Relaxing Day Playing With 2000 Degree Glass - Narrated Glassblowing Process

Art Creation
8 followers
Hey everybody, welcome back to the studio. Today we're kind of having a relaxed day in the hot
shop and we're playing around with some new ideas for some new work that we're thinking
about making in the future. And hopefully we're going to make something cool in the end as well.
So I've been wanting to use more black cane in my work. I use lots of white cane in most of my work
but I've really wanted to try using more black so today I figured we'd use some of this black
cane and do a little roll up. But instead of doing the roll up on a collar like we have been lately
we're going to actually do it on a bubble. So we'll start by getting a blow pipe and getting
a little bit of glass out of the furnace here. So this furnace for anybody who doesn't know
is 2,000 degrees and it holds all of our clear glass on the inside. So we're going to let this
first layer kind of cool down a little bit and then here in just a minute I'll actually dip it
back in and get a second layer on top. Now we're going to add one more layer to this but I need to
put a bubble in it before we can proceed. So I'm going to blow into the pipe, cap it with my thumb,
the glass is going to pressurize because of the heat and it takes the path of least resistance
which is straight out of the tip of my pipe. So while the glass is really hot I have a second
to kind of manipulate it and then we're actually going to let it cool down and then we'll put it
back into the furnace to get another layer.
Now while I'm getting that ready we're going to get these canes kind of set up as well.
So we preheated this plate so now we're going to lay the canes across it and let these things kind
of heat up a little bit before we put them into the glory hole. If we do this too quickly and we
don't let these things kind of preheat then everything will shatter whenever we move it over
to the big oven. So now we're going to add that last layer of glass. So now Luke is getting these
canes nice and hot and all fused together while I make sure that my bubble is just the right size
so we can roll these canes up around it.
Alright so that's the last heat. Now that everything is just the right temperature
we can go ahead and go for it. Alright awesome so that went pretty well. I think my bubble was
just a little bit too big so now I need to work on getting those canes nice and lined up without
leaving a gap in between. Oh my god that's annoying. Yeah yeah yeah. Yeah he sold the octopus yeah.
Alright so the canes are pretty close. I forced them with the tweezers quite a bit
and now I think just by rolling on the marver we can really minimize that gap a little bit more.
And also I just want to start to smooth the outside and really get rid of all those little
ridges from each one of the individual canes. So we're kind of killing two birds with one stone
and also I'm trying to force out all the bubbles and make sure that there's no bubbles kind of
sandwiched in between my canes and the base the kind of bubble that we rolled it up on as well.
Well also in that same kind of vein like it's uh I'm trying to minimize this little hole if I can.
Well you've done the sail here right put up a pop up here before. Yeah yeah.
Alright so everything's nice and smooth so now I just need to get rid of kind of the excess canes
right on the tip of the bubble. But I see that if I focus and uh and you know you always want
people to like your work. I'm just trying to diversify things. So now that we have that cut
free we have this nice pattern of canes on the outside. It's nice and smooth. So what we're
actually about to do is we're going to now try to spiral it. We're going to spin all those canes.
Kind of twist it up a little bit.
Now that we've gotten these canes nice and twisted we're going to set it up to go into
one of our optic molds so that we can distort these canes even more. So they're going to
kind of create these little zigzags all the way down the piece or at least that's what
we're intending to do. It's in the house too. You got two? Yeah. Thank you. I thought I had
one out. Apparently I did not. Look that went great. All right as you can see these kind of
distorted the lines a little bit. We put these ribs on it and now we're going to worry about
kind of smoothing it back out so that we can see what the pattern of the mold did.
More than a woman. Exactly yeah. Look you can blow lightly. Off. So it's a pretty cool effect.
You know it really distorted all those lines. Gave us a lot of zigzags. But I think I want to go back
into the mold and try to mess them up and kind of distort them even more. So we're going to set
that up and hit the mold one more time. All right so that distorted our lines a little bit more but
my bubble got a little bit misshapen. I blew a little bit too hard and it wasn't set up exactly
how I probably should have set it up. I think my the walls got a little bit too thin. So we're going
to worry about kind of compressing this back down and getting a little bit more stability and then
we're going to go for making our final shape. It's about pumpkin time. 50 bucks an hour. Yeah I can't
even remember how much he was going to pay us. Yeah it kind of does. So hitting that mold the second time
didn't really go so well and that's okay. You know we almost lost it for a second but we got our
stability back and now we have a pretty cool pattern that's probably going to be really
interesting even though it might not be replicable again. Off. So now that we have everything even
backed out and our bubble is back pretty symmetrical and right in the middle we're going
to go for making our final shape. And I think today the final shape is going to be a cylinder.
We're going to try to make a pretty tall cylinder. Pull it lightly. So we've got some volume. We've got
a pretty good bit of glass at the bottom and now we're going to go for our jack line. So I'm
heating up that area right off the tip of the pipe and in a moment Luke's going to take the pipe from
me. He'll take a big heat and then we'll put our jack line in. For anyone who doesn't know the jack
line is basically a little kind of incision that we use but the jacks is the tool that I have in my
hand and I'm using the tips to make a small little kind of incision right off the tip of the pipe.
This is basically deciding where we're going to disconnect it from the pipe later in the process.
We're going to have to transfer this to a second pipe so we're going to have to break it off of
this pipe a little bit later. So we're basically just putting that little line in there right now
because it's the best time to put it in without losing the piece completely.
Off. Okay I'm just trying to make sure we still had a line. Okay. So I want this to be a kind of
taller cylinder so we're going to start to elongate the piece. I'll give it a little swing. We'll fill
it up a little bit. I'll use my newspaper to kind of even out after we elongate it but I'll really
use gravity to try to make the piece get longer and longer. Oh yeah yeah he came up here. Give me
light air. On. Off. Okay turn. Good. Then you can come here. So now that we've gotten our length
we're going to worry about making our even sidewalls so we have a nice even walled cylinder.
So I'm going to ask Luke to blow through the pipe and I'm going to use my jacks to kind of
guide the bubbles so that the walls of the cylinder are nice and even and symmetrical.
I'll throw my sleeve. Started doing fake laps now. And then we can move on to putting a bottom on
the piece. That sounds fun. Kids have the best laps. Yeah. I like it. All right off. So now it's time to go for that
transfer that I was talking about before. So Luke has a metal pipe in his hand and he's going to
gather a little bit of glass on the tip of it and we're going to use this to transfer it from the
other pipe to this one. That little piece of glass will work kind of as glue so he's going to shape
it up to a nice little dome and get it nice and hot. Bring it over and I can put it on the bottom
of the piece. I'm going to try to put it right in the middle as kind of smack dab in the middle as
possible so it's nice and symmetrical. And then once it cools down a little bit I can add some
water. I'll give the pipe a little tap and it should disconnect and we'll have it flipped over
and transferred to the new pipe. This is what we call the punty transfer. So the punty was pretty
hot. You saw it moved right when I knocked it off. It dropped so Luke was pretty quick
and made sure to kind of adjust to make sure it didn't touch anything and stayed right on center.
He's like hold on hold on wait wait wait I might have missed the point of this show.
So when we transferred it there's a lot of chunky glass on the lip from where it was connected to
the other pipe so now we're going to actually trim all that chunky glass off. I got it nice
and hot. I'll use my tweezers to kind of thin it out and then we can just use my jacks to cut it
off. We'll put a little jack line on it and knock it right off. They say when in Rome do as the
Frenchmen do. Skeletor! I remember there used to be that dog in that movie they named him Skeletor.
All right so now that we've gotten rid of all that chunky glass all we have to do is worry
about finishing the top half of the piece. I'm going to use my soffietta to inflate it from
the inside just by blowing and then I'm going to use my jacks to lift up the lip of the piece
so it lines up with those lines the balls that we made before. The Silmarillion is
like the bible of their world kind of. It's where a lot of things get their names.
It's where a lot of the folklore. Saruman was. Saruman is. He was a god. He is a god.
All the wizards are gods. You can go on. Even the awful one but that's why he came back as
the white. We'll do that again. Saruman was supposed to be. All right.
All right awesome so we've gotten everything smoothed out. Looks pretty symmetrical to me
and now all we have to do is worry about knocking it off the pipe and getting it
transferred to our annealer to cool down. So we're going to add some water to that connection point
right where we want it to break off and then I'll be able to tap it into my brother's gloves,
these Kevlar gloves he has on, and we'll be able to transport it to the annealer so it can cool
down over about 12 hours. Tomorrow morning we can come back and see what we've got.
All right and here's the final result. So you guys can obviously see why I said I kind of want to
play around with these kind of black lines more. The distortion looks so cool with the clear,
the fork around the background. I just love it. And guys if you're interested in purchasing this
piece it is available. You can find a link to it in the description box down below. And thanks for
hanging out with me today. I really appreciate you guys. I can't tell you that enough. Be safe
out there. We'll see you in the next one.
