FREEING THE SPINDLE! - Victorian Radial Drilling Machine Restoration PART 5

Screw Driver
87 followers
#machinery #motorbikes #occupations #career
This time on the Victorian radial drill restoration project I take on the drilling head and begin to free off and remove as much of the parts as possible. The spindle/quill assembly still needs extra work but we are extremely close to having the entire drill completely stripped down - Hope you enjoy the update!
We are another step closer to having this old machine drill some holes!
Instagram - / iron_jonsey
It's time to take on the drilling head, the cutting edge, the business end,
where the magic happens, whatever you want to call it,
this is one of the most complicated assemblies on the machine.
We have feed screws, gears, bearings, shafts, spindles and quills,
all locked together with 50 years of rust and grime,
so let's see if we can get any of it moving.
The drilling head slides up and down the arm and we last saw it back in part one,
when I cut the drive shaft it slides on and lifted it from the arm.
It's been sat to the side ever since while I focused on the big bits.
So before I try and free any of this off and get some parts off,
I'm just going to go over exactly what's going on here,
what I know and what I don't know.
So the power from the column comes through here,
this is the shaft that I had to cut to get this off the arm,
is the shaft that the whole thing slides up and down on.
This is keyed to a gear here which then drive this gear here,
which I've already removed from this shaft,
that then drives this set of bevels which is keyed to the spindle,
which is this piece and obviously down to the drill.
So the spindle comes through this bevel,
I presume it's keyed to it, it must be,
and end float is taken up with these pair of locking collars.
So this is the top of the spindle,
this screw thread is the means by which feed is applied,
that is driven through this shaft here which we've already removed
and at the top of that shaft is this gear which drives this gear.
This gear is keyed to that screw,
the internal nut for the screw is this thing held captive in the casting,
so when this gear turns it drives the screw which forces it down,
pushing on the spindle and applying feed to the drill.
I'm 90% certain that this screw is hollow
and the spindle extends up all the way to this cap area
and this nut and screw here is an end float adjustment
and is bearing down on the top of that spindle.
So when the screw is reversed it pushes up this way,
pushes on the top of that cap and then the spindle can be retracted.
My first plan of attack is to try and remove that cap,
I'm pretty sure this is threaded on and then we can see for certain if this screw is hollow.
Oh early victory, what's under there?
Not much, we found a little pin here,
I think this is the top of the spindle and this is the top of the thread,
so there's a seam there I believe, let's knock this pin out and see what happens.
I just smacked the camera, that was clever.
It's going though, oh there it is and in theory that will come off.
Does it unscrew or what?
Let's get these on it and see, there we are.
Right that makes sense, that is the top of our spindle,
so that is pinned to there and then that is obviously threaded down onto the screw
and then this screw comes in the top of this housing
and bears down on the top of that and that's a bearing surface
and then this oil hole comes in, fills this point,
allows some to dribble down the side and then lubricate these two surfaces.
Huh well that's interesting and if I'm extremely lucky this might wind out.
No not yet anyway.
I didn't realise at this point I was making a pretty daft mistake which you may have already
noticed but I proceeded to lift up the head and bolt it to the machine freeing off table.
More weight, turns out Muggins here was turning it the wrong direction,
it's actually a left-hand thread but yeah look at this
and even better the nut is staying stationary in that casting
so it's the screw that's coming out which is incredible.
Oh wow, now I'm not worried about marring up the surface of this with the jaws
because this is so pitted I decided a long time ago that I'd be making a new one of these
so I just want to get it out so the gear can be rescued.
Oh yes there's some crud in there, what a beauty!
One piece at a time and then cast me down.
There she goes, let's take this to the vice and see if we can get this gear off this screw.
What I didn't realise was that the nut was in two pieces and that the top part of it had come
out with the screw and gear. After the screw wouldn't move through the gear at first I
realised it wasn't part of the gear and began to unscrew it. It put up a bit of a fight and
I did cause some damage, thankfully nothing that isn't relatively easy to repair.
With the screw out and its drive gear safe it's time to get the quill and spindle assembly moving.
Because it's still locked to the drive shaft by the bevel gears I need to work carefully to free
them both at the same time. I start with the drive shaft end and see if I can get any movement there.
There's a smudge of movement. So this shaft here which is the one that drives the spindle through
these bevels is moving backwards and forwards as much as the backlash on these gears will allow.
So that is promising, what is not moving is the spindle. What I don't want to do is just use those
gears as a lever to get this moving via that shaft because they'll just go ping and I don't want to
do any dentistry work on them. What I also don't want to do is use my pipe wrench on the spindle
because I don't want to chew it up. I don't mind chewing that up, that's easy to repair, the spindle
is a lot harder to repair. So I need to come up with a different way of getting some leverage
on this spindle which means it is time to make a special tool. The next morning I was able to
apply some serious leverage to the spindle but unfortunately it just slipped. But the theory
was there so I pumped some heat into the casting and put a few extra turns on the tool clamp and
tried again. So it's going, a bit of forbidden fluid to help things move along. There's a sloppy key in that gear
that's gonna need changing. Woo! Gotta love a homemade tool, another successful one.
Now this wants to come out, I'll just work it bows and forwards.
How's that supposed to come off? Another bevel gear free, blimey!
Now how does the spindle come off? I'm not entirely sure. Right I've just cleaned up this
area and now I think I've got a pretty good idea of how this went together and how it is
going to come apart. So this piece here is the quill and you can see there's a great big key
there which is in line with the keyway in the spindle. This piece is also quill and this drive
gear is keyed to it. You can just see hiding in there is a keyway. These locking nuts come down
and then you can use those to adjust end float in this bearing. We've got bronze bearing, we've got
one in there and then obviously this one here. So the spindle extends all the way through the quill
and then comes out the top. This is the spindle here, there's a bit of wear on that. This is where
our screw was so that's the screw that pushes down on the top of the spindle pushing it through the
quill and then also pushes back up again onto this locking nut assembly here which retracts
the spindle. So in theory the spindle should just drive out there right through the quill,
in practice that is a little bit more tricky. I don't just want to go ahead and belt like hell
on the end of that because it will ruin it. So what I'm going to do is this piece of scaff
conveniently fits in there, goes through the threaded portion and into the quill and then
stops up against what I assume is the shoulder on the spindle. The shoulder where it stops being
that thin diameter and starts being this diameter. The whole quill's moving so that's fine if it
wants to do that. There she goes. That key's got to come out. That is heavy.
So this shaft is for traversing the head along the arm. The ugliness on the end is the remains
of a fabricated handle that was once there. The original is long gone and probably smashed
and a replacement will need to be cast. On the back side is the pinion that engages with the
rack we removed in part three. I think that comes out from the other side. Yeah it's loose look.
So get this flipped over, see if we can get that out. So this drive shaft and gear at the back of
the head is the shaft that we had to cut out. This shaft drives this gear and then the head can slide
up and down this shaft. So this gear has got a long extended hub on it and it rotates inside this
bearing and the shaft slides through it. The shaft is moving backwards and forwards but I cannot get this
gear and hub to rotate in this casting. I think it just it just needs more heat and oil and patience
so we're gonna have to give that another go next time.
