Direct Action Gear: Spitfire Mk 2 Plate Carrier

Ballistic Lab
1 follower
1 Video View·Jan 13, 2026
Direct Action Gear: Spitfire Mk 2 Plate Carrier
Hey guys, tonight we're going to work our way through another batch of viewer submissions.
So first up is the Direct Action Spitfire Mark II.
It's a Polish company, I've been following them on Instagram for a while, they've got
a lot of interesting designs, however, being from Europe or Poland or however you want
to look at it, it's kind of all the same.
At least as far as my concerns go, shipping is astronomical.
So to get these things and check them out is essentially off the table, which is kind
of a shame, because Spitfire, or not Spitfire, but Direct Action, and I think Hussar, or
however you say it, is another one that I'm pretty interested in, but just getting hands
on them to figure out whether they're crap or not is difficult.
So now that somebody stateside had one of these, I kind of asked if I could borrow it,
and they agreed without question, which was awesome.
So shout out to that guy.
Initial glance, I think quality is fine, but we'll take a look at it and run through the
features of this on the table.
The front bag and the rear bag are disassembled, you guys won't lose any value there, we'll
go through them side by side and show you my thoughts and any concerns that come up.
So thanks.
All right, so looking at the Direct Action Spitfire Mark II, the whole reason I got this
thing in the first place is the viewer asked me if I knew if it was Crye back panel compatible,
and I didn't.
I said, you're welcome to send it my way and I'll check, just kind of jokingly, and he
took me up on it.
But he also reached out to Direct Action and asked them, and the Mark II is Crye back panel
compatible.
So this is the Grey Ghost panel, which at this point we all know is Crye compatible.
This is a medium Spitfire, and the one size fits all Grey Ghosts and it fits just fine.
I have no concerns that a Crye panel would fit.
I guess I forgot, this has to be a thing now, although this isn't a Crye panel, so the overhang
doesn't really matter, but it's pretty flush, very, very little overhang.
All right, so the zippers are nice and concealed by this kind of laser cut ribbon here.
It's not, I mean it is a separate piece, but it's really, it's not, it's not like some
ribbon webbing or anything, it's part of the plate bag.
So it conceals the zippers nicely, I guess helps protect them, more so helps prevent
any kind of snag on the zipper and keeps it from disengaging.
All right, so with that out of the way, we can look at the rear plate bag here.
I can see that ribbon runs full length and protects the zipper.
If you're not using a back panel on here, your zipper is pretty well protected, so you
throw a ruck on it or something like that.
If you had a concern about losing teeth on your zipper, it should be lessened, I guess.
And easy enough to access, but it still provides some sort of security to keep the zipper from
disengaging.
Your cummerbund routes under that ribbon and then a reinforced backer underneath the zipper,
so you have a good portion of access here that we got four inch cummerbund over here,
I'll show you in a little bit.
So you've got at least four inch of pass through there for your Velcro style cummerbunds, which
I think I've been calling Faro style, probably wrongly, but that's what I've been doing.
As far as the back panel goes, you do have a single row of webbing up top here cut into
the material, so you can provide some redundant security on the back panel, which I encourage,
especially up top.
The bottom is kind of take it or leave it on back panels, in my opinion, depending on
what you're carrying on the back panel.
But it's nice that it has that there so that it can engage with the MOLLE on the back panel.
All right, on the sides of the bag, you've got these little webbing retainers here.
You're not going to fit too much in there, but like a Harris 152 whip antenna would fit
fine, I believe, and it would keep it nice and rigid against the side of the plate bag
if you had an antenna relocator.
There's not really a way to secure it on the bottom.
You probably have to get creative with some rubber banding around the webbing here to
keep that in place.
But with that said, there is kind of a pass through on the plate pocket here, so you could
run your antenna remote cable down through the plate bag and out the bottom here and
then back up with the antenna on there.
So it could be a fairly clean setup.
You would just need to secure it at the bottom somehow, otherwise your antenna is just going
to fall out.
I've had that happen a bunch of times and it's super annoying.
Up top, it's all, you know, kind of one piece construction here.
Your rear shoulder strap attachment is sewn in essentially to the plate bag through the
wonders of laser cutting.
So it's a nice continuous piece and then box stitched there.
Looking at the inside of the plate bag, you've got a loop type material here.
It's really very felty.
I don't know how well Hook would stick to it.
We can try it out here.
Hook would stick well enough.
So you could put pontoons or something in there if that's what you wanted, or the armor
vent type stuff.
Granted, armor vent wants Hook, so you'd have to solve that issue there.
You've got medium eSappies and backers in here, and you can see they hang out on the
bottom a little bit, but the way the plate bag secures, you've got loop Velcro on your
flap so you don't have any exposed Hook, which I do think also means that it's not going
to play well with most of the danglers out there.
I'd have to double check on that, but I think most of the time the plate bag is the Hook
and then internal is the loop.
But it is a nice long flap here, so even though you've got that much loop hanging out, you
really don't have any concerns with continuity there.
You can see there's a good bit of overlap.
Along the bottom of the plate bag, you've got some MOLLE webbing cut in there so you
can have some horizontally mounted pouches or some arts and crafts for tourniquets or
whatever you want to hang down there.
I don't get super big on that, so I'm sure there's more possibilities than I'm aware
of.
Looking internal on the plate bag here, you can see they cleaned everything up pretty
nice.
You've got your Hook Velcro there, stretch panel on the plate bag, so it should breathe
fairly well, as well as accommodate some goofy sized plates without too much question.
Really the only issue with the eSappies there was height, and that may just come from the
backers, I'm not sure.
Let's see what we've got.
We've got some quality control tags here, and I don't know, part number or something.
Nothing else really to write home about inside the plate bag.
You can see it's pretty simple in there.
You've got all the business piece laser cut with some Velcro on top of it.
I'm not really sure why they put a grommet in there, I don't know, maybe that plays well
with something else they have.
And then your stretch panel sewn in there.
So that's the rear bag.
You do have a nice built in drag handle, which has kind of been laser cut and sewn in there.
I don't know how resilient that would be, but if you can grab a shoulder strap, grab
a shoulder strap, and that should solve most of your problems.
All right, so we'll get the rear bag out of the way.
And you can see, made in Poland there, maybe, maybe you can read that, I don't know.
It's made in Poland.
Front bag is not as sloppy as it seems, I've just got one of the P210s in there so it's
easier to move around.
So you've got nice laser cut bib portion here, so you can mount your end user devices and
what have you.
And then a zippered admin pouch, which doesn't run very deep, runs to the top of this Velcro
here.
There's no organization in there, it's just lined with packed cloth.
Which isn't a huge deal, not my personal preference, but I get it, whatever, it adds cost and time
and complexity.
I'm not a huge fan of sewing in zippers on admin pockets.
They just restrict the opening a lot, I don't know.
The Axel one, for whatever reason, because it's mounted in there with Velcro and not
part of the plate bag, seems to work pretty well, but like this and the Armadis 2 and
whatnot, when you have the zippers sewn into everything else, it just is a little restrictive,
especially when it's this narrow.
You've got a webbing loop here, so you could mount your push-to-talks if you wanted to.
If you don't have an end user device, obviously you can mount it to MOLLE.
You've got a similar routing webbing piece there, so you can wrangle some comms wires
at least a little bit.
You also have holes cut into the sides of the plate bag.
I was looking at these earlier, and I don't know what you would use those for other than
potentially some cable management.
I don't know how it would possibly tie into anything else, but I guess if you wanted to
do a one-man cummerbund, you could improvise and just run it through the plate bag and
have a buckle on each side, and then run that to the back.
That would have to be a custom job, I believe.
Not that it would be a hard one.
You could do it just off the shelf with burning the ends of some webbing and stuff, but it
would have to be homemade.
I've got one-inch side-release buckles for your placard compatibility here, and then
they're protected by this little elasticized piece here.
You also have some MOLLE cuts running underneath there, so you could use that for some further
push-to-talk mounting if you didn't need side-release buckles.
Shoulder straps coming up are fold-over design, so it's a single piece coming off of the front
plate bag, and you open it up, run it through the rear bag, and then secure it back on itself.
I like that they didn't split the hook and the loop 50-50, so you have room for adjustment
there.
If you've got some gigantic chest or whatever, you can just close it like that, and then
if you're a normal human being and you want to tighten it up a little bit, you can pull
it down further.
You could go further if you wanted.
You just start losing your hook continuity there and have some excess strap hanging off
there.
Looking at the shoulder straps a little bit more, you've got more routing.
I'm a big fan of that, especially sewn in to the straps, and then some more of that
kind of felt-like material underneath so you can stick some pads if you wanted to.
I'm not quite sure what the little overhanging ribbon piece is here, because it's not...
It's kind of hollow, but it's not of enough size to matter.
I don't know.
It's part of the construction, I guess, left over.
And then on top of the strap, you've got some elastic as well as some kind of hidden molly
routing there.
So if you were feeling really squirrely and frankly dumb, you could put your push tuck
up here if you wanted, but you could use it for cable routing for sure.
I don't know if you could get it to play with G-hooks successfully, so that's something
to be aware of.
In all honesty, with this being kind of sewn in, and I don't think these are repair buckles...
Are they?
Nope, they're repair buckles.
Alright, either way, with the mounting spot kind of being fixed and no aftermarket support
for these things, I would probably just go ahead and source my placards from Direct Action
too.
But, you may not like them, that's fine, whatever.
Internal is the same as the rear bag with the pontoon capability there, and then again,
the molly along the bottom.
And then the gentleman that I borrowed this from sent me two cummerbunds.
This one, nothing to write home about, but it's a fairly straightforward elastic cummerbund.
No big deal.
It's got a nice pull tab on it, so you can get it off on the front end.
And then the Velcro area is fairly small, but that does give you a lot of room for adjustment
both in height, so you can get your rear bag where it needs to be, as well as depth.
You could butt these all the way up to each other and really suck up a lot of length on
there if you needed to.
And it is, I believe I saw it, no it's not going to do it, it's a single piece elastic.
I thought I saw it split there like it was double, but it is a single elastic there.
So not overly strong, but that's fine.
If you're running a light load, that might work for you.
And then, I think this is their more premium cummerbund here.
So I forget which buckles these are, whether they're Tactic or Rock, I can't remember.
But they're not tubes, they're the short throw vertical tubes, so they're kind of the happy
middle ground.
It doesn't take much depth to disconnect those, only about a half inch or so.
So they kind of, they serve the same purpose as the ones that require no vertical throw
and just separate side to side.
You've got your front mounting here with the back having a little bit more surface area
than the front, which is kind of nice.
If you're lifting your placard, odds are this will stay on the plate carrier itself instead
of the placard.
And then you've got a full molly field on both sides, or I'm sorry, on the exterior.
Interior has a stretch pocket here.
I had it opened up and it closed on me, I apologize.
There's really good Velcro continuity there.
It's not going to open up accidentally on you.
I think you could put the Crye armor panels in here because it's kind of bellowed on the
bottoms here.
So I think you could fit the 6x9s in there.
The front portion here, the Velcro is not sewn straight to this, so there's a little
lip in there that you could work the armor under if you wanted that in there.
I think that would fit the 6x9 panels just fine.
Or you could put some Velcro inserts in there if that was more up your alley.
I think you would have good luck with that.
It's like an inch and a half strip of Velcro in there, so it would hold an insert just fine.
Just keep in mind, depending on how the insert is constructed, you might wear through this
tweave with whatever you're carrying in there.
And then on the back end, it is still Velcro, which is not my preferred mounting method
for cover buns, but this has kind of a nice stretch built into it where it's reinforced
with this ribbon here.
So when you get to the extent of the stretch, it keeps you from destroying your elastic
there too much.
But it's got a good bit of stretch in it, and it's not overly weak, so it doesn't just
immediately give you all of the stretch.
Looking at the quality on these things, the buckles are not my preferred buckles, but
I understand first fear sometimes can be a little difficult to work with on getting tubes.
Mixed results.
I have bought tubes to have on hand without issue, but other people tell me it's a nightmare.
So that's something to consider, maybe it's just easier to source these in Europe, which
is totally feasible.
The stitching looks alright.
This elastic you can see, when I pull on it, it's a little worn, I don't know if that shows
up at all.
Over here, I don't know if that's just through use, or if it's a slightly lower grade elastic.
It feels fine, and if I hadn't stretched that out, I don't know if I would've noticed it.
The laser cutting looks good, the materials all feel right.
I didn't check it under night vision, just because, I don't know, that's a lot.
So if that's a concern, I don't know, plan ahead and check it out.
But if that's a concern for you, probably just buy American-made stuff would be the
better option.
Other than that, all the materials feel good, Velcro feels good, stitching looks good, I
didn't see any major concerns in here.
We've got some bar tacking, some box stitching, I hit on it before on some videos, but the
corners of the plate bags look well done, they're all finished edges and everything.
I don't have any complaints about this.
Having seen it, I feel more comfortable that if I see something from them that really catches
my eye, I can jump on it without too much issue.
I will say, I think they're on Mark IV now.
They still offer some of the old versions, I don't know all of them, it's been a while
since I checked their website.
So Mark II is Crye compatible, and I think they've gone back and forth throughout the
different versions.
So Mark III might be proprietary, and then I think Mark IV they went back to Crye pattern.
But again, if you have any questions about that, obviously reach out to Direct Action,
the owner of this did, and he got an answer I think within a day.
So if you're looking at the Spitfire, just give them a heads up, say hey is the Mark
IV or the Mark III Crye compatible, I'm just curious, and they'll get you an answer.
But yeah, there you go, that is the Spitfire Mark II with two cummerbunds.
Hopefully you guys got something out of this and feel a little bit more comfortable dabbling
with European gear.
Thanks guys.
