Jason breaks down how to pick the right Wilwood brake kit for your lowered F100. If you're dropping your truck more than 4 inches or running an FFG Level 2 or Level 3 chassis, the 7" booster kit is what you need. Standard ride height or mild drops? The 8" booster works great. Here's how to know which one your build needs.
We've done this brake upgrade on hundreds of classic Ford trucks. The main issue with lowered F100s is simple: when the suspension comes down, the engine comes up. That Coyote motor starts crowding your firewall, and suddenly an 8" brake booster won't fit without hitting valve covers or other components. That's why we developed two versions of our Wilwood master cylinder kit—same stopping power, different packaging for different ride heights.
Jason walks through both kits in detail: the firewall brackets, pushrod lengths, booster sizing, and why the 7" dual diaphragm booster solves the clearance problem on slammed trucks. He also covers the technical stuff that actually matters—pushrod preload adjustment, pedal ratio considerations, vacuum requirements, and when you need an adjustable proportioning valve. This isn't just theory. We run these exact Wilwood brake setups on our shop builds. After years of Coyote swaps and custom chassis installs, we know what works. If your old single diaphragm booster and manual brake setup isn't cutting it anymore, this kit gives you modern stopping power that actually fits.
The 7" booster kit is designed specifically for trucks that are low—airbagged, coilovers, or sitting 6 inches off the ground. It uses shorter firewall brackets and a compact booster to clear tight engine bays. The 8" booster kit works for standard or mildly lowered applications where you've got more space around the engine. Both use the same Wilwood 1" bore tandem master cylinder that delivers the brake pressure you need at the calipers.
Jason also covers common mistakes: skipping the bench bleed process, getting preload wrong on the pushrod (that critical .010" gap), and mismatching your pedal ratio when converting from manual to power brakes. If you're running 37" tires or big power, this kit will nearly throw you through the windshield—in a good way. But it all comes down to getting the components matched correctly.
WHAT'S IN THE WILWOOD BRAKE KIT:
Wilwood Tandem Master Cylinder (1" bore, lightweight die-cast construction) Tuff Stuff Dual Diaphragm Booster (7" for lowered or 8" for standard applications) FFG Custom Pushrod (shortened for 7" kit, standard for 8" kit) Firewall Plate & Grommet for clean installation Mounting Brackets designed for your ride height Optional: Wilwood Adjustable Proportioning Valve for disc/disc or mixed brake setups
TECHNICAL SPECS JASON COVERS:
Why 7" vs 8" booster matters for lowered trucks Pushrod preload adjustment (.010" gap requirement) Pedal ratio for power brakes (5:1 or 6:1 target) Vacuum requirements (16-17" minimum) Brake pressure targets (700-800 PSI at calipers) Proportioning valve setup for rear brake control Bench bleeding master cylinder process
This kit works on 1967-79 Ford F100 trucks and 1978-79 Broncos. If you're building on an FFG chassis or doing a Coyote swap, this is the brake upgrade that makes sense. Stop guessing about bore sizes and booster clearance—Jason explains exactly what you need based on how your truck sits.
Got questions about which booster size fits your setup? Drop a comment with your truck year, ride height, and engine—we'll help you pick the right kit.
More brake upgrades and lowered truck tech coming soon. Follow @fatfendergarage on Instagram for daily shop content and subscribe to see what we're building next.
Hey everybody, I'm Jason with Finner
Garage and we're talking about brakes.
And so one of the things that I have
learned is brakes are really important.
And the reason why I've learned that is
I've had some not so good brakes at
times. And so and also the ease of
installing good brakes also becomes
difficult. So braking is really
important. And when you're driving your
truck, having the right components that
go together to make it work are really
important as well. And so there's a lot
that goes into brakes. there's uh brakes
that you know that you you'll get a
little bit confused on getting like
mismatched parts and then you wonder why
your brakes don't fit. They're not
working correctly and so it becomes a
little bit of a struggle. But I have
used this setup with trucks with 37in
tires on them and it nearly throws me
through the windshield. So, but it all
comes down to just getting things
correct. And so if you're unsure,
definitely you can call Wheelwood.
they'll steer you the right direction
because a lot of it has to do with the
right size bore you have in your master
cylinder and everything else then comes
down to brake pads and the right
pressure you're getting at the m at the
calipers. You got to have the right
pressure. You got to be close to like 7
800 PSI and a little above that to
really have good brakes. Of course,
vacuum makes a difference. Does your
engine have enough vacuum that the
booster is working? So, you need at
least 16 17 in of vacuum pressure in
order to get a booster to work well. So,
if you have all of that, then it's very
easy to make your brakes work good. But,
let's talk about this. So, a lot of the
old manual brakes from like your 67 to
79 Ford pickup trucks, you'll have a
great big single diaphragm booster if
you have one. You got this really old
non I don't want to say it non-disc
brake in a lot of these. And so trying
to find a way to convert it over and get
better brakes is really important. So
we've developed this kit. Now, this kit
comes in two options. And the one I'm
going to show you is for trucks that are
really low. And um what we've learned is
when we're trying to fit a Coyote motor
and we've got it super low, either it's
airbagged or it's 6 in off the ground,
that engine comes up. And as it gets up,
we start getting crowded on space. And
so location, location, location becomes
really critical. And so we have to go
down to a 7-in dual diaphragm brake
booster. We got our Wheelwood master.
And then we've got the brackets and the
push rod. So I'm going to kind of show
you what's required to make all this
work for us. And then we'll show you it
installed. It works great with our
chassis cuz the engine locations in the
right spot. And this kit helps us
accomplish that. So if you have one of
our chassis and you got level two or
level three, you're going to want this
kit. So, this kit right here comes with
these firewall mounted brackets. Of
course, you're going to get the hardware
to mount it to the firewall. And then
you're going to get a little brass
bushing that's going to go right here.
I'll pull that out so you can take a
look at it. So, you're going to get this
little bushing right here that goes it
gets pressed in here. I don't want to
press it in too hard cuz I won't get it
back out. But, that'll go in here. And
then this will be the pivot on your on
your brake pedal right here. And then
you'll you'll thread this into the
master brake booster push rod. So, all
right. So, let's let's pop this open.
And the other kit that we have, these
brackets stick out a little bit further.
And because it's a like a level one,
it's not super low. We actually can give
you an 8 in brake booster. And so, more
clearance around the engine. When the
engine comes up, we lose clearance. So,
here's a Wheelwood master cylinder kit.
And you can purchase it with or without
a proportioning valve. That's an option.
Uh we don't we're not showing that uh
with this particular setup, but there's
a proportioning valve that you can get
that will install here and you can
control and regulate brake pressure to
the rear brakes. And so why do we use a
proportioning valve is because we want
to basically put as much pressure as we
can everywhere, but we also don't want
to lock up our rear brakes, right?
right? Cuz that's going to turn into a
slide. So, you want to be able to adjust
that when you hit the brake pedal super
hard, your brakes lock don't lock up and
you keep them from locking up. So,
you'll kind of do a couple test runs and
if your brakes lock up under hard
pressure, then just adjust the
proportioning valve so that you can
actually keep them from locking up.
You're going to be using about 75% of
the front brakes anyways. And so, you
want to make sure the ratios are
adjusted. And so, you might have drum
brakes on the back or something like
that. And so, you'll have to adjust
that. All right. All right. So, you're
going to get this Willwood master
cylinder. Now, with this Willwood master
cylinder, this kit, you see this little
push rod right here? I don't want to
open it up, but you got this little
bullet right there. So, that little
bullet push rod, do not forget to put
that in here. Okay, that goes in here.
Next, we'll open this up.
All right. So, here you go. These
brackets are going to mount
here,
and then they're going to install on the
firewall. Pretty easy. Not too
difficult. But that's going to be
mounted to the firewall. Then this is
going to mount right here. You'll take
that off and you mount this here. Okay.
Now, there is a little bit of a trick.
This right here is adjustable. You can
thread this in and out. And we actually
have a little bit. We got another video.
We talked about this a little bit more
in depth. But this distance from here
and this little bullet right here when
they when they are pushing against each
other can't be too big and it can't
touch. If it's touching and you go to
push this on and you start pushing this
for this to mount that's called preload.
And so you're preloading brake pressure
on your brakes and which means your
calipers are already starting to have
pressure. And so if you get too much
preload and then as the brake fluid
starts to heat up from use use, it
continues to expand and you get more
preload. So you have to have right
around 10,000 of an inch gap. Now we do
sell a tool, but a tool we have that
will measure the distance between this
and this so you get that set up
correctly. It's very very important that
it's not too big of a gap to where you
have to push your pedal a long ways
before you get the brake booster or it's
too small of a gap and it's causing
preload. So you're going to want to make
sure. So, this right here, this 7in
booster works great pretty much on all
these trucks. Again, we'll go to a
larger 8 in if we can, but we've used
the 7 in on a lot of these lower trucks
and they stop great. But again, it comes
down to the right size master cylinder,
understanding what size rotors you're
running, and understanding what size
calipers you're running. And so,
sometimes, uh, occasionally you have to
change out this for maybe a little bit
larger diameter bore. So right now it
comes stock with a 1 in which pretty
much will cover the gamut of most
everything. Occasionally you may have to
go up to inch and a16th or inch and an
eighth. Those options are available but
don't do that just as a I need to change
it. It's not working. Call Wheelwood.
Have them evaluate your rotors and your
master cylinder. Often times it's really
important they make a gauge you can put
on your caliper and you can check the
brake pressure you're getting. Sometimes
it can come down to your pedal ratio.
And so maybe your pedal ratio is off.
And so that's where that this pin right
here is mounting on your pedal. That
might need to be go up or down. Okay?
You might have your pedal ratio off for
your application. So make sure that you
have that set up correctly. Um there's a
lot of great tutorial videos up there on
understanding pedal ratio, whether you
need a 5, six, or 7 to1 pedal ratio.
Generally a five to six pedal ratio is
usually what you're after. Unless you're
running manual brakes, maybe a 15/16
master cylinder, then you want a higher
pedal ratio. You're going to need more
leverage. But when you got a brake
booster, you do not need as much
leverage. Okay? If you're converting
from manual to power brakes, you might
need to lower that pin down and get to
where you don't have as much pedal
ratio. So, little tips and tricks,
things to remember, but uh you're going
to want to make sure that you you set it
all up correctly. So, great product
here. Again, this these brackets here
are designed specifically for trucks
that are lowered where we got to get a
little bit tighter application cuz that
motors come up and we got to get that
booster in a little bit different spot.
So, we have another kit that we use at
these brackets a little bit bigger that
run with an 8 in uh brake booster. So,
hopefully this is helpful. Hopefully
this explains it why we have two
different kits. What might seem like the
same application and it is strictly just
ride height, motor placement. when when
it's low, suspension comes up, engine
comes up, and we have to move things
around a little bit. So, a great
product. Willwood makes a great product.
They've really stood behind us and
helped us out. Yeah. Are they perfect?
Is it is all this stuff, you know,
perfect? No. I mean, I buy a brand new
truck and I'm taking it in, you know, 3
weeks later cuz I got issues, right? And
we we've heard about all the GM recalls,
the Dodge recalls, the Ford recalls.
These guys are spending millions and
millions of dollar in R&D and still
things don't always work out like you
hope. So, but be patient with us. If you
have any questions, please give us a
call. Oh, one last thing I want to
mention right here. This is really
important. A lot of guys struggle with
bleeding the master cylinder. They give
you these little tubes right here where
you and they teach you about bench
bleeding your master cylinder to make
sure that this is working correctly. It
makes a big difference to bleed this get
all the air out of this. Then when you
connect it, you're really just trying to
push the air out of your lines and and
clean all that out, right? So, make sure
you bleed your brakes. Bleed your
brakes. Bleed your brakes. The
oldfashioned way works good. Just have
somebody in it. Pump, pump, pump, hold,
crack it, get it all, get all the air
out until everything's good. So, please
make sure that you bench bench bleed
your brakes and uh ahead of time, your
master cylinder ahead of time. So, great
product. Hopefully, this is helpful tips
and tricks for you and this explains the
kit a little bit better for the lower
truck. So, like, subscribe, always, and
uh keep us posted, you know, let us know
how it goes and uh we'll see you next
time. Happy hot rodding.