Starting a laser business? The learning curve is steep. In this video, Kim and Garrett share the top 10 tips that will save you time, money, and sanity. We cover LightBurn workflow secrets, how to get perfect focus every time, and the hardware hacks that professional makers use to get clean cuts.
Mastering your laser engraver is a steep learning curve, but it does not have to be expensive. This guide breaks down the top 10 things we wish we knew on day one to save you from ruining material and crashing your machine. From manual focus techniques to software coordinate secrets, we are moving you from beginner mistakes to professional results.
Laser Business and Workflow Strategy Focus Calibration: Learn why the factory autofocus often fails and how to run a ramp test to find your true focal height for cleaner cuts.
Material Precision: Why you must trust your calipers over the label. We demonstrate how actual material thickness affects tab and slot design.
Software Mastery: A breakdown of Absolute Coordinates versus User Origin. This is the most common reason for head crashes and ruined projects.
Cutting Logic: We explain the Inside Out rule and how to prioritize engraving layers to prevent misalignment.
Air Assist Settings: The specific logic for toggling air flow to prevent the blowtorch effect on engravings while maintaining clean cuts.
Pro Maintenance: How to use masking tape and the Gorilla Tape weeding hack to eliminate char and speed up post-processing.
Featured Gear The Laser (AEON Nova 14): Our primary machine for high-volume production and large-scale projects.
Laser Software (LightBurn): The industry standard for controlling diode and CO2 machines with precision.
Precision Tools: Digital calipers and honeycomb pins for material stability and accurate measurements.
In This Video You Will Learn Ramp Test Tutorial: How to manually verify your focal point on any material.
Tab and Slot Design: Adjusting files to match real-world material thickness for a perfect fit.
Coordinate Systems: When to use the GPS-style map of Absolute Coordinates versus the laser-pointer style of User Origin.
Warped Material Fixes: Using magnets, pins, and heat to flatten plywood for consistent focus across the bed.
Fire Safety: Essential equipment for your shop to protect your investment.
Efficiency Hacks: Using masking and adhesive tricks to get professional, clean finishes without sanding.
FYI: We are not professionals, and we don’t claim to be. This is what we found worked for our project. Yours may need a little different approach. We have just enough woodworking skill to make some basic furniture. Safety first!
FTC Disclaimer: This is not a sponsored video. All opinions are genuinely our own. This post may contain affiliate links and we earn a small commission if you make a purchase after clicking on my links. It doesn't cost you any extra. Thank you for your continued support to keep Making It!
So you finally got your laser.
You got it unboxed, you set it up, you fired it up,
and you've already ruined $50 worth of material.
It happens to all of us.
The laser learning curve is steep,
but it doesn't have to be.
So today we're going to show you our top 10 tips
on what we wish we knew on day one when we got our laser.
These aren't just settings.
These are hacks that will save you time, money, and your sanity.
So let's get into it.
Tip number one, stop trusting your autofocus.
The mistake, beginners assume that the plunger
or the autofocus is perfect straight from the factory,
but the truth is it almost never is.
The fix here is trust but verify.
Learn to focus with a ramp test
until you know your autofocus is calibrated.
We're going to show you quick and easy
how to run a ramp test.
This is something that's confusing for beginners.
So we're going to show you how to do that right now.
We're going to place a quarter inch piece of MDF.
You can use any wood.
And then we're going to just basically put it on a ramp here.
So we've got three pieces here
so that it's a little bit elevated at this end
and it's flat at this end.
So we're going to start just a cut line
from the top to the bottom
and you're going to have varying focal heights.
You see here it's small.
And as it cuts down here, the focal height gets larger.
The point at which the cut is perfect
is going to be the proper focal height.
So you'll lay it flat and then you'll measure that distance.
Let's give it a go.
Now before I move my board,
I'm going to draw a line so I can put it back in the right area.
Now let's see where it cut through perfectly.
Here you can see we are definitely out of focus down here.
A fat line like this shows that you are out of focus.
So where does it look through,
look like it cut through cleanly?
Up here looks great
but did it make it all the way through at this point?
So let's flip it over.
Where would we say about right there?
Yeah about right there.
So it's about right there.
Somewhere in there.
I'm going to put this back where it was
and now I'm going to bring my laser head to that point.
We're going to use a focal gauge to see what that distance really is.
So we're at about eight millimeters.
That is our perfect focal height.
Let's test our autofocus and see if it's at eight millimeters.
This is what our autofocus is currently set at.
Eight millimeters.
Perfect.
Our autofocus is correct.
Quick tip if your focal height is not correct,
you can easily change it in Lightburn.
You're just going to go over here to laser tools, machine settings,
and you're going to scroll down to focus distance.
Ours is currently set to 7.5.
That works great.
Tip two, trust your calipers, not the label.
Not all eighth inch is created equal.
These are both eighth inch and it's supposed to be 0.125, right?
That's eighth inch.
This one here, this one is 0.118.
And now let's check this eighth inch.
This eighth inch, 0.110.
See, these are two different eighth inches.
They both say eighth inch.
Now, if I'm designing tabs and slots, I'm making big mistakes.
When downloading a file with tabs and slots,
you're going to need to adjust the file to match your material thickness.
Now, if I just assume that my material is 0.125 and the file says it's 0.125,
but my actual thickness is 0.118 like this is, it's going to be all floppy.
It's going to flop around.
So I need to make sure my slot, which is this area that's missing material,
is the same thickness as my material.
And I'm going to need to make sure that my tabs also reflect the thickness of my material.
So we'll just slide this together real quick.
Put these two slots together.
Then we can slide our tabs into these slots here.
Tip number three, stop asking Facebook what the settings are for this material.
Every laser is different.
Instead, we're going to run a material test card, either inside Lightburn or X-Tool Studio.
They're both settings and super easy to do.
Tip number four, the inside out rule.
The mistake is cutting the outside shapes first,
then going to cut the inside shapes or engrave.
The problem is once you cut that outside shape, it's going to drop.
Maybe it shifted slightly.
Maybe it just fell all the way through.
And now your engrave or your cut is going to be misaligned.
The fix, set your layer orders in X-Tool Studio or Lightburn
so that your inner shapes cut out first or engrave first.
This is easy to do.
You can optimize your settings in Lightburn
or put your inner shapes on a different color layer and make sure that has priority.
Tip number five, the air assist and the blowtorch effect.
Air assist isn't just for cooling.
It's for pushing away debris and keeping the flame down.
The rule here for cutting, you're going to want your air assist all the way up.
If you're engraving, you want to bring your air assist down
very low so that it keeps the smoke off the lens and prevents the blowtorch effect.
Tip number six, absolute coordinates versus user origin.
I think this is the number one reason that beginners crash their laser head.
Absolute coordinates means the laser bed is mapped out
and that matches exactly to the grid that's on the screen.
Meaning wherever you place your design on the screen,
we'll cut it exactly in the same spot on the laser bed.
Think of absolute coordinates like a GPS map for your laser bed.
The top right corner of your machine is zero zero.
If your design is in the top right corner on the screen,
then the laser will travel to the top right corner and cut it out.
If you place your design in the bottom left or somewhere else in the machine,
the laser head will travel to the design and cut it out.
Pros, this is perfect for jigs or using full sheets of material.
Con, if you haven't homed your machine correctly,
the laser has no idea where it is and it'll travel right on through the metal wall and crunch.
On the other hand, user origin is like using a laser pointer.
You're telling your machine, forget the map.
Just start cutting right here, right where I'm pointing.
The workflow for this is you jog your laser head to the corner of your scrap wood,
hit the origin button on your controller,
and the software says, okay, this is our new starting point.
But here's the secret sauce.
There's a nine dot grid or job origin.
If you're using user origin, see this green square?
That green square represents the red dot laser pointer on your laser head.
If you select the top left green dot,
your laser will start cutting or engraving from the top left corner of your design.
If you select the center green dot, the laser will start from the center of your design.
If you're a beginner using some scrap wood, use user coordinates.
Line your design up, hit origin, frame it, cut it out.
It's foolproof.
Now, once you get comfortable with the coordinates of your bed,
absolute coordinates is great,
especially if you're using jigs or cutting out full sheets of material.
To be honest, we pretty much only use absolute coordinates.
Tip number seven, you don't have to sand the char off of your board.
So if you're really new, this is something I didn't know when we first started.
You definitely want to use masking tape.
Here you can see that we used masking tape.
The char is actually on the masking tape.
Once you peel the masking tape off, the board is perfect and the char is gone.
Tip number eight, pin it down.
The invisible focus killer.
So I focused in the dead center of my board here.
So I have perfect focal height, but this board is super bowed
and it's at least two millimeters bowed out to the sides.
So my focus is going to be out of focus by the time I get to these edges.
This is an easy fix.
You can use honeycomb pins that you can find anywhere.
You can cut them out yourself or magnets.
I love these magnets.
I got these at Harbor Freight.
I just put a rope on them so I can get them back off the bed.
And we just line it up with some magnets.
Flat.
We recently shared a quick tip on how to get some plywood to go flat.
If you have a heat press and a water bottle, a little bit of steam,
a little bit of heat will flatten that board right out.
Number nine is fire safety.
It's not if you have a fire, it's when.
You're literally using a laser beam and directing fire at a pinpointed spot.
So at any point, a fire could happen.
So you want to make sure that you have proper fire safety materials.
Fire extinguisher truly is your last resort.
You do not want to have to spray this fire extinguisher in your laser
unless you absolutely have to.
You want to start with a simple squirt bottle of water.
Put the flame out, maybe even a fire blanket.
Again, both of these are going to protect your laser.
But if all else fails, definitely use that fire extinguisher.
Maybe yours has Garrett's face on it and put the fire out.
Tip number 10, the Gorilla Tape Hack.
So if you are using the masking and engraving in this particular project,
all of these little squares would have to be peeled off.
But if you're using a little Gorilla Tape,
you can lay it over your piece of material here
and it will help you pull the masking right off.
Oh, look at that.
That did a great job.
All the little pieces.
So just get another piece of Gorilla Tape.
Do the other side.
Oh, yeah, that was super easy.
I know that's your favorite now.
Those were our top 10 tips that we wish we knew
eight years ago when we started messing with lasers.
Those would have definitely helped.
Now, if you ever have any questions,
the Mega Mafia family you see scrolling by here are always willing to help.
You can join us over on our Facebook group.
If you're a top tier patron, you have a super secret top tier patron Facebook group,
the Discord channel.
There's lots of places to get help.
So if you're new, come join the family, the Mega Mafia family,
and you'll have a whole group of people to help you.