Spiritus Systems: LV-119 Plate Carrier

Ballistic Lab
1 follower
1 Video View·Jan 6, 2026
Spiritus Systems: LV-119 Plate Carrier
Hey guys, tonight we're going to talk about the LV119 from Spiritus Systems.
It's their plate carrier. It's been out for a while now.
Started out with the Covert model and then they transitioned, I believe, to Overt only fronts.
You can still get the Covert rears or the Overt rears.
And then they recently pushed out a batch of their Over the Beach,
which incorporates a lot of mesh to it.
If perhaps you haven't looked at one of these because you were waiting on the Over the Beach
model, this will give you kind of the intro to it and then you can look for the finer points
on the differences. But we'll get this on the table and run through it.
It's a unique plate carrier. It's got some interesting things going on on it.
Plus it hosts the Spiritus back panels, which are
arguably the best back panels out there right now.
So let's go down the table and take a look at it.
All right, so before we get too far into this thing,
I do want to swap out these plates so it's a little bit easier to manage on the table.
But right now I've got medium eSappies and backers in here and it is a medium LV119.
Some people recently have given me a hard time about using eSappies and backers as the baseline
because they're not the most common plate out there.
I don't think that eSappies are really rare in the commercial market anymore.
But it's also like a known standard, all right?
I could throw up, you know, whatever HESCO, Hoplite, RMA, any other plate, right?
And unless you have that plate, it's kind of not the most easy to use.
But the eSappies are set to a pretty rigid sizing standard.
So you can easily measure that out and see how it compares to your plates versus some
random oddball plate.
All right, so additionally with it being marketed as a, you know, duty quality plate carrier,
I just wanted to show it with duty plates in it and see how they fit.
So this is not uncommon these days to have, you know, a little bit of plate,
a little bit of backers sticking out the bottom.
The Velcro lines up pretty well and I probably could have muscled that in there just a little
bit further.
So it does fit, you know, medium eSappies and backers in their medium, which is kind
of what I would expect from a plate carrier.
So with that out of the way, we'll get these plates out of here and run through some of
the features, right?
Now that we've got plates out of the way and we don't need to deal with that obnoxiousness,
let's start on the front plate bags here.
All right, so one of the kind of main, most notable points about the LV119 compared to
other plate carriers is the rather straight shoulder straps, all right?
That's really a take it or leave it kind of thing, all right?
You either enjoy the angle that comes off of the cry plate carriers or you like the
straight shoulder straps on the Spiribus.
And it's really no slight on either side, right?
Like whichever one works for you, works for you.
And I'm glad that there's options out there for people.
That said, I do not prefer the straight straps, all right?
I have heard people say that the cry ones are too extreme and that's possible.
I haven't, you know, done the angles compared to other things on the market.
I kind of look at it as either straight or angled.
And the angled ones tend to fit me better, all right?
That said, it's not uncomfortable, but you may or may not feel it on your neck and your
shoulders a little bit more than you would something with an angled shoulder strap, all
right?
Looking at the front plate bags here, so you've got Velcro, lower field to engage with placards,
which really molly down here these days is pretty uncommon, especially if it's also set
up to use placards, all right?
So your side release buckles just kind of hang out on these straps here, which are hidden.
That's kind of nice.
It keeps everything a little bit more low profile and snag free.
If you don't need those buckles, you can absolutely take them off and then, you know,
just run an insert there or have it slick or whatever you want to do.
Looking at the top, you've got two rows, yep, because this is just Velcro sewn here,
two rows of usable molly, four columns, so it fits your end user devices or smaller admin
pouches just fine.
And then you've got some webbing coming off of the sides there for push-to-talk mounting
and what have you, all right?
I do believe this is a solid pass-through here.
Maybe.
I could have sworn it was a pass-through.
It goes somewhere.
Where does that terminate?
Perhaps it's not, or maybe I'm just being dumb and missing it here.
I'm not sure.
Nope, I don't know.
So comms routing, you can tuck comms in there, comms wires.
It appears they have nowhere to go, though.
I thought that went straight through.
Somebody can correct me in the comments if they want.
You know, I'm under pressure on the camera.
All right, so that's kind of the front plate that I got to nut shell.
You've got these two chunks of webbing coming off here, which I thought engaged with tubes,
but the spacing doesn't look right there, so I'm not quite sure what's going on.
That may just be for strength on the plate body, plate bag body itself.
I'm sure somebody will call me out and let me know that I'm stupid if I'm wrong on that,
though, all right?
Looking at the interior face of the plate bags,
the front plate bag has this big stretch pocket here,
which is kind of a tweave-type material, if not tweave itself.
You also have that running the length of the sides of the plate bag.
So, you know, you can fit whatever you want in there.
Maybe one of those Focus, I think that's how it's said, Focus IFAK kits, the plate bag IFAKs,
that might fit in there.
You put, you know, some SSE-type stuff in there.
I've heard of folks carrying blood bags in there, not full blood bags, but blood bags.
Nonetheless, signal panels, kind of whatever you want.
I don't find it overly accessible for me, so it's really kind of a take-it-or-leave-it feature for
me, but it's there, and if it makes sense to you, run with it, because why not, right?
The Velcro orientation on the plate bags, you've got the hook coming off the front pocket there
to secure to the loop on the body side.
So, trying to do that, make note of that for dangler compatibility.
I don't know which danglers necessarily have that,
but that's the orientation that you need to worry about.
All right, so it's a pretty drama-free front plate bag, right?
Look at the shoulder straps here.
Try to get this out of the way.
It is, you know, two layers.
You've got your rear straps coming off the back, which is hook facing down,
and then loop coming off the front bag facing up.
So, this will marry with your cryoplate bags.
So, for whatever reason, you want to use JPC front and Spiritus back,
or Spiritus front, JPC back, you can do that.
They're not going to line up perfectly well angle-wise, but they will line up,
and then you can kind of clean that up with the shoulder strap sleeves there.
So, that will work out.
Okay, and then looking at the rear plate bag here,
the rear plate bag is kind of where my opinion on this thing may differ from a lot of people.
So, before the back panels were available, I made no effort to get a 119, right?
I'm not a fan of this back plate bag as it sits,
especially without all of the needed support.
So, we all knew it was coming, right?
Because it had zippers on it, and the back panels were going to come eventually.
But before we got to that point, it's really a fairly useless back plate bag.
You've got this one row of MOLLE webbing about midway, and then a row across the top
that you could use to potentially mount something, but not anything very well.
If you put a hydration pouch on there, you'd only have it mounted in two spots,
so it could sag in the middle here, and then it could flop on the bottom, which wasn't ideal.
If you go back, I've got a video on how to mount a Hayley flat pack on here,
and that needed some kind of arts and crafts as well to make it work.
So, before the back panels came out, there really was no selling point to this thing for me.
Now that they're out, the back plate bag has a lot more utility,
because I do like the Spiritus back panels quite a bit.
I think they're very well done, and one of the stronger options out there.
That was compounded by the cummerbund mounting, which I absolutely despise.
I hate it. It works, and it's totally functional.
I just don't enjoy working with it, and it was icing on the cake to not get one.
So, we can kind of see it looking in the plate pocket here.
You've got this grid that's in here with a bunch of holes cut in it,
laser cut holes, which are for shock cord routing,
and then you've got pass-throughs under the zipper that then go into the rear plate bag right here.
What would happen is you'd have to feed the ends of your cummerbund in,
and then route it and kind of secure it to this grid, all of which is being done inside the plate
bag. You really can't do it with the rear plate in there, so sizing was a multi-step process.
You had to push your cummerbund in and then put your rear plate bag in, throw the thing on,
try to figure out how much slack you needed without pulling out too much,
and then come back, take the plate out, and then try to secure it in the same spot.
All right, so I will say the routing on the stock Spiritus cummerbund
was a little bit cleaner than on a JPC-style cummerbund, so you've got the, at least on the
elastic ones, the skeletal cut Spiritus one is kind of the same thing as a Cry, but so you just
had the three routing loops and you didn't need to really weave as much. You just kind of got this
where you wanted it and then tied it in place, versus with the skeletal where you've got to use
the MOLLE and really make sure you've got the slack taken out where you want it to.
This is not one of their MOLLE cummerbunds. I've got one of their skeletal cummerbunds right here
for a different one that I'm putting together, but you can see it is, you know,
skeletal cummerbund all the way across, and it's going to be the same pane as weaving a Cry
cummerbund in there. This one is actually one of the ANA Tactical CQ cummerbunds, so
that, I'm not a fan of that. There's been fixes put out, so Axel just put out a
panel that you could make work. You can tie it in there and then route your skeletal cummerbund
and kind of tie it. I don't know, there's different adapters that make it
less of a pain to work with, but I do not enjoy that, and I'm really beating that to death, but
it was a thing and it's still a thing. And then the rest of the rear plate bag is pretty uneventful.
So you've got this hole here, which, I don't know, drainage, potentially running
shock cord out of. I'm not really sure what the idea there is. Let's see if we can try to
run down this routing here. So these plate bags are a straight pass through
all the way into the plate bag, so if you need to run comms cables through there or something,
you could run it down your shoulder strap and then come out over by your cummerbund if you
needed to, so you can mount an antenna or something like that. I'm really wondering
where this front plate bag routing goes. I don't like leaving you guys hanging.
Yep, that really doesn't connect there. So the top strap here just comes into the plate bag,
and then this doesn't go anywhere. Man, I really thought there was something else to that.
Sorry guys, letting you down. All right, but that's kind of the 119. I probably talked too
long because there's not too much to talk to you about on the LV119. You've got the two different
cummerbund options, the elastic celled with this rear mounting, and then the spirited skeletal
cummerbund. So I've tried this one out a little bit. I'm not a huge fan of pure elastic. It just
limits too many options. And then we've got the skeletal that I'm going to try out. I didn't
realize the skeletal was reinforced. They do have some stiffeners in there, so that's a positive
win on that. And we'll see how that plays on a different plate carrier that I'm putting together.
But there you go. There's the Spiritus LV119. Got a new gray plate carrier to replace this one,
and I got a donor rear bag, which is the part that I care about. So this thing will go up for
sale. Nothing wrong with it, but it just wasn't quite my cup of tea. So thanks guys. Appreciate
your time.
