Quick, cheap and easy. How to fix a Makita jigsaw. DJV185

Tools plus
2 followers
This is one of those problems that can happen with any brand or type of jigsaw. The tool holder stops working or breaks.
Most brands do sell the tool holder or lifting rod so you can repair it. Bit I find Makita one of the best as they make this repair very easy and affordable.
#machine #tools #powertools
Well folks, welcome back to the workshop. Today we have a quick and easy one for you.
Makita jigsaw and repair. This will be a handy one for a lot of people because
a lot of people have cordless jigsaws now and this is a fairly common problem with them.
So this will be a handy one if you have one of these here to fix it yourself.
It's a quick and easy repair which is quick enough and easy enough.
A little bit of work to it but not too major. The problem with it is not the motor.
The motor is working no problem. She's running, she's just not cutting
because there's nothing there to cut with. Cordless jigsaws all develop problems with
the tool holders. It's only the very basic tool holders that give you the least amount
of problems if you want to be bolting under something. The quick release ones because
they're more complicated, more mechanisms to it, it only takes one component to fail
for it to become a problem. But the Makita ones generally aren't too bad to do because
you can buy all the components for them. This one is even easier again because they
also give the option of an assembly. This is going to be how you fix the tool
holder on the Makita 18V cordless jigsaw, the DJV184. It's not the simplest job in the
world but it's fairly easy. Just a little bit of stripping down on it.
These wee cordless jigsaws are actually decently machined to be honest, especially for the
corded, the small cheap corded ones Makita do. You can do them in the Makita colour and
a red version as well. They only cost about €95 for the cheap ones and they're cheap
and cheerful. They do an amazing amount of work. I could use one myself for years.
Cutting rubs out of sheets of ply, marine ply. 8 rubs per sheet, doing about 5 or 6
sheets at a time. Running for hours and the thing running no problem, just kept getting
hotter and hotter. Worked for years, not a problem until eventually the gear stripped
out of it and instead of fixing it we bought a new one instead. We did have the option
of just changing the gear to get it running again but the rest would have just totally
worn out from the amount of work it did. But amazingly workhorse it was. We replaced it
with a bigger version then which was just a beast of a machine. These here wee cordless
ones are very much similar on the inside to the cheap corded ones you get. They're not
high power but they can run for ages. On the inside of her you can see why I say that.
Small motor in it, wee tiny motor. You might think it's very small but basically it's not
that much smaller than the actual Milwaukee one and it's a big machine. This here Makita
one is an actual nice wee slum machine. Small motor but she's just running this here mechanism
so it doesn't need to be massive. What a nice wee setup they are. Switch replaceable,
field replaceable, controller will be one piece, generally that'll be quite expensive but
things like the speed control, battery retainer, same normal Makita crack, all replaceable.
What we need to work on is this here. So if you ever break the tool holder for holding your blade
change it, you have to go this far at least to actually take the machine apart,
take the cover off to access this. That's the complicated bit, this is the easy bit.
Pull out your wee leaf spring, lift this assembly up a little bit,
slide this out, take that all out. Take note of which way it is, there's a wee steel bush
for it to run on, there's also a wee steel bush and a wee seal for it. Some of the more expensive
ones again actually don't even have much of a seal. This one does actually have a little one,
plenty of grease inside of it too. This here is made repairable but it's awkward because of the
way it's fitted, it's fitted this way. Parts for the tool holder you can buy separately like I say
or you can buy it as one complete kit. This one broke off and it has actually sent in the broken
off piece. This here's a whole assembly but I snapped this bit. You can break this apart,
little c-clip down in there, buy the individual components, you can buy this whole tool holder
with this here part that's broken, it's just nipped off or you can buy this as one complete
piece, one assembly, so that's the way we're going to do it today. Now it is good in that
they've actually designed this in a way that makes it easier to repair, having it like this where you
don't have to dismantle the whole thing. If you want you can just buy the whole head quickly and
easily replace it if you have any trouble. The difficult thing about it is the way they've
fitted it. So that there is one piece and it clamps on to this here barrel. So we use a piece
of metal with two bolts underneath to clamp it down but it's fitted that way. There's two socket
heads here and they face in to the body so you can't actually access these unless you strip it
apart and take out this whole lifting rod. That's the only awkward thing about this here, you have
to dismantle and change this. It would have been a lot handier if they could have done it that way,
obviously it must have been restricted for space or something like that there.
So to do it you do have to do a little bit of stripping down but once you get this far it's
extremely easy and this is what makes it very easy and cheap. So you can just replace this on its own,
this whole shaft and keep all the old parts but that costs around a tenner on its own,
this here broken shaft, the whole unit cost 23 plus the VAT, that's the part number there if
you ever need one which you might eventually do if you ever have one of these things.
They do run for a long time, 135941-2. To put it into perspective the bigger version, the corded one,
cost about 60 euro for the whole tool holder assembly, a lot more expensive. This is quite
nicely priced, the only thing it broke off is just that little lip, she's just sheared that off,
not much holding it on, it's actually clamped on as well you see, it hooks on here and that
must have cracked off and eventually worked its way out. All you have to do is take out these
two socket heads, a little clamp, a new band and a clamp underneath and don't muddle up which way
and this piece then is just hooking on and here that it's on the flat and the band goes over the
top and it hooks on to this piece here. It is a little bit fiddly, it would be easier if it was
cleaner, no grease in it. That also makes this very handy because there's no condamnation up
inside the gearbox if this here breaks off, you can just open it and replace it and put it
straight back together again, you don't have to wash it all out, only for this here. Just make sure
these bands are clamped down and in the right position, make sure this hasn't tweaked off to
one side, tighten them down again and there's a new tool holder ready to go back in again.
Nice quick and easy repair.
Awkward bit, it's just getting it all back in again. Take that out, lift this up,
back into the right position and slide this wee bush and oil seam back into place.
And that is it, simple as that. Now, more expensive ones you will get a complete
enclosed gearbox in a metal housing, these cheaper ones and cordless ones generally,
no matter what brand, it's normally just an open gearbox housing that encloses the grease. A lot
of them give you very little grease, this one actually does give you quite a bit. It's decent
actual grease that's in it, looks like a moly grease, but I wouldn't go blowing this out to
clean it like this here because obviously you're going to contaminate that grease.
The dust isn't going to do that much bother, it's already done quite a bit of work already.
2022, next to no dust inside of it. It also doesn't have a problem with grease getting
into the gearbox because of this here seal, which can happen on other models and other brands,
Dewalt especially. The only other thing you need to put in or put back is this little leaf spring,
make sure that's just pressed in down there. It's only just pushing the blade holder back here to
keep it engaged in this roller. The guard here, there's three wee holes down the very bottom,
goes into the third one, that's sitting up tight against the body. The other side just goes down
here, just make sure it's going into the location as you're putting the cover on, it slides together
nice and easily. That should be it, one Makita Jigsaw DJV184 with a new blade holder and as well
one complete unit. That's actually a quick release one as well,
whenever you shove the blade in, it automatically locks on. Nice one. This should also have the
option of turning off the soft start, just like the other model. If you don't like the soft start,
turn it off, turn it on again, turn the speed all the way down and then all the way back up.
There's the soft start, she only runs half speed. Whenever you switch her on,
she's under no load, runs nice and slow. As soon as you actually start cutting in,
it'll ramp up the speed. It's the soft start feature. It's nice for getting started,
nice gentle cut so it's not jumping around the place. It can be very annoying.
I can't say I like that feature myself. Handy to have but problem is a lot of people don't
realise you can just switch it off. They don't like the jigsaw because of that.
Turn it off, just literally, turn up and down the speed, well switch it off and switch it on first
and turn the speed down, turn it up again and that's it off. It'll just run full speed or
whatever speed you put it to as soon as you pull the trigger. A lot handier. I'll just leave it
like that. That's her. As you change your blade holder on a Makita jigsaw, if you ever have a
cordless jigsaw or any jigsaw, if you have a problem with the blade holders, never dump it
and buy a new one. You can always fix them up, especially the Makitas. Two options, buy the
pieces you need for a nice cheap repair or just buy the whole tool holder assembly and drop it
on in one piece. For this particular one, I would recommend just putting on the whole lot because
it's nice and cheap and easy to do. It's a lot more complicated when you get into the middle of
this year and take all these little pieces out because there's springs and pins and all inside.
That can be a bit harder to do but for 23 euro plus the VAT, well worth just replacing the whole
thing. But anyway folks, that's it. If you have one of these Makita jigsaws, that's how you fix
it and change the tool holder. Nice, quick and easy job. Anyway folks, thanks for watching. Hope
you've enjoyed this quick wee repair video. If you're liking the videos, make sure to give us a
like and a follow down below. Anyway folks, until next time, I'll chat to you later.
