If you’re seeing the dreaded “Z axis homing failed; the task has been stopped” error on your Bambu Lab A1 or A1 Mini, this video is for you.
This is a real-world, proven fix for a common A-Series issue — not a guess, not a firmware band-aid, and not a “try this and hope” solution. In this video, I walk you through exactly what causes the Z axis homing failure, how to diagnose it properly, and how to fix it the right way so your printer can get back to printing reliably.
This error can completely stop your workflow, especially if you rely on your A-Series printer for daily printing. After spending a lot of time troubleshooting, testing, and tearing down components, I was able to isolate the root cause and get my A1 back up and running — and I’m sharing that full process here so you don’t have to go through the same frustration.
✅ What this video covers: • What the Z axis homing failed error actually means on Bambu Lab A-Series printers • Why this issue commonly appears on A1 and A1 Mini • The specific component responsible for the failure • How to safely replace it without damaging your printer • Tips to avoid repeat failures in the future • Optional “clean refresh” steps while you’re already in there
🔧 Tools & Parts Needed:
You don’t need a full tool bench for this repair.
Required: • The replacement part shown in the video • The two Allen keys that come with your Bambu Lab printer
Optional (Recommended): • A fresh nozzle • A new thermal boot If you’re already opening things up, I personally recommend doing a clean refresh — it’s quick and keeps everything running smoothly.
(Using this link helps support the channel at no extra cost to you — thank you.)
⸻
This video is part of a growing series where I break down real fixes, quirks, and long-term ownership tips for Bambu Lab printers. Now that I’ve got the A-Series printers dialed in, I’ll be moving on to P-Series content next, covering similar issues, maintenance tips, and real-world solutions.
If you’re into EDC gear, 3D printing, or just like learning how things actually work instead of guessing — you’re in the right place.
👍 If this video helped you, hit the like button 📩 Drop a comment if you ran into this issue or have questions 🔔 Subscribe for more A-Series and P-Series Bambu Lab videos coming soon
Bambu Lab A1 Bambu Lab A1 Mini Bambu Lab A Series Z axis homing failed Bambu Lab Z axis error A1 Z homing failed Bambu Lab error 0300-4000 Bambu Lab A1 repair Bambu Lab A1 fix Bambu Lab troubleshooting 3D printer repair Bambu Lab maintenance A1 Mini Z axis error Bambu Lab printer fix 3D printing repair guide
Hey, everybody.
We are back with another review.
Today, we're going to be checking out a little bit of a normal thing that happens to A1 series
printers.
Without further ado, let's hop right to this review.
Today, we're going to be addressing the issue of the Z-homing axis failure that'll either
stop a print or stop your calibration.
I'm going to show you exactly what it is, what you need to replace, and what tools you're
going to need.
I'm actually going to do the replacement here on this A1, which as you can see, is throwing
the Z-homing axis failure code.
First thing you are going to want to do is you're going to want to turn the unit off.
I'll unplug mine because I like to unplug them as well.
Put that off to the side for now.
All the work, it sounds scary, but all the work is really just going to be done here
in the tool head.
To start it off, I'm going to lift up my axis just a little bit so that I can get underneath.
Now, what are we going to need to work with?
Here, let's do this first so we don't mess up our cryo-grip plate.
We're going to swap this one out and I'm going to put on a stock bamboo one.
We'll put the stock bamboo one on that I don't run very often.
The only thing I pretty much don't run on those cryo-grip plates is PETG.
Today, you're going to need the two tools that come with your printer, the little tiny
Allen key and the larger Allen key.
That's all you need.
I actually have a third one here because my provided one is a little bit rounded at this
point.
I have a little magnetic screw tray here with a little bag of screws.
What do the screws come with?
The main problem that is caused from this particular Z-homing axis failure, you look
up on the internet, you look everywhere, you're going to see tons of different things in regards
to things you can do, adjusting the belts, the nozzle, tons of different solutions but
not the actual solution.
What the actual issue is, is a small sensor that is causing the error.
This is a new extruder unit for an A1 series printer.
It comes with the motor which is awesome, comes with the new gear as you can see right
down in there, new gear, comes with a new cutter blade.
It's basically like all the parts that would be needed to be replaced on the extruder are
here including the Z-homing axis sensor which is located right here.
This little black bar right here, this is going to be the sensor for the Z-homing axis
failure.
We're going to see what ours looks like here.
Normally when I replace these, you'll see that they're worn in one particular spot and
there's a copper layer exposed which we're going to see if this one has that.
That's what you would see if you scratched off this black is some copper.
There is a nice little lead wire right here.
Sometimes these get yanked and destroyed so that could cause this as well.
If these end up getting severed or disconnected in some way or I guess vibrated off on the
back which I'll show you here in a second when we replace it, that could also cause
this.
The best thing before you start replacing stuff and taking your whole tool head apart
is to inspect the wires which I'll show you here in a second just to make sure that they're
still screwed in, tightened, and in play because then you can start moving to more
intricate things like pulling off the part with this sensor.
What's nice about the replacement extruder is you got the whole piece here.
It's about $40 and it gets everything that you include here.
What's nice about this though is you are replacing the extruder motor when you're replacing this
little sensor here as well.
The extruder motor, again, it's going to be something that over time after thousands of
hours is going to go so you kind of get to replace everything in one shot.
Now, I tend to have these Z-Ohming access failures more than I have like clicking noises
from an extruder because it doesn't have the power.
I guess you're kind of refreshing everything that you would need to in one shot here.
It's basically going to be a brand new A1 after this.
We have the new tool head extruder part that has the sensor on it.
We also have new screws that came with it so that we can replace these ones that are
on here that I take off.
I'll leave those in the bag for now.
Then the other two things that I'm going to replace while we're in there is going to be
the nozzle and the new boot for the printer.
It'll have new extruder wheel, extruder motor, new nozzle, and a new boot.
Let's start off with the first thing that I like to do is we're going to just pull off
this AMS.
We're just going to put this aside for now because we just don't want that to get damaged
in this process.
Then the next thing I'm going to do is we're going to take off this USB-C cord, which is
right up top here.
I'll scoot this down just a little bit so we can kind of see what we got going on.
There's going to be four screws up top here, which you can pull these off.
I'm going to do all this in real time so if you're doing this, a lot of the times when
I watch videos like this where I'm trying to figure out how to take something apart
that I might not know about how to take apart, it gets fast-forwarded or sections get skipped.
We're going to go through this in real time, so if you want to do this side-by-side, you
don't have to worry about rewinding constantly.
Again, four tiny, tiny screws.
All these screws are going to be essentially proprietary to the holes that they go in,
so when you start pulling screws off, you don't really have to worry about, like, oh
shoot, do I have to remember where this goes?
Not really.
Now that we have the USB-C cord taken off, I'm going to raise up our axis.
Now, we're going to take off the end cap here, which is going to have two screws, one for
the purge wiper and then one you're going to have here for the end cap.
I'm actually going to kind of come around here and we'll take this off.
I kind of have to find the screw, so that's tightening, let's get this nice and loose.
We'll drop that screw into our magnetic dish tray, and then we can remove the purge wiper.
While we're over here, let's take off this little end cap, and again, this is all going
to be done when the printer's unplugged and powered down.
We're going to put that in our electric tray too, then we have our little plastic end cap
that comes right off, and as you can see here, we have our exposed belts.
You can see I have some lubricant here.
If you're in need of lubricating your belt, now would probably be the best time to do
that.
Now, there's a little track here, which has little ball bearings that roll along this
axis.
When we take this off, we're just going to want to be careful that we don't lose those
little ball bearings.
We can take them, pick them up, and then put them back in if it happens, but we don't want
to do that yet.
This is the ... Perfect.
Okay.
What we're going to do now is, now that we have our tool head with the cap off, we're
going to take off the sides of the belt tensioners here, so I'm going to take off the two screws
on the right side first.
I like to hold the extruder head with my hand as well while I'm taking these off, because
we don't want the tool head to slide off, so there's only two on this side.
The reason why we swapped out build plates is, if the nozzle happens to crash into the
build plate, we don't have to worry about damaging our CryoGurt plate.
Here is the end of the belt right there.
As you can see, the two screws that I removed are right there.
We don't have to do anything with this belt right now.
What we are going to do is, we're going to move to the other side, and take off the other
side of the belt.
We have two more screws here, as well as the tensioner screw, so we're going to just hold
the extruder with one hand, and we're going to take off these two screws that are here.
If we can ... There we go.
Screw gone, but good news is, we have extra screws, so I did lose that screw down behind
the shelf here, but that's okay.
I have extra screws, which is great, because that's why they give us this little bag.
Let's pop out this.
We're going to be very gentle here, because there's, again, there's going to be little
ball bearings.
If you pull this off on an angle, that's when you're going to start popping the bearings
out.
You're going to want to just make sure that you're very careful, and you're just going
to want to slide it off as straight as possible.
Perfect.
Here are the little bearings back here.
You can see them in there.
I got a little bit of dust and debris I need to take out, but you can see the little ball
bearings that are in there.
There's two tracks, because there's, on the top and the bottom, two little tracks for
them.
Last thing we're going to do, now that we have this back part exposed, because we took
off these two screws already, we just need to take this one last screw off right here,
which is the last thing that's holding our belt to the tool head.
Let's get this.
We'll get this taken off right now, and then the tool head will essentially be free from
the unit.
A little more.
What came off with this is a little ... I'll show you.
You got your screw, and then you also have ... I can pick it up with one hand.
Here, there we go.
You're going to have this little metal plate, which essentially goes over the plastic when
the screw gets tightened down, so you don't dig into the plastic.
Now we can slide off our belt, and the tool head is now free.
I'm going to come back over here and get this place situated a little bit so we can work
on the tool head.
We got our box for the extruder head that came in from Bamboo.
Now we're going to take ... We have our extruder head right here.
We have our two tools.
We're going to move the purge wiper away.
We're going to bring into play the new piece.
I'm going to leave my screws here because it's magnetic, and it's magnetized to the
bed at the moment.
We have all our loose pieces up here, as well as our new nozzle.
Let's start breaking this down.
Now, as you can see here, my boot is ... Well, my boot's pretty worn, so replacing that boot's
going to be super important, because as you can see here, the entire bottom of the nozzle
is exposed there.
You know what that does?
That's going to be something we're going to cover in another video, which is the blob
of death, and how to remove the blob of death.
Here, we'll get the little one underneath there, because that is a main culprit right
there for the blob of death.
What happens is the boot will end up flapping up.
These little parts that are torn will end up flapping up and catching filament, and
filament will just end up compounding onto the hot end there, and then you'll just end
up getting this huge blob.
We'll end up taking that off, and again, this is something we're going to throw away.
We have our .4 nozzle there, which we're going to take this ... I'll just use a little Allen
key to lift up the gate, which is going to allow me to pull the nozzle right out.
I have a little bit of filament still stuck in the nozzle, which I end up baking these
in a specific oven to get all the filament out and clean them, so I'll do that at another
time.
That's just how this ended.
Now, this is a good opportunity for you to be able to clean up any of the dust bunnies
that might get inside your fan right there, which is, like I said, a great opportunity
for that.
Let's take off this back cover.
Let me grab something that's not going to hurt the back cover.
There we go.
A little pry bar, something like this that's plastic so that you're not breaking these
clips that are back here on the back cover.
I'm going to put that over there by the bed.
The first thing we're going to want to do is, as we talked about on the replacement,
there's these two wires that have these flat stainless ends, and they're going to connect
directly to the main board on the tool head.
As we're looking at them, we can tell that these are not loose in any way, but that's
where it's going to hook up to.
They're not loose in any way, so we know that most likely the sensor is probably bad.
First thing we're going to do is we're going to start loosening the screws to this tool
head board back here, and we're going to get these channels right here opened up so that
we can get the wires, access to the wire channels on the side.
As you can see here, we have wires that run along these channels on both sides which feed
to the main board.
We're just going to start unplugging them.
They all go to the same plugs, so they're not going to be something you can mess up
or mix up.
They're just going to be something that is made for a specific hole, and the cord also
is.
This is going to be your extruder cable.
This one is actually going to get replaced because that's going to go to your extruder
motor.
Let's pop this one up using that little Allen key.
We'll just pry it up.
There we go.
Now we got everything out of the way.
We can see the two wires that we're talking about.
Let me grab my non-rounded Allen key there, and we're going to pull these two little screws
out, and I'm going to put them on my magnetic tray.
Now, I like to leave my Allen keys when they're not in use on the magnetic tray so that I
can get this magnetic effect with these really ... I mean, look how tiny these screws are.
Super tiny screws.
Let's put our big one back on the tray so we can magnetize.
Now that we've unhooked our wires, we can see that's the two port holes that we're going
to be bolting the new one to.
Let's continue to take these three screws off the main board.
Now what that's going to allow us to do, again, really tiny screws.
We want to make sure that we save those.
That's going to allow us to feed this wire back through so that we can swap out the motors.
Basically, we're just taking this front end off, and we want to have access to get this
wire.
All these are going to stay except for this one, but we needed access to that so that
we can take the front carriage off.
Let's continue to keep taking these screws off like this.
Now this is going to be something, again, this is going to be for A1 or A1 minis because
the head tool head is the exactly same for both.
The only difference is going to be the gantries are going to be different and the bed volume,
but everything else pretty much part-wise for the tool head are going to be the exact
same.
This is going to allow us to slide this out just like that.
It's still going to be attached to our ribbon cable.
Now we're not going to mess with that.
We're just pushing this over to the side for now because this is just going to pop right
out through the other side.
Speaking of ribbon cable, we're going to want to take this top part off.
Let's grab our large Allen key and remove these top two screws.
That's going to be attached to our filament sensor.
We don't want to damage that ribbon cable.
It is something that if you do damage it, you're going to need to buy a replacement
part for it.
There is no replacement for that or repair, I should say, for that.
That's going to see our little ribbon cable, very, very delicate.
When you put that back, that's when most people damage that is when trying to feed it in there
and then they screw it down and pinch that, which is pretty devastating.
Let's take off.
Now that we've got all that removed, we know now by reverse looking at this, the new part,
we have to take the two black screws off on the top here, and then we have two screws
down here.
If you look at all these other screws and screws underneath these panels, they don't
poke through to the other side.
You don't need to unscrew anything else except for these two top screws.
I'll show you here in a second.
Once we get this, we're getting the second black screw.
Slide that over there.
Let's put our little sidebars there.
Then we know just by looking at this that it's going to be this screw and that screw
down there that need to come off.
Now when I do the blob of death video, we're going to be replacing this part right here,
which is the hot end nozzle sink.
That's going to be the main part that gets ruined because there's wires back here that
the blob of death will adhese to, as well as the fan, usually needing to get replaced.
Like I said, we'll do that in another video because I have one printer, an A1 mini behind
me that has that issue.
As you can see, I just literally slid that right out.
Because we disconnected that back board, we were able to get this connector to just come
out freely as well, which again, we're just going to put that board back on after we feed
everything back through the hole.
Here's our stock, 2,000 plus hours on this.
As you can see down here, it doesn't look like it's too damaged, but it is faulty because
it's throwing me a Z-axis homing failure error message.
Which we're going to be able to test without even having to run a print.
It'll actually happen during calibration.
So when we run the calibration on the machine, if it passes calibration, that means the Z-homing
axis has been fixed because basically it won't go through calibration or bed leveling.
Anyway, old motor, old extruder, front end right there.
You can see all the buildup in there.
This might be something that maybe just needs to get cleaned a little bit and I can get
some parts off of this for other things.
There's still a gear wheel in there, there's still a cutter, all kinds of parts in here.
So you're not going to want to throw this away.
You can still harvest that for parts, but we're going to put that aside for now.
We have our new unit right here with our brand new sensor and our brand new array of parts.
It looks scary, but it's not.
So here's going to be our ribbon cable, which we're going to be extra delicate.
There's a channel up top here, a little channel where you can rest the cable when feeding
through the motor so you don't like snag that ribbon cable.
Like I said, it's very delicate.
And then you have the final channel, which is the square, which you can leave the ribbon
cable and let that go right through.
Now first thing you want to do before you start tightening this thing down is feed through
our little sensor cable around this fan and underneath this block.
You're going to want this to be in this little channel before we start bolting stuff down.
We don't want to pinch this, as you can see, mine's being a little difficult.
So we're going to use the Allen key to push it into the channel.
And then as you can see here, then we can probably push this down without damaging anything.
As you can see right there, we have our cable coming out right there and nothing else is
pinched.
I checked the other side.
We're checking down here to make sure our fan cable is not pinched as well.
So now we're going to go back through and I want this case to be held on.
So let's put the two top black screws in.
There's the other one, there it is.
And then remember we have our extra bag of screws.
I'm going to reuse the same screws because these are totally fine.
And then I saved those extra screws that I did get with the new extruder.
I might replace some, but for the most part, we're going to save those new screws for when
they actually are needed here.
So let's take our two silver screws that we got.
This one little tiny one is going to go right here in the corner.
And then we have one more.
So we're just going to do all four screws right now so we don't mess up any continuity
and not have this stuff bolted down.
So let's take our other screw and we'll put it in this bottom screw hole just like that.
We'll make sure these are both not gorilla tight, but they just need to be tight to the
point where it's holding the frame on.
Okay, that one was a little loose.
So we have our wires, the thing I did exactly, exactly what I told you not to do is I pinched
that white wire in that little track right there for the frame.
So we're going to have these in the tracks just like that and make sure that we have
all of our wires to our sensors.
So this is going to get fed over the top and then these two are going to come in and then
we have everything ready to go.
We're not going to put our track in yet, but what we are going to do is we're going to
put in our filament sensor.
So we're going to ensure that the ribbon cable goes down the center and then we can pull
that excess with the board right here so that you don't have any slack when you're bolting
this down, which is nice.
We're still going to be very delicate with that ribbon cable, but we're going to use
it to kind of pull the slack down on the top of the tool head.
Now let's get these top screws screwed in.
And like I said earlier, you will know, that's the wrong screw too, you'll know exactly which
screw goes where because they will only fit in the required holes.
So that's one of the, I mean, one of the better things about a BambooLab printer.
A lot of the other printers on the market, they will have, I'm not seeing the other ones,
so we are going to tap into our little extra screws here and I'm going to pull out one
of these top screws here.
A lot of the other printers will have a set set of like maybe all M3 and everything is
the exact same size M3 screw.
And what's nice about this, this is also another great opportunity for you to be able to clean
out if you need to, you can, I mean, look at this layer of filth that came out of my
fan.
So gross, but you're going to want to get all that out of there while you can and pull
all that out.
So got all that little tumbleweed of whatever that is.
All right, so now that we have our filament sensor reinstalled properly, we're going to
go back to the back end over here and we're going to start installing our rear board.
We're going to screw these things down and after we have everything screwed down and
plugged in, then we're going to put on our little flush plates on the side and go back
through putting everything together.
So we know that we want our new extruder cable, our extruder motor cable to go through this
little notch at the top with the ribbon.
So we're just going to make sure that we line that up properly so that it goes through the
notch and does not pinch your extruder motor cable.
That is very, very important right there.
You do not want to pinch that cable.
So as you can see here, there's the ribbon connector right there and then I have it coming
through that little hole right there at the top, which is exactly what you want.
So we're not plugging anything in yet.
We're just going to get our screws and we're going to start putting them in.
We're going to grab our screws and we're going to start putting them in the board to hold
our board down.
Let me get my screw and we're going to put their black, little black screws, not to be
confused with the other little black screws that go on the USB-C cord, those are going
to be shorter.
So if you're looking at them, yeah, they're going to be, okay, and that magnetic dish
is very handy for things like this.
So get these, we don't want them too tight because we don't want to put too much stress
on our board.
So then we know this one plugs into the top.
What's great is the wires, actually before we screw these two in, before we screw those
two in, I'm going to screw in the actual sensor that we just changed.
So let's pop those out.
Now to my, let me make sure I grab the right screws here, it's going to be these little
silver ones.
To my knowledge, you do not need to have a certain one in a certain hole.
I haven't had, I haven't, I don't think I've done them either way, but I usually
will put the one that naturally is, I guess, closer to the side hole, I'll put that one
in first.
So I haven't had any issues with it not working by hooking these up, but I'm not
too sure if there's any type of different polarization based off of swapping these out.
So if you know, let me know down in the comments below, but haven't had any issues with that
as of yet.
So you've got both of them on there, we're just going to tuck that aside so that we can
get this plugged into the main board.
Then we have our other sensor down here, which is for, this is our fan, so this is our fan,
and then here we have our hot end, hot end sink.
Make sure that you line these up and make those connectors go in there perfect.
So you can leave that little heat shield aside, and then we have our cover, which as you can
see is going to go on there, but we're going to get our side pieces put in first.
So let's, this one's going to be for this one, so I'm going to hold this just like
that, and that's going to be our one side.
Now we'll do our other, which, whoops, got that upside down.
You can kind of see how these line up.
There's a little track, this little track, they slide down and then it creates the complete
box.
And then here's our rear cover, which, make sure there's no wires, whoops, wires being
pinched.
Whoops, I got that upside down.
Wires being pinched, and make sure all four corners are snapped in.
Now your head is almost assembled.
We're going to put our new nozzle, put our new nozzle in.
Got our new nozzle, let's put our new boot on the nozzle.
See before you were able to see silver underneath the nozzle, now it's completely covered by
the thermal boot, which is exactly what you want.
Next thing we'll do is we'll put our faceplate on, make sure the faceplate is completely
snapped on.
If you have any bearings that fell out of the tracks, now is a good time to pop those
in because we are about to reinstall the tool head to the gantry.
So like I said, if you, get this stuff out of here, if you have any of those, put those
in now.
So let's pull out everything.
I will save these screws that I have here for later, whoops, I'm walking into the camera
over here, but we are going to take this, get all of our extra parts that we don't need
around right now out of the way.
Here's our old nozzle, put that away, our AMS, we don't want to forget that, and here's
our old extruder, tool head front end, and now let's pull our A1 back over here so we
can start reinstalling the tool head onto the gantry.
So if you remember, the last thing that we did was we took off our screw back here and
then those two screws there.
So we're going to do that reverse, we're going to place our metal plate there, we're going
to grab the longer of the metal screws that we have because that's going to go all the
way into that end part, and we're going to screw that down, we're going to push down
all the way to the end with our finger and then we're going to tighten it, not gorilla
tight, but just tight enough.
Now we're going to put our two screws in here, which is going to allow you to get the belt
on and then, what I said was nice about this is it's completely plug and play, which is
completely true.
I mean, you don't have to mess with anything with the extruder, and then here we are again.
The system corrects itself because if you put the wrong screw in, it just won't stay
in, it'll be loose.
If I can get it out of there, we will get it out of there with the power of magnetism
hopefully.
You know what, here, let's grab our flush cutters and we'll just, I guess, there we
go, just pull it out because those are magnetized too.
All right, now let's make sure we grab the right screw, there we go, and then there is
the left side of the belt attachment.
Now we're going to make sure that our belt is not kinked or twisted, and then remember
those ball bearings because this is when it's going to matter again, so you're going to
be sliding this in and as you can see my beard, I'm trying to get in there with the sight.
All right, let's do this.
I'm actually going to get in on this other side so that I can actually line this up properly.
We're going to pull the tension with the other part of the belts, perfect.
Now we didn't hear any ball bearings drop, so that means we didn't lose any bearings
on the reinstall.
We're going to get our USB-C cable out of the way entirely.
Let's turn our unit a little bit more so that we can get this other side of the belt put
on.
Now you can see our axis moves freely, but we want to get that tension pulled tightly
and then press up that side against the housing so that we can at least get our first screw
in.
I'm going to press the middle of this and if you're looking at this and you're doing
a reinstall on this, you'll know what I'm talking about.
Press the middle.
I know my arm's in the way right now, but I'm really trying to get this screw hole lined
up.
Perfect.
I'm using my thumb to press in the middle so that it's completely flat.
We don't want to...
This is the one I need.
We don't want to cross-thread it in any fashion.
Oops, that is not the one that we need.
All right, so we got our last screw for the belt here.
We're going to screw this last fourth screw in so that we can get our belt tight and ready
to go.
So, tool head moves awesome.
Before we start connecting that stuff together, let's do our end cap over here.
So we're going to take our plastic cap.
Let's grab the shorter of the two black screws and then we're going to install the
purge wiper and choose the longer and we'll install that.
Let's raise this up a little bit so that I can get...
Let's see here.
Make sure that that purge wiper is nice and snug because you don't want that tool head
smacking it on re-entry.
So last two things that we got to do here is we're going to want to take this, screw
this into the top using our smaller Allen key and we have our four little black screws
that are meant for that and we're going to tighten those down.
Again, putting pressure on the bar, you're going to want to support it with your hand.
Again, we're kind of doing this in real time for you so that you can kind of follow along
if you're replacing this.
I mean, there's nothing worse than trying to follow along and rewinding something.
I know it's good for like watch time, but this is that time.
Oops, why is it not around there?
It should be lined up.
I want to just make sure that we get these not too tight.
We don't want them too tight.
If you start seeing the rubber smash, then you put them on too tight.
We don't want this to smash against the bed while we put these in.
Again, that's why we swapped out the build plate so that if we do make contact with the
new nozzle on the bed, we don't chip up any of that cryo grip goodness.
Again, we don't want them too tight.
We just want to make sure that they're just not, it's not going to rip out while you're
printing.
That's the main thing.
For the AMS unit, you're going to want to line up this little notch with this notch
and then this little sensor part and then just slide it.
I pushed up and pushed down, so I didn't push into my bed if that makes any sense.
Speaking of that, we'll lift this up.
Now next thing and last thing that we need to do is we're going to run calibration on
this to make sure that we fixed the Z-homing axis issue.
Let's do that right now.
We'll plug this in and then we will see if it goes through all of the maintenance steps
for...
All right, everybody.
Sorry for the cut here, but I figured it would be a little bit easier if you're able to read
the screen here.
I changed the angle a little bit.
You can watch the tool head as it goes through the calibration sequence and we're going to
actually monitor its progress here as it goes through all the steps.
Let's hit the start button and let it go through the initial calibration.
As we are getting to the end here, we're about two minutes away from the end of the bed leveling
process.
Honestly, if we didn't get to this point, it would have been because of the Z-axis failure.
The fact that we got to this point, the auto bed leveling stage, really lets me know that
this calibration is going to be finishing correctly, which is good because if you have
a Z-homing axis issue, it would not finish calibration.
You don't need to worry about getting a print started or anything like that.
Just run the calibration if you're getting an error when printing.
Sometimes running the calibration might get it to work a couple more times before it completely
kaputs on you and you cannot do anything, whether you cannot calibrate it or print anything.
Just know that.
Running the calibration is really the best step because running that will let you know
if it passes it, then you could probably get another print out of it.
But if it stops and fails, then you know that there's an issue with that sensor that we
talked about on the underside of the extruder.
If you didn't get to see what that was, it's going to be this little black copper-coated
sensor with a little black piece of thermistor tape on there.
Here's the wires for it.
That's going to be the Z-axis failure throw for an error code.
It's going to be coming from that sensor.
We're at zero minutes now for the bed leveling process.
Calibration complete.
We are now 100% ready to rock in regards to firing off a print.
I'm going to go bring this back over, put it on the rack, get the AMS light hooked up
to it, and get my cryogrip plate back on it and get it back in action.
But you just got to see that.
I think I'm actually ... The whole process took about 30 minutes for the calibration.
I might just shorten that down.
I'm definitely shorting it down because it was like 33 minutes just for the calibration.
I'll do the start for a little bit, and then I'll cut to probably the end when I just came
in towards the end of the bed leveling process, but you got to see everything else in real
time.
You don't really need to see the calibration in real time.
It's a waste of your time, basically.
If you have one of these printers, you can just watch it on your own printer.
Anyway, I want you to let me know down in the comments below, what do you think of this
little series of showing you how to fix things on the BambooLab printers, specifically the
A-series.
I have P-series printers that I can also do maintenance and repair videos on because I
do them on a regular basis anyway.
All I'm doing is basically recording it.
I was going to replace this sensor anyway, but I just recorded it for you so that if
you have this issue as well, just know that this is how you solve that solution, 100%.
I've been through tons of troubleshooting with BambooLab, forums, everything, Reddit,
however reliable that is, and everything that I have come up with did not offer me the solution
I needed except for just replacing this housing, the extruder housing.
Again, it's a complete kit, comes with the motor, the front end of the housing with all
the gears and everything you need basically replaced for $40 shipped.
Not too bad if you ask me to get your $200 printer or $280 printer if you got it with
an AMS light back and working again.
Anyway, let me know down in the comments below what you think of this little repair and yeah,
did this solve your problem for your Z-homing axis issue?
Let me know down in the comments below and if it didn't, cuss me out down there too.
Let me know if it didn't work.
So anyway, yeah, give this video a thumbs up and have a great rest of your day.