Recover GOLD From Circuit Boards EASILY With This Simple Method

Invest Insight
9 followers
Right guys, welcome back to another Scrap in Irish video and what have I on this one for you. Well
I've been asked a lot about how to remove gold plating from boards or from ram sticks and from
mobile phone boards and stuff like that. I've been asked what method can people use for doing it and
my preferred method is copper chloride. There's two ways you can do it, you can either do copper
chloride or you can do AP and my preferred way is copper chloride and the reason I like to use
copper chloride is when doing the AP method you have to be very good with your, well not very
good, you just have to be accurate, a bit more accurate with your peroxide. If you use the wrong
strength peroxide, too much peroxide in it, it can dissolve your gold and it just means you have an
extra step to go to get the gold back out again. So by doing the copper chloride, the copper chloride
will not dissolve gold. So that's the reason I use copper chloride as the method that I prefer to
do. Again, if you prefer AP or you're a guy that uses AP altogether, fair play, that's what you
want to do. Do it as I always say, do it the way you want to do it and not the way other people do
it. I've been asked what I do, so I'm showing what can work. So I'll be putting in some
contacts from batteries which are like these, the contacts that will be on the batteries. Now
again guys, this is for demonstration purposes only, I don't advise taking the contacts off
batteries because if anyone knows dealing with, especially the lithium iron batteries,
the ones that contain the lithium, like these ones, it can be very dangerous and can cause a
fire and stuff like that. So again, don't advise it, I'm just doing this for demonstration purposes.
Again, I'll be removing the gold from the likes of mobile phone boards, I can use this copper
chloride for doing that. Even copper chloride can be used for pins, for low grade pins I'll
use copper chloride on it, it takes longer on the pins. Again, if you don't know what copper
chloride is, I will link a link up there to it, but I'll also do it at the end of the video.
So don't need to click on it there now, but if you do, come back and watch the remainder
of this video then. So yeah, we're going to be working on them boards. I'll be talking mainly,
I was going to use this video mainly as for the battery contacts, but then I decided to add more
stuff in. So you might see at the start of the video that I'll be saying about the battery contacts,
but then you will see that I'll be adding in mobile phone boards, I'll be adding in TV,
flat screen TV boards, a few RAM sticks, trimmings from RAM sticks, Nintendo game machines have nice
gold flashing on them, so stuff like that. So anyhow, enough chat from me, let's go into the
video and see the results at the end. Again, thanks for watching, as always, at the end of
the video if you don't mind, if you could hit the thumbs up, I would appreciate it, and if you're
already subscribing, maybe subscribing, you'll see how you can get some gold for e-waste. So
thanks guys. Well, it's great to have you back at another Scrapping Irish video, and on this
gold recovery video, we're going to be looking at lithium-ion batteries, or batteries for mobile
phones essentially, some of them will be lithium-ion, some of them won't, and what can we get
off them for gold recovery. So first off, disclaimer and safety notice and all that, lithium-ion
batteries are highly dangerous, shouldn't be messed up by anyone, and this video is just for
demonstration purpose only, so please remember that, and you don't need to do exactly what I do,
and it's just what I'm doing. So on most of these batteries which come out of your mobile phones,
on the older ones you'd have a battery like that, on the newer mobile phones the batteries aren't
removable, this is the older ones, so you can see here we've got gold flashed pins on them,
so I remove them gold flash pins, and then we're left with our contacts that are here,
so we want to make sure after we take off our gold boards and stuff like that, that we're not
leaving anything that can short out, so let me just take this off here so you can see underneath it,
so when we take it off, you can see where there's one connection over here, and there'll be another
connection here, we don't want them two sides touching, so when I take this off, I'll tape up
and I'll keep both of them away from each other, so that we're not ending up with it shorting out
over here, so just remember that, tape it off, put it somewhere safe, and to be stored away,
don't store them in where they can set fire to something, store them in a steel container,
so that if there was ever a fire on them, they're not going to burn your house down,
stuff like that, and then bring them to your nearest battery recycling place, so anyhow,
once I have taken them off, they always have a little bit of gold on them, so again,
even this little bit I took off here, I'll show you now, just want to take some tape off it,
because there's always a little bit of tape on them, protecting the joints and protecting where
stuff had hit off them, so even this little bit here I took off, you can see there,
little dot of gold, very tiny bit of gold on this one, there'll be another little bit of gold
underneath on this side, but some of them will have more gold on them, so for instance,
these are all ones I've taken off already, so you can see here, the gold flashing on the board, so
again, you want to remove any of that plastic that's over them, because you want to expose
the board to all the acid, so any of them ones that have plastic on them, I'll pull them aside
and I'll break them down further, but the ones that have no plastic on them and are ready to
go into the acid will go in, now if you notice, on a lot of the boards there will be little
components still stuck to the boards, so I don't want to put this straight into copper
chloride, I want to get rid of all them little components, some of them will have gold bearing
material in them and some won't, so what I'm going to do, I'm going to give these all a soak
in dilute hydrochloric acid, so that should take all the little bits off and then we should be
able to get it straight into copper chloride, so again, anything that has, I'll just put that into
that bigger jar, that's where they're going to go and I'm going to fill that up with some
hydrochloric acid and we're going to let it work away on them to loosen up any of the little bits
and then once they're all loosened, I can take out the, drain it off, filter it off and get the
boards and get them into copper chloride, so we're going to, first things first, we're going to get
all these into that jar and we're going to start filling that jar up with cheap hydrochloric acid,
so I'm going to be using something that's only probably 10% hydrochloric acid, so it doesn't
need to be awful strong for this, I just need it to loosen up the components so they fall off the
boards and we can get these into the copper chloride then, so let's go outside and let's
add the hydrochloric acid and I'll show you the brand I'm using as well. Okay, so we are outside,
it's just about to start to rain but it doesn't really matter because we'll be finished in a
couple of minutes, so this is just a mortar stain remover that I bought in a hardware store,
contains 10% hydrochloric acid and that's all I'm going to be using on this
is 10% hydrochloric acid, I don't need to use anything stronger, I have my 32% one as well
which I have here but no need to use anything stronger than 10% really just to do what I'm
going to do here, all we wanted to do is cover the metals, let the hydrochloric acid start to
work on the tin, the solder, all them little legs that are holding on them little bits
and then they'll fall off and we'll be just left with the boards which we can put into our copper
chloride solution which I'll be using the 32% hydrochloric acid in, now you can do the copper
chloride in the 10% as well, I have done it, so that's it, I'll just close that up, let that work
away and for probably over a week and it'll loosen up all the little bits and get them off the board
and now some people won't bother doing this stage, some people go straight to copper chloride and
again that's their choice but I prefer to try and make the boards as clean as possible
so that when we get to the gold thing all we're putting, when we're putting the gold into acreage
we're not making sure that all the tin, solder, all that sort of stuff is gone and I don't waste
my copper chloride eating up and filtering out all them little bits out of the copper chloride so I
want to get rid of them first so when I'm filtering I'm filtering out the gold flakes and then the
boards that'll be left will be just put in for recycling, so come back in a week's time or so
Right guys so these battery terminals, I've taken them out of the acid, washed them off and we're
ready to get into copper chloride with them so you can see the gold there, it has like a little
black coating on some of them but I'm not too worried about that, usually when it goes into
the copper chloride that's out of the way anyhow, now I'm also going to be throwing in other bits
and pieces so stuff like these mobile phone boards will be thrown in with the stuff and let
me see what else we have here, so like these trimmed fingers from TVs as well, any of that
sort of stuff they'll all be put in with the terminal so if you do see other stuff in there
don't be panicking I've already said what I'm going to do so like all these little any of these
gold flash connectors they'll all go in there anything that has gold so I'm just trying to
clear out a lot of gold bearing material that I have at the moment so that and I have a lot of
phones like this that need to be cleaned up so I'll probably clean them up off screen and put
them in the acid as well at some stage so you might see them in there floating around and this
sort of stuff I'll also check underneath here in case there's any more gold hidden under the boards
sometimes there can be and so I'll also check them so we're going to get this I'm just doing a
test to double check this one this one's just copper and so and I'll also be just throwing it
straight into copper chloride so I'm not going to show you me throwing it into the copper chloride
and the usual setting up the copper chloride and all that because we've done that loads of times
and if you want to see about copper chloride I'll put a link at the end of the video
and how copper chloride works and what it's used for in gold recovery so go check that out
at the end of the video so watch the video through and then at the end we'll have a link there
for that copper chloride so I'm going to set up the copper chloride go drop these in
I'll let it run for a few days and we'll come back in a few days and see what it's like in
the copper chloride so see let's see how it turned out so far. Right guys I said I wasn't
going to show you the copper chloride bit but I decided to because there might be some people
who haven't watched my videos before and are wondering what I'm doing so I've thrown some
of the stuff already through that I've left to work away you probably can see some gold still
on stuff and then there's gold gone off so like we say that board for instance that was all gold
here but that's all gone so what I'm going to do now is I'm just going to add more boards and stuff
to the solution so I'm going to add anything that's gold plated goes in here so all these
like mobile phone boards are all going in so they all have gold plating on them again some more of
these which are from the Nintendo Wii's so you can probably see some gold floating around up there
at the top there'll be a lot more at the bottom and so we're just throwing all this stuff in
it'll get saturated pretty quick and then what we'll have to do is then filter it out
and any that have the gold hasn't come off we just have to rerun them again
but for the moment it's working away
and these are just this is a mixture of everything there's mobile phone boards there's some ram
sticks gone in there there's some um so again some of the boards only have a little bit of
gold on them and some of them will have a lot more gold on them so but they're all just they'll
all be treated the same way some of them aren't as clean looking but the acid should still work
on them that was a bit of a reaction whatever dirt was on that it reacted with the acid
that's it all nearly in so these are all the boards and some more bits and pieces small little
off cuts with little bits of gold on them and um that is it we let that work away I'll keep
adding more to it as we're going on so as I if I check to see that these are all gone and
dissolved the gold off them we'll add more to them because again I have still and if anyone's
wondering why there's air bubbles a bubbler will help the process to go quicker so that's
oxidization so that will help it to um work quicker so that's all I'm doing in there is that
um I say you probably can I don't know can you see any of the gold flakes floating around
but I can um just try and shake some of them up and see can we get some gold floating up to the
top so I can see the gold here some gold over here some over here floating so it's um floating
around in there all I'll do is cover that and leave it sitting for whatever length of time it
takes to dissolve all that um so when you come back we'll be filtering and we'll be seeing um
how much gold we have so far right guys uh about to filter but I um I know I said I'd come back
once the filtering was done but I was about to filter so I just wanted to show you guys
that some of the stuff has not dissolved completely or the gold has not completely
that means the acid is essentially saturated so it means I have to freshen up that stuff that's
there so um and you can see I'm just going to you can see that there's some gold in here floating
around but there's also some gold still on the boards so that makes it a bit a bit longer process
but it won't make any difference to you guys because um you'll be coming back once I have a
and uh refresh the acid and let it run a bit longer to get the rest of the gold off
so just want to pick out those little sim cards that were in there they've got a little bit of
gold still left on them about that much and again just take out this one so that it doesn't block
the um acid from going down so yeah I just wanted to show you guys that uh before we
um move on to the filter to show you what was in the filter once we're finished
so let's see what we ended up with when I finally get all of those boards cleaned off fully
so you can still see they're still it's fairly loose might come off with a spray so it might
be as bad as I think so I have um filtered out the material and we're left with these filters
well the material is all dry so you can see the gold in there and this one is a bit dirtier gold
but it's still all gold so once it's dry it's just a matter of brushing it in making sure any of it
this can come out without it all I do just brush it out as best I can and any that won't brush out
we can just rip the filter and it can go straight into the acid as is but most of it will come off
the filters so you can see it there gold and then do the same with this one just turn this
around first and see what falls out so you can see the plates and again then you just brush out
the stuff that doesn't come out so again this video was all about showing that what boards can
be put straight into copper chloride uh for releasing the thing because I get asked a lot
of questions how do I take the gold plated off the or the gold flashing from the boards
from mobile phone boards from um anywhere essentially on a on a circuit board that
you see that gold flashing so whether it's ram sticks whether it's on um
there we go so that's it completely brushed out nearly so any old flakes that's left there
they can go into the acid directly I usually do all the filters together
but that's up to you what way you want to do it so that's what we ended up with
from the mobile phone boards from them bits of ram there was bits of um from the batteries
the connectors on the batteries again as I said already don't come mess with the batteries this
is for um educational purposes only that I show what I do I don't say that everyone else has to
do it so what did we end up with from that possibly huge amount of boards zero it I'm not expecting
an awful lot in here there we go one point 1.96 grams of gold bearing material so that can just
go in to the other stuff I've been collecting up so again I just keep collecting it up and
at some stage we'll process all that gold bearing material and this is all from different types of
circuit boards and stuff like that so I know the container is going to weigh a bit so it's 19 grams
it's in there and but the container weighs a certain amount on it so as I was saying that's
let me see what are we there with tv boards with some tv boards we had some
mobile phone boards the terminals from batteries some bits of ram and there was some bits from
nintendo wii's and stuff like that so copper chloride will work on any of that material guys
so again as I said earlier on if you don't know how to make the copper chloride I've linked I'll
link the video at the end and I'll show you that copper chloride I find that's the easiest one to
work with and so I do this because when you're the peroxide as I said the downside of the peroxide is
if you don't get the mixture right peroxide and hydrochloric acid can dissolve your gold
copper chloride won't dissolve the gold so you're safe using it that way so and that's that's that's
it for this video guys so go check out the video at the end if you want to know how to make the
copper chloride and until the next video which I think will be a video for people who want to know
what assets I use because I've been asked a lot what assets do I do I use and stuff like that so
I might redo a video that I've done a long time ago and on the assets and that I use and stuff
like that and then I'll link videos to it for people as well so that probably be the next video
at some stage we'll do another video of using this material in Acarija and melting it down
maybe see what or not melting down but getting to see what we get out of it gold wise
I still am working on pins that I'm working at the moment and so different quality pins there
that I'm working on at the moment and I have a lot of chips that I'm incinerating at the moment
stuff like that so there should be some videos coming soon on a lot of gold recovery stuff once
the weather has improved a bit we'll be doing a lot more gold recovery videos and as you've seen
in a previous video I have melted some gold in the beginning if you haven't seen that
go check it out and so I used a so that's some 24 karat gold tested and I ended up with over an ounce
of gold in total so if you want to go and check that video out I'll probably link that at the end
as well or if not it's probably linked up here now somewhere so go check that out if you haven't
seen it so thanks as always for watching guys and we'll see you on the next one
