay, and
It was a good thing. I did that because I protected this floor now
I I pulled all this stuff up, but now I have to pull this out
I don't want to you know those legs are plastic
But I don't want to just pull that out and drag it because you'll you'll see you'd be surprised what plastic legs will do
You can you can gouge up your new flooring your linoleum your tile your
Laminate flooring this just happens to be planking vinyl planking. I don't want to make a scratch in here
I'll show you how to do all that later
okay, but
What I wanted to tell you is I got everything done now
I told you that when I installed these it it makes the gap just a hair closer and
generally
On your uppers if you have a style here, and if you have a gap
See initially the gap was about that big these two I didn't put hinges on I'll explain that in a minute
But I had a slight
slightly bigger gap
Than what I have now, but this is fine because that style is in there, but see
This particular cabinet door
Cabinet doors does not have a style does it as a pre-finished?
Cabinet from before and because it was only 24 inches or 30 inches wide as opposed to 3 feet wide
Or whatever it is they decided not to put a style had they have put a style
Then we've been more difficult to try to get everything in and out of that cabinet
This is a better use of cabinet because there's no there's no vertical
Style face frame on there, but if you've got a wide enough cabinet to see how wide this cabinet is
You have a wide enough cabinet
The one to the left is a two foot wide cabinet this three foot wide cabinet
That's why that's why that one to the left did not have a style
What difference does it make on that Joe well?
Here's the difference. Here's what I'm going to tell you
Because they didn't have a style there these doors had very little gap before I changed the hinges
now
Look what's happening?
The doors aren't closing all the way are they
Look at that
See there. They're almost they're almost closing and
They were a little bit worse than this before
But remember how I showed you on this cabinet how to how to slide that all the way over like I did
Okay
By turning that screw I did the same thing over here
I turn this screw all the way to the right
Move this cabinet door all the way to the right as far as possible took that one move that one all the way that way
because
This used to hang over even further
Okay, so I'm gonna have to I got to figure out what to do with that don't I?
You know I'm not gonna shave off the edge of a pre-finished cabinet door
Fooey on that and so what do you suppose? I'm gonna have to do well in one of these cabinets
hinges I'm gonna have to score score and lightly chisel out the edge and
countersink this in that way maybe an eighth of an inch at the bottom and
The same thing at the top, but before I do that. I want to I want to check things out
okay, and
I
Want to check on gaps?
you know
Before I figure out do I want to do I want to move this one closer this way to less of this gap
So it kind of matches
closer to these other gaps I
see this one's a little bit bigger and and
Before I decide on what to do you see here
This there's only so far I want to I want to
Spread this gap, and I want to try to make this gap a little bit bigger if I can now
I'm looking at this cabinet and the edge of the cabinet
Okay, I see. I've got a little bit of room here see about 3 8 7 inch
And I look up here, and I got about 3 8 7 inch
Okay, so that's good, and and so then I'm gonna look
I'm gonna look over on this edge because I've already moved this door over all the way and
I'm gonna look at that and make a determination
This right here that looks like about 3 8 7 inch doesn't it?
That looks pretty good actually
See right there the gap is about the same all the way up
Like there see and so I've got to decide make some decisions
To see if I can make this gap
Bigger and I and I can make that gap bigger if I tighten this and take this door and shove it
Over to the left all the way right I
Don't want to shove this one over to the right anymore because then my gaps gonna get tighter here and over here
But if I wanted to I could probably nobody's ever gonna see that gap over there. Let's just let's just sit here and
Kind of do this
One screw like I say there's only so far I can go
Okay
To the left
and
This is just something
You want to do to make your cabinets look as nice as you can?
Okay, let's push that over to the left a little bit now. I got a bigger gap in there don't I?
Okay, and it's nice and even all the way up
And I'm liking that and then I want to look at the bottoms, and then I can I
Can still raise these these doors up or down
by loosening up that big screw that
The screw that I installed to tighten up the
Hinge to the frame so I can loosen those up, and then I can lift this up just ever so little
to make that
tight or
Before I do that I can look at all the bottoms and get a happy medium on
Do I need to raise this door up or do I need to lower this door down?
Okay, so I still I'm still
on that
On those stages of what I have to do because see here. I hardly have any room here, right? I got oh, maybe
Three sixteenths to an eighth
I've probably got three sixteenths there
But then I look at the next door
And I'm about the same, but it goes up a little bit higher there this door here. See I'm almost a sixteenth
I know this door's got to be raised up
Okay
This one maybe I might need to to lower
But then see that see the gap here this line is about the same as that right?
And so I got about
Three sixteenths there, but then it goes up
To about a quarter to five sixteenths, so what do I do with that? How do I keep that the same well remember the side screws?
these side screws, maybe I just
move the top one and
Get the top of the door move it over to the left
Okay, and maybe leave this door alone
Let's go ahead and do that right now shall we and let's just see
What's gonna happen here?
And see if I can't get that line
Straighter at the bottom, and I'm pretty sure I can
pretty sure I
can
Just get up here and try it
Get this one
See I move that over to the left already
And I'm gonna look at the bottom here
And it looks about
Right, but I can also take this bottom and put this to the right a little bit further
Can I?
Okay like that
And you see I did I did the bottom over to the right. I did the top over to the left
Okay, now now we're gonna look at it
That bottom. We've got just a hair more
Adjustment I could do
But now let's look at it
Okay, I got about the same there
But see this one's lowered down a little bit hasn't it just barely
But I need to move that one over a little bit my batteries running out, so I gotta do this quick
So this bottom
I'm gonna go over to the right as far as I can
And I went at the top over to the left as far as I can okay, and that's that's all I can
Adjust and I've made this line a little bit better now, okay, if anything I could now
Now that I've adjusted that I could now raise this door up ever so
Little to line that up, so there's all kinds of adjustments you can do
Okay, so once once I figure all this stuff out over here
Then I can make a determination which hinge over here
Which hinges am I gonna inset into the wood is it gonna be the left side or is it gonna be the right side?
Or it's gonna be the right side
and the left side
Do you see what I mean, and I'll make that decision after I get all of this other stuff
Complete I've got a few more things to show you so stick around I'll replace my battery and get right back to you
