Leather Journals Made Easy!

Carving and making leather goods
49 followers
3 Video Views·Feb 17, 2026
Hello, welcome back to another video. In this video I'm going to remake these journals,
but I'm going to take a little bit of a simpler approach, maybe make it a little bit more
accessible to the average maker. Here you see these journals that I made in 2018 or 2019.
You see some of the old projects in there, if you can remember that one, the three flip table.
These journals, I made about 20 of those books, but when I made them, I made the interior,
all the pages and everything. This time I'm going to take a little bit of a simpler approach. These
are moleskin journals you can get at mostly any art store. Sometimes you see them at bookstores.
I'm going to do some leather embossing, and this is the original graphic that I made on those
original books years ago. It says, My Inventions and My Evil Intentions. It's kind of a joke.
And now I'm just going to show you a CNC trick here. On my Onefinity, whenever you do a V-cut,
you have to make sure that your plate is level. Now I just run a 10 thou deep border. Now my
graphic has to live inside that border, so it gets two intentions. It shows me that we're on level.
I'm doing the pencil line so you can see it. Now right there, this piece of plywood dips.
I'm going to loosen it and stick in the width of a business card to see if that solves it.
And I have a lot of these. I just punched those business cards out of scrap just to use them for
spacers and notes. And now I run that border again, and I'm just drawing in the pencil,
and that was enough to correct it. So now you could see how level that plate is. If it was
really out of whack, I would figure out how to get it much more level than just with a business card.
Now with some spray glue, I stick down my piece of material. It's just quarter inch plexiglass.
I tape it just for some insurance. I zero my plate, and I just want to let you know that I'm
using from Jenny Bits. I'm just using a 60 degree V-bit from Jenny Bits, and I like Jenny Bits.
They show you the feed and speed typically for that bit right on the casing. Now I run a quick,
I run a quick, this took about 45 minutes, but I meant to say that I ran a time lapse. That's
what makes it look quick. And now this is just some shots off the iPhone just to show you in
real time what's going on. And even these are actually sped up. It takes about 40 minutes to
run this cut, and it's a really tight V-bit in mirrored image. Let's not forget that it needs
to be a mirrored image to make an impression that you want it to read correctly on your finished
piece. And I spray glue it to a piece of wood because we're going to put it in the book press,
so we want to make sure that we got some nice push power behind it. The band saw
there and my camera wasn't on, so that's what I just did. I cut out the blocks. And now I take
them up to the leather shop and I get a piece of veg tan. This is about a seven ounce piece of veg
tan which soaked up all the dye from the piece below it, which is going to be a little bit of
a problem because when I dye the final books, they're going to have a little bit of interruption
and you'll see what I mean. Now this is an old book press from the turn of the century. I have
a few of them. I buy them at garage sales. Occasionally you can get them on Facebook market.
Now I take my print block, wet your veg tan, which is always very impressionable,
especially when it's wet, and I put it in the book press and then I crank down on it.
And I realized the book press doesn't have enough cranking power. This is right where I notice it.
The impression is there, but it could be deeper. You could see it, but it could be deeper.
So I wet it again and I use a piece of wood and I clamp it to the table.
I really should put it on its own stand, which would make it immovable. And you can put the
impression back right on your image. It's not impossible. And now this is a much deeper impression.
Good enough for what I'm doing here for the book. So you can see that. Now this is a difficult
impression because I'm using all that leather has to get pushed back so my letters stand up. So
there's a lot there. So in a minute I'm going to do a different one where it's the reverse.
And I just do a rough cut based on the shape of my moleskin books. You got to keep in mind where
the notebook cover is going to be. And then you can see two of them. And now I'm back at it. Now
this is the bigger one. Same thing. I had to use the big wooden stick to get down the impression.
And I started to realize even though this is a book press, it's not really meant for putting
this type of pressure on top of the leather. So you do have to move it around. So the pressure
really comes directly from under the screw. You get a little bit of flex in the plate. So I move
it around. And you can see I was able to move that one around. And now I'm cutting my leather
covers to the right size. And it's really just a guesstimate. And that mat on the table, I'm
constantly using that grid. It's not just there for show. That grid is very important.
And now I need to skive out where the cover is going to fold around the book.
This really helps. And my skiving knives are a little dull. I should be really cutting slices
of chips off there. I eventually do take them down to the shop and I buff them all.
And it also helps to hammer the joint to really start to train the leather.
And now I'm just giving myself where it gets cut. Again, I'm always aligning to the table,
the lines on the cutting mat. It really, really helps this process. And now I just use a little
weaver chisel to round my corners. And now you see I'm on my way. Because it was wet,
the leather does tend to wrinkle. So all throughout the process, I'm putting it under
weights. So as the leather begins to dry, we want to try and keep it flat. Now these are the thin
books. And you see how it's really a judgment call on how much hangs outside the book. You can
cut it too short. And then all of a sudden, you look like you messed up. So it's a judgment call.
Now once I'm able to establish those two, I use those to copy and use those as a guide for the
other book covers. Leather tends to get pretty hairy inside. So I just use a torch to get rid
of the hair. You got to be careful. You don't want to pause because you'll end up putting a
burn mark in it. So you really got to wand that pretty, pretty quickly. Now I went back online
looking forward to show you a different version. And I found this gentleman's Etsy page. And I
bought this graphic from him for $1.79. And I downloaded it. And I'm not going to sell any of
these. So I'm doing a big one and a little one. And I ran the cut on this old piece of acrylic
that I got from my buddy, Mike. And I noticed that the images were too deep. So I run another
one. But I use, this is another CNC trick. I use a piece of this business card underneath my zero
plate to raise it up. So now the graphic is raised up out of the material a little bit. So that means
I should get more detail. Because you can imagine that v-bit. See that's only 19 thousandths thick.
So I raise my zero up 19 thousandths by simply putting a piece of paper under my zero plate.
So all that detail that got cut too deeply is now at the surface. Which means it's going to impress
into the leather of course. I just ran it again. And that cut took about 30 minutes. So it wasn't
too big of a deal. Now there's the finished cut. And you can see how much more detail is at the
surface. Which means it's going to be in the leather. Using some 90 spray glue. I glue it to a
piece of MDF for the backing. And take it to the bandsaw. And this time I didn't have my camera
off. And you're able to see I'm just running it quick. And in my CNC path I put that little gully
just to accept the bandsaw blade wide enough. I don't need to run a full square around it. That
would take considerably longer. Now the difference between the first graphic and this graphic is now
the image is getting pushed in. In the original book cover the surrounding of the image was
getting pushed in. Which was much more material I have to push in. So I needed much more pressure.
Here you could see the pressure is a little uneven. I put it back in. But you could see
from the first impression I got a nice nice deep impression. Because the whole graphic is the image.
I think that makes sense. Now this is just some Pro-Dye. I think I forgot the name of that stuff.
But you could just run that on. You can get that on the Weaver website. And here I'm just
throwing. The stain really makes these books all wonky. So you just got to let it dry.
And then when you let it dry. Yeah you could see. And what I was talking about earlier is how
this particular piece of leather picked up a lot of the dye and the oils from the piece it was lying
on. So it made dyeing them perfectly even not easy. And now here I'm making sure that I'm
spaced correctly. Based on where my book would be. Now this is the larger one. And you can see
I'm moving it around like I was saying. I keep moving it under directly under the screw to get
better impression. Now I could have taken this over to my other shop and used my big giant
screw press with the big giant wheel on top. I would have got a really nice impression.
But it was cold out. And I just wanted to stay in the warm shop. Now my skiving knives are all
sharpened. So you can see there's no fuzz coming off. It's just nice chips. I took them down to
the workshop and I buffed them all on a giant fast buffing wheel. And it brings them back to
life. I keep all my skiving knives in that shadow foam so they don't bump into each other and chip
the tips. So you could also see I have room on the very end for hole punches. Now I'm going through
all the book covers. I made several when I did these. You'll notice in the end how many I actually
made. I did some traditional book binding. And that's what some of these covers are. So I stained
the book covers. I put the dye on them. I let them dry. And then as they're drying, as they get a
little bit closer to drying, I put them under weights. And that's what I was saying. They kind
of potato chip. And it's hard to keep all these flat. And with the dyes and the finishes we put
on them, they end up smelling like a brand new pair of shoes, which is really nice. It's one of
my favorite smells. I'm using some red here for fun. But you got to keep them flat as they dry.
So I put them under weights. You could even just put them under a book. They don't need a tremendous
amount of weight. Now I'm just using some tough coat. This is some top finish. I make sure I get
that top coat on the open edge because that'll help when I start to burnish the edge. And each
time I do another, you could see that nice little finish there. You see how it's starting to really
start to look like a nice pair of shoes. And you can see a little bit of the uneven tone in the
dye, which is not a big, big deal. Now I'm using my burnishing tool on the edge after everything is
dried. And as everything dries, I'm putting it in the book press or I'm putting weights on top of
it. And you're going to keep seeing that. Now everything's really starting to come to life.
The graphics are really starting to pop. And I made a batch of these just for me and for Rachel
and whoever else comes to my shop. I'm not going to sell any of these. I really encourage you guys
to do these on your own. And if anybody wanted any of my graphics, I could certainly email it out.
Now you'll notice I'm just gluing these to the back. And a lot of people are going to say,
why don't you put a sleeve in there to accept a book cover or a rubber band? Both of those things
annoy me. Because I can use my hands and I know how to do these type of things. If I finished a
book and I still wanted to use the cover, I would just tear it out and glue in another book cover.
I'd glue another journal into the back of it. And then you see how keeping that in the book press
for a couple of hours really helps. It helps with all those finishes, keeping the books flat.
Now these are the smaller journals or rather the thinner ones. And I'm just gluing that back piece
in. And if you want to put a sleeve to accept a book over and over again in yours, you can do that.
Now these are the steel weights. Those broad book covers kept wanting to potato chip. Now my friend
Christina Robertson makes these beautiful end pages for me. So thank you. Occasionally, I use
them. And this is really more of a traditional book bind here. And these book bodies I buy at
Talas in New York, Talas Bookshop. I don't have any relationship with them. I've also found blank
book body journals on Amazon. Just Google book body or book blank and you could find a body in
various sizes and then you'd make the cover. Now this is a little bit of a review. You could see
the stamp that was CNC'd on the Onefinity and the net result pressed into the leather. And I had one
of the journals that I already began to use a couple years ago. These are the traditional book
binds and you could see them and you'll see the end pages in a second. And there's the end pages
glued in place. I've done videos on traditional book binding which I'll link below. But I wanted
to make this video about keeping things a little bit simpler and just simply using existing journals
and then making a fancy cover. Now these make some great gifts. People, everybody loves a journal as
a gift because they immediately feel like they're Mark Twain or Leonardo da Vinci. I know that's how
I feel when I open up a new journal. And don't be intimidated. You just have to start scribbling
in there. Scribble anything. Scribble a to-do list. It gets you going. So you'll notice a couple of
these are brand new. The red one I made specifically for myself. It's already started. Thank you to
Onefinity and thank you to Weaver Leather. And thank you for watching. Go follow me on Patreon.
There's a lot of intimate details behind every video. Thank you all.
