Compound Bows How do Cams Work

The Ancient Longbow Legacy
8 followers
5 Video Views·Feb 7, 2026
A description of the four common cam designs is presented. Advantages and disadvantages of each is discussed.
How cams work. The compound bow was invented in 1966 by Hollis Wilbur Allen Jr.
Compound bows make up at least 70 percent of the bow market in the U.S. The numbers are even higher
when we look at bow hunting in America. This popularity is in large part due to the cam
systems on which they work. These cams allow the compound bow to store more energy for the same
peak draw weight than their single string cousins. This gives a faster arrow, flatter trajectory,
and deeper penetration. There are four basic cam designs and we will look at each.
Cams give the archer two main advantages over a traditional single string bow. Through systems
of pulleys, they allow the bow to store more energy for delivery to the arrow, although at
more total draw effort than a single string bow given same peak weight. They also markedly
decrease the effort required at full draw to hold the arrow for aiming. This effort can be decreased
by 65 to 90 percent depending on the bow. Cams are off-center elliptical pulleys. They exert their
force through the center of the limb axles. The bow string sits on the outside of the cam.
A second string sits on the inner cam profile. This inner string is usually called a cable.
Originally, they were made from steel cables. The ratio between the distances of these two strings
from the axle represents the mechanical advantage of the cam and a method identical to a lever.
The larger the difference, the less force is necessary to bend the limbs or to hold them in
position. This ratio changes during the draw cycle, lower at peak draw force,
maintaining for a period, and then rapidly rising at full draw. The percentage drop in draw force
is referred to as the bow's letoff. The graph of a single string bow shows a near linear slope.
The area under the slope is the bow's energy. The graph of a compound bow with the same peak
draw weight has a much greater area and significantly lower holding weight.
The most straightforward cam design is the dual or twin cam. Identical cams are placed on both
ends of the bow. The bow string is attached to both cams and sits on the outer rim. Each cam
has an inner cable that attaches to the opposite bow axle through a yoke. These two cables are
bus cables. This name appears to originate from bus wires in electrical applications.
A bus wire will have one or more wires attached to it to distribute electricity, similar to the
yoke attached to the axles. Most of the bow's force is held by the bus cables. Of cam designs,
dual or twin cam bows can store the most energy for the same peak force. The more energy they store,
the harder the cam and the harsher the draw. This design gives very fast arrow flights.
Having two cams also gives a greater range of acceptable draw lengths. This is particularly
desirable in youth bows. Before looking at the next design, that of single cam bows,
we need to look at the subject of knot travel and cam timing. The grip on a bow is by necessity
a few inches below the arrow wrist. The result of this disparity is that draw force on the bow
at the knocking point is not only horizontal but also vertical. The vertical component means that
there is more tension force on the lower bow string than the upper. This places more force
on the lower cam and limb, with a tendency for the knot to rise vertically at full draw.
On release, the tail of the arrow will now receive a downward vertical force,
placing an upward rotational torque on the arrow. This rotation will cause porpoising of the arrow
and may lead to tail contact with the arrow wrist and erratic flight. Vertical knot placement
between an eighth and a quarter of an inch is recommended to counteract this force.
Any downward rotation is partially negated by the arrow wrist and is preferable to any upward
rotation. Compound bows place the arrow wrist as close to the middle of the bowstring as possible
to try to minimize cam effects on knot travel. If twin cams are not synchronized,
properly timed, knot travel will occur. Poor setup or stretching of the cable can lead to
loss of cam timing or loss of synchronization. This will lead to increased bow vibration and noise,
loss of bow tune, unpredictable knot travel, different force curves for each cam,
and loss of accuracy and precision. Cable stretch has become much less of a problem
with modern synthetic strings and cables. Single cam bows have a single cam at the bottom
and an idler wheel at the top. This design was popularized by Matthew's Soul Cam Bows in 1992.
The bowstring passes around the idler wheel and attaches back at the lower cam. A secondary cam
profile is present for the returned bowstring. A bus cable attaches another lower cam profile
to the upper limbs. Preventing knot travel requires tight engineering between these
three cam profiles. Knot travel is, at least in theory, more of a problem with single cam bows.
However, single cam bows give a much smoother draw, albeit with less energy storage. Single
cam bows are also more tolerant of cable stretch and can require less maintenance. Loss of cam
timing isn't as much of an issue with only one cam. Can't decide between dual cam and single cam
bows? Enter the hybrid. Hybrids became popular with Hoyt's Cam 1 1⁄2 introduction in 2003,
a variation on a Darton Archline. Hybrid cams replace the idler wheel with a second cam.
The bowstring is now attached to the upper cam and continues to the lower cam as a new cable.
This cam-to-cam cable is called a control cable. This hybrid design splits characteristics of the
other two designs. Smoother draw than the twin and faster flight than the single. A lot of
wins went to the Hoyt Cam 1 1⁄2. In 2005, Bowtech introduced the binary cam for final design.
This was, at least in part, also based on designs by Rex Darrington at Darton Archery. This design
uses two identical cams but dispenses with the bus cables. The upper and lower cams are now
connected to each other by two control cables. This design maintains the speed of dual cams,
but with self-synchronization or timing, with the cams slave to each other. There are several
binary equivalent designs by other manufacturers. Binaries are known for smooth draws and fast
barrels. So how do you recognize a cam design? If there is a round wheel at the top of the bow,
this is a single cam. These are becoming rarer with time and being slowly replaced by hybrid bows.
Bayer and PSC still make good single cam bows. If the bow has two identical cams and two yokes
that attaches to the limbs, not the cams, this is a dual cam bow. Dual cam bows are very popular
with youth bows because of a large draw length adjustability. They also tend to be cheaper than
binaries and easy to find design. If the bow has two cams and only one yoke, this is a hybrid.
The cams may or may not be identical in size. They usually are. Binary and binary equivalents
will have two identical cams, but the cables will run from cam to cam. A yoke may be present,
but will not attach to the limbs. Most high-end, great expensive bows are binary or equivalent.
What are people recommending? If your kid is still growing, a twin cam is ideal because of
draw range. Twin cams are also really fast and tend to be less expensive than binaries.
They make an inexpensive, read less expensive hunting bow. Hybrids are a good, again less
expensive choice for a smoother bow. Long hours on the range, target shooting, think hybrid.
Money on your hands, big animal hunts at long ranges, hard to beat the binaries. Acknowledgements.
Designs in this video were drawn loosely from Hoyt PSE and Bowtech cam designs. As always,
thank you for your time and thank you for your attention.
I hope you find something useful in this presentation.
