The Dark Story Behind the Buick V6 Turbo The Engine That Shouldn't Have Worked

Engine Nation
3 followers
How did a rejected economy car engine from the 1960s end up embarrassing Ferraris and Corvettes at the drag strip?
In this video, we explore the incredible journey of the Buick V6 Turbo—an engine GM sold off, bought back, and transformed into one of the most feared powerplants of the 1980s. From its humble origins as a cost-cutting compromise to its legendary status in the Grand National and GNX, discover how Buick engineers defied conventional wisdom about displacement and cylinder count. This is the story of turbocharging, American ingenuity, and an underdog engine that changed performance car history forever.
#machine #engine
In 1987, a Buick Grand National walked into a drag strip and embarrassed a Corvette.
The Corvette had a 5.7 liter V8.
The Buick had a 3.8 liter V6 with a turbocharger.
The Buick won.
And it wasn't even close.
This is the story of an engine that wasn't supposed to exist.
A V6 that was originally designed for economy cars.
An engine that GM almost killed three separate times.
An engine that ended up becoming one of the most feared power plants of the 1980s.
The Buick V6 Turbo didn't just challenge conventional wisdom about engine design.
It destroyed it.
Let's go back to 1962.
General Motors needed a small, efficient engine for their compact cars.
The Buick division designed a V6.
Nothing fancy.
225 cubic inches.
About 3.7 liters.
It made 155 horsepower.
Respectable for the era, but nobody was impressed.
It was a practical engine.
An accountant's engine.
An engine for people who wanted decent mileage and didn't care about impressing anyone at
a stoplight.
The engine had an unusual design.
Most V6 engines use a 60 degree angle between the cylinder banks.
Buick went with 90 degrees.
Why?
Because they essentially took their existing V8 design and chopped off two cylinders.
It was cheaper that way.
Easier tooling.
Shared components.
Classic GM cost cutting.
But that 90 degree angle created an inherent vibration problem.
V6 engines with this configuration have uneven firing intervals.
They shake.
Buick engineers did their best to smooth it out with counterweights and careful balancing.
But the engine always had a distinctive rumble.
A roughness that purists complained about.
For the first few years, the engine did its job.
It powered Buick Specials and Skylarks.
Compact cars for practical people.
Then something unexpected happened.
In 1967, GM decided the V6 wasn't worth the trouble.
They had plenty of V8s.
Small block Chevys were everywhere.
Why maintain a separate engine family for Buick when the small block could do the same
job?
So GM sold the tooling to Kaiser Jeep for about $50 million.
The V6 found a new home in Jeeps, where it earned a reputation for toughness.
Jeep owners beat on these engines.
Off road.
In mud.
In extreme temperatures.
And the engines kept running.
That 90 degree V6 turned out to be nearly indestructible.
Meanwhile, something was happening in the Middle East that would change everything.
In 1973, OPEC announced an oil embargo against the United States.
Gas prices quadrupled almost overnight.
Suddenly, those big V8s that GM loved so much became liabilities.
Customers were lining up for anything that got decent mileage.
And GM found itself without a modern, fuel-efficient engine to offer in their mid-sized cars.
So in 1974, GM did something humiliating.
They bought the V6 tooling back from American Motors.
AMC had acquired Kaiser Jeep in 1970, so that's who owned the engine now.
GM paid somewhere around $20 million.
They sold it for $50 million.
They bought it back for $20 million.
The accountants were not pleased.
But here's where the story gets interesting.
Buick's engineers had been watching the racing world.
Specifically, they'd been watching what turbochargers could do.
Porsche was using them.
BMW was experimenting.
Turbocharging was still exotic technology in the 1970s.
Expensive, complicated, prone to catastrophic failure.
But the potential was undeniable.
A turbocharger could make a small engine perform like a big one,
without the weight penalty, without the fuel consumption.
In 1978, Buick introduced the first turbocharged V6 in a production American car.
The engine displaced 3.8 liters.
With the turbocharger, it made 165 horsepower.
Not exactly earth-shattering, but it was a start.
And Buick engineers knew they were just scratching the surface.
The early turbo V6 had problems, lots of them.
The turbo lag was terrible.
You'd floor the accelerator, and wait, and wait.
Then suddenly, all the power would arrive at once,
usually right when you were trying to navigate a corner.
The fuel injection system was primitive.
Emissions equipment strangled performance.
Reliability was questionable at best.
Car magazines were politely skeptical.
Buyers were confused.
A turbo V6 in a Buick?
It seemed like a contradiction.
But Buick kept developing.
They had to.
The 1980s were coming, and GM was facing a crisis.
Emissions regulations were getting stricter.
Fuel economy requirements were increasing.
The era of the big block V8 was ending.
Buick needed something to replace the performance image
that V8s had provided.
The turbo V6 was their only option.
Let's talk about what makes a turbocharged engine different.
A naturally aspirated engine can only pull in as much air
as atmospheric pressure allows.
At sea level, that's about 14.7 pounds per square inch.
The engine is essentially breathing through a straw.
A turbocharger changes the equation.
It uses exhaust gas to spin a turbine.
That turbine is connected to a compressor.
The compressor forces more air into the engine.
More air means more fuel can be burned.
More fuel burned means more power.
The physics are straightforward.
The engineering challenges are enormous.
First, there's heat.
Compressing air heats it up.
Hot air is less dense than cool air.
Less dense air contains less oxygen.
Less oxygen means less efficient combustion.
This is why turbocharged engines need intercoolers.
An intercooler is basically a radiator for the intake air.
The compressed air passes through it,
sheds heat, becomes denser, and then enters the engine.
Then there's the boost pressure itself.
You can't just cram unlimited air into an engine.
The engine has to handle the increased pressure.
Pistons, connecting rods, crankshafts, head gaskets,
everything has to be stronger.
Or you have to limit the boost
to what the engine can survive.
Early turbo engines often chose the second option.
They ran low boost on stock internals.
Safe, but not particularly exciting.
Buick engineers started pushing the limits.
By 1984, the turbo V6 was making 200 horsepower.
By 1985, 220.
The engines were going into Buick Grand Nationals,
black cars, sinister looking.
They didn't have scoops or spoilers
or any of the traditional muscle car signals.
They looked like something a businessman would drive.
That was part of the appeal.
A sleeper, a wolf in sheep's clothing.
If you're enjoying this, hit subscribe.
We cover stuff like this every week.
Okay, back to it.
In 1986, Buick made a decision
that would cement the turbo V6 legend.
They introduced the intercooler
as standard equipment on the Grand National.
The previous cars had been quick.
The intercooled cars were fast, really fast.
Here's what the intercooler did.
Without it, the compressed air entering the engine
was around 200 degrees Fahrenheit.
With the intercooler,
that temperature dropped to around 130 degrees.
Doesn't sound like much, right?
But that 70 degree difference
meant the air was significantly denser.
More oxygen molecules per cubic inch.
The engine could burn more fuel efficiently.
Power went up.
Detonation went down.
Reliability improved.
The 1986 Grand National made 235 horsepower
and 330 pound feet of torque.
Those numbers don't sound impressive today.
A modern V6 Camry makes more horsepower.
But context matters.
In 1986, a Corvette made 230 horsepower.
A Mustang GT made 200.
The Grand National was matching
or beating the best American sports cars with a V6
in a midsize sedan.
And the Grand National had a secret weapon.
330 pound feet of torque at 2,800 RPM.
That's essentially off idle.
V8 engines make their power high in the rev range.
You have to wind them up.
The turbo V6 made power
from the moment you touch the throttle.
It pulled like a diesel relentlessly from any speed.
The drag strip numbers told the story.
A 1986 Grand National could run the quarter mile
in 14.7 seconds at over 90 miles per hour.
That was quicker than a Corvette.
Quicker than a Ferrari 308.
Quicker than almost anything you could buy in America.
And remember, this was a four-door sedan
with air conditioning and a decent back seat.
Then came 1987, the final year of the G-Body platform
that the Grand National rode on.
Buick knew it was the end of an era.
So they decided to go out with something special, the GNX.
GNX stood for Grand National Experimental.
Buick partnered with McLaren Performance Technologies
and ASC to build it.
Not the McLaren that makes supercars, a different company.
American specialty cars.
They took the standard Grand National
and rebuilt it into something genuinely terrifying.
The turbocharger was upgraded.
The stock Garrett T3 was replaced with a larger unit.
The intercooler was more efficient.
The engine management was recalibrated.
The exhaust was improved.
On paper, Buick claimed 276 horsepower
and 360 pound-feet of torque.
Nobody believed those numbers.
Everyone suspected they were deliberately underrated.
Buick wanted to keep insurance companies calm.
The real numbers were probably closer to 300 horsepower,
maybe more.
Nobody outside of Buick knew for certain.
What everyone knew was how the car performed.
Zero to 60 in 4.7 seconds.
The quarter mile in 13.4 seconds at over 102 miles per hour
in 1987.
Those numbers would be respectable today.
In 1987, they were extraordinary.
Car and Driver Magazine tested a GNX against a Ferrari GTO.
The Ferrari made 400 horsepower.
It cost over $80,000.
The GNX cost $29,000.
In a drag race, the GNX won.
A Buick beat a Ferrari.
A V6 beat a V8.
An American sedan beat an Italian exotic.
The automotive world noticed.
Let's get into the technical details
of what made this engine work.
The basic architecture was that old 90 degree V6
from 1962, 231 cubic inches, 3.8 liters,
cast iron block, two valve push rod heads.
Nothing exotic about the basic layout.
This was old school American engineering.
But the turbo system transformed it.
The Garrett turbocharger used a turbine wheel
about two inches in diameter.
Exhaust gas spinning at over 120,000 RPM drove that wheel.
On the other side of the shaft,
the compressor wheel pulled in ambient air and compressed it.
Boost pressure on the stock engines
was around 15 pounds per square inch.
On the GNX, it was closer to 17.
Here's what 15 PSI of boost means.
Remember, atmospheric pressure is 14.7 PSI.
Adding 15 PSI of boost essentially doubles the pressure
in the intake manifold.
Theoretically, that could double the power output.
In practice, you get diminishing returns from heat,
mechanical losses, and fuel limitations.
But you can see why turbocharging was attractive.
It was like getting a bigger engine without the weight.
The fuel system was sequential port injection.
Each cylinder had its own injector.
The engine computer controlled the timing
and duration of each injection event.
This was sophisticated for the era.
Most American engines were still using carburetors
or primitive throttle body injection.
Buick's system could adjust fuel delivery
based on boost pressure, air temperature,
engine temperature, and throttle position.
It could adapt to conditions in real time.
The ignition system was equally advanced.
Electronic spark timing.
The computer could retard timing under boost
to prevent detonation.
Detonation, also called knock,
is the enemy of turbocharged engines.
It happens when the fuel-air mixture ignites prematurely
from pressure and heat.
Knock destroys pistons, cracks cylinder heads,
bends connecting rods.
The Buick's knock sensor listened
for the distinctive ping of detonation
and pulled timing back automatically.
The intercooler was an air-to-air unit
mounted in front of the radiator.
Compressed air from the turbo entered one side,
passed through a core of aluminum tubes and fins,
and exited the other side significantly cooler.
The efficiency of this heat exchange
determined how much power the engine could safely make.
Buick's intercooler was decent for the era.
The aftermarket quickly developed better ones,
and that's where the turbo V6 story
gets really interesting, the aftermarket.
Almost immediately after the Grand National debuted,
enthusiasts started modifying them.
The engine responded remarkably well to modifications.
It had been designed with conservative tolerances.
That 90-degree block with its V8 heritage
was overbuilt for its displacement.
The forged crankshaft could handle
significantly more power than stock.
The connecting rods were robust.
Even the stock pistons
could survive moderate boost increases.
People started turning up the boost.
17 PSI became 20, then 22, then 25.
With supporting modifications, fuel system upgrades,
and better intercoolers, the 3.8 liter V6
could make 400 horsepower, 500, 600.
The engine's potential seemed limitless.
The world record for the turbo V6
in a production chassis Grand National
eventually exceeded 1,000 horsepower from 3.8 liters,
from six cylinders, from an engine architecture
designed in 1962 for economy cars.
The aftermarket community proved that the basic design
could handle nearly anything you threw at it.
Why was the engine so strong?
Several factors.
The short-stroke design meant lower piston speeds
at any given RPM.
Lower piston speeds meant less stress on the bottom end.
The cast iron block was heavy, but incredibly rigid.
It didn't flex under stress.
The simple two-valve pushrod design
had massive ports that flowed well at high boost pressures,
and the factory internals were specified
with significant safety margins.
The turbo V6 changed how American manufacturers
thought about performance engines.
For decades, the formula had been simple.
More displacement equals more power.
If you wanted a faster car, you put a bigger engine in it.
300 cubic inches, 350, 400, 450, 500.
The displacement race seemed endless.
The turbo V6 proved that forced induction
could break this cycle.
A well-designed turbocharged engine could match
or exceed naturally aspirated engines
with twice the displacement,
and it could do so while meeting emissions requirements
and delivering acceptable fuel economy.
The turbo V6 Grand National
got around 20 miles per gallon on the highway.
Try that with a 500 cubic inch big block.
The lessons weren't lost on GM's competitors.
Ford had experimented with turbocharged four cylinders
in the Mustang SVO.
That program was less successful commercially,
but it showed Ford understood the potential.
Chrysler had their turbo four cylinder program,
most famously in the Dodge Omni GLH and Spirit RT.
Japanese manufacturers were exploring
turbocharging extensively.
But the Buick turbo V6 was different.
It wasn't a four cylinder trying to be something bigger.
It was a genuine performance engine
that happened to be turbocharged.
It could take the fight directly to V8 muscle cars and win.
That psychological impact mattered as much
as the engineering achievement.
The legacy extends beyond the 1980s.
When Buick eventually returned to high performance
with the Grand National revival concepts
and modern Regal GS models,
they returned to turbocharged V6 engines.
The 3.6 liter twin turbo V6 in the Cadillac CT6 Blackwing
made 550 horsepower.
A direct descendant philosophically
of that original turbo V6 philosophy.
And look at performance cars today.
The Mercedes AMG C63, traditionally a V8 car,
now uses a turbocharged four cylinder
with hybrid assistance.
The Porsche 911 Turbo uses a turbocharged flat six
that makes 640 horsepower from 3.8 liters.
The same displacement as that old Buick V6.
Ford's EcoBoost program,
which put turbocharged V6 engines in everything
from F-150 trucks to Ford GT supercars,
owes something to the proof of concept
that Buick established.
The turbo V6 showed that replacement displacement
was possible.
That engineering cleverness could overcome cubic inches.
That you could have power and efficiency
without choosing between them.
That an engine's reputation was earned, not inherited.
Today, finding a clean Grand National or GNX is difficult.
Prices have risen dramatically.
A GNX in excellent condition can sell for over $200,000.
Only 547 GNXs were ever built.
They were special when new.
They're rare now.
But the more common Grand Nationals and T-types
have also appreciated.
Cars that sold for $15,000 in 1987
now trade for 30 to 50,000 in good condition.
The best examples with documented history
command significantly more.
The market has recognized what enthusiasts knew all along.
These cars were significant.
There's something satisfying about the turbo V6 story.
It's a David and Goliath tale.
The small engine that could, the underdog that won.
In a world that valued size and simplicity,
Buick proved that sophistication
and engineering could prevail.
They took an engine that GM had abandoned twice
that was originally designed for practical economy cars
and turned it into a legend.
The 90 degree V6 that started life in Buick specials
ended up humiliating Corvettes and Ferraris.
The engine that GM sold for $50 million
and bought back for 20
became one of the most revered power plants of the 1980s.
The practical accountant approved engine
became an enthusiast icon.
And that's the thing about engineering.
Sometimes the best solution isn't the obvious one.
Sometimes you don't need more cylinders.
You need more intelligence, more creativity,
more willingness to challenge assumptions
about how things are supposed to work.
The Buick V6 turbo wasn't supposed
to be a performance engine.
Nobody designed it for that purpose.
But when circumstances demanded it,
when the fuel crisis hit and emissions regulations tightened
and the big blocks became dinosaurs,
Buick engineers found potential
where nobody else was looking.
They saw what the engine could become, not what it was.
That's engineering at its best,
finding solutions in unexpected places,
making something greater than the sum of its parts,
taking a liability and turning it into an advantage.
The turbo V6 Grand National scared Corvette owners.
It embarrassed Ferrari owners.
It gave Buick, of all brands, a genuine performance halo
for the only time in its modern history.
And it proved that forced induction
wasn't just for exotic European cars.
It could work in American iron.
It could work in a sedan your grandmother might buy.
It could work in a V6 that nobody took seriously.
Sometimes the most conventional package
hides the most unconventional thinking.
That's the story of the Buick V6 turbo,
an engine born from cost-cutting, sold off as surplus,
bought back in desperation
and refined into something remarkable.
An engine that proved conventional wisdom wrong
about displacement, about cylinders,
about what American cars could be.
An engine that still commands respect
more than 35 years after the last one
rolled off the assembly line.
So that's the turbo V6.
Still hard to believe a rejected economy engine
ended up beating Ferrari's.
If you enjoyed this, subscribe.
More coming soon.
