MASTERING The Art Of BIG DENT REPAIR: Expert Tips And Tricks | NO Paint

Auto Retech
2 followers
Oops I love that sound Hello
I'm back again Martin Saddle here with
Dent Remover and I've got another
beautiful dent repair for you guys
And this time it's on an Audi A1
Lovely color no nice dent
I'm going to show you guys how I fix this
Using paintless dent removal techniques
from start to finish Show you as much
detail as possible and I really hope you
enjoy this repair So grab a brew and enjoy
I'm getting straight into this repair but
first I need to get behind the panel To do
this I'm removing the wheel arch liner
Simple enough to do just a few torque screws
And then pull it out that way
And as you can see inside the
panel the dent is easily accessible
And this looks like a complicated dent to fix I'd say half of the
panel is damaged or deformed with
multiple body line areas affected
And the gap between the bonnet and the wing has also closed up
The edge of the panel on the arch has been pushed in completely
And I'm very surprised that the paintwork hasn't been damaged
This top body line dent is holding
a lot of tension and the bottom
body line looks very crumpled and does not look fun to fix at all
There are so many ways to start a repair
like this and lots that could go wrong
as well So I need to pick the correct
tool to start this repair and succeed
I'm going to start off using the dodar tool and I'm going to
put a large rubber screw tip on
the end like that you can see it
And I need to get a bit of heat in
the panel as well so everything works
a little bit better when it's warm All right so a bit nice and warm
So I'm going to start off at this point here and
just carefully ease it out
using the tyre as leverage
So I'm going to hold the bottom
of the panel while I press
my finger just right onto
that spot and then wish me luck
Oops I love that sound
Go all the way to the top as well up there
So I'm really happy with how that's turned out I did think quite
a lot of it would just pop out
I am left with quite a lot of areas
So this bit here needs to be tapped down
There's a lot of tension in this area
and there's no way I can pull this body
line out without tapping that bit down
Tap this bit down and do a bit of
tapping and pulling But there you
go good innit I need a wide flat nose knockdown and hammer for this
And then the panel needs to be heated up
with a heat gun to get the panel all nice
and warm to help the metal move I'm choosing the most prominent high areas first
Trying to level the buckles and
ridges so that I can read the damage a
bit better on my reflection board So
I've tapped a few of the crowns down
It's starting to sound a bit springy so that suggests it might
pop back up a bit So I need to
start pulling out the low areas now
So I've moved on to the fender pliers okay Version three
fender pliers with a screw tip
on them if you can see that
So screw this onto the tool and then
basically it's just like a set of
pliers Just start nibbling away like
that Popping it onto the panel like that
Find out where the tip screw tip is and
then just very carefully ease that dent out
This is a very steady process and I need
to be accurate with every push from behind
I can see the pushes I'm making with the fender pliers by
looking through where the U-bend is cut
out between the two feet
Once I've leveled up the area I need to
use the knockdown to tap around the low areas some more This lowers the high
parts and reduces the
tension in the panel
which helps me lift more low
areas up with the fender pliers
Going back in with the fender pliers I took off this
green tip screw tip and I'
m putting on a soft cap tip
It's similar but this one is just a bit sharper at the end
When I say sharper I mean that by using this screw tip
It lifts the dents up with a bit
more precision This also applies
to the two knockdowns as well as the ends are a smaller diameter
It was more severe than the first knockdown I used on this repair
So this area I'm pointing to
is a sharp high point holding
lots of tension and this is gonna get lots of hammering
This part is in fast
motion so you can see
the amount of knocking down that's needed
to fix a small area And that's me in real time at the top corner at normal speed
So much work this little crease needs
to be flattened down And after all that hammering I now have an uncomplicated
low area This is much easier to lift up
Whereas I'd have really struggled before
And for this I'm gonna take off
this screw tip and pop on a sharper screw tip
So I'm going from blunt to sharp
That's the way I do it
You can see that
Okay plastic sharp tip
Just adjust these feet
And I also need to get a bit of warmth
in this panel as well because it's gone cold
And then straight back in Using
a plastic tip instead of a steel
one reduces the chances of over
-pushing and damaging the paint
Also as I'm now working on the body
line area my pushes have to be very
accurate and I need the small surface area
of the tip to do the work for me
A blunt tip would require more power
from the pliers to get the same effect
So matching the pushing tip with the
knockdown the sharp and plastic one
This is accurate and safe for the painted surface
All that work has made the body line look much better
Now the line is leveled up
I need to go back in and lift the lower areas again
The tools I'm using for this part are the moose knuckle and
then the double bend screw tip
And I've got a rubber tip on there
Okay this is going to
push a lot of metal out
without really deforming the painted surface the
panel putting any kind of pick
marks in there anything like that Pop it in like that
Straight onto the back of the damage And
there we go I've got my thumb
on the panel lip to support it There 's
lots of push power from this bar
Due to my leverage point which is about 80 to 20
Now that those low areas
are up I can go back
in with a blunt nose knockdown and tap down those high areas
And then going from the rubber tip
back onto the plastic soft cap I'm
fixing the diagonal crease which is
made visible using the line reflection
The lines spread out and zigzag to indicate the low area
I have highlighted this area
so you can see it being repaired
When I'm pushing this crease out I'm trying
to work the damage out
by carefully massaging
it from top to bottom and then bottom upwards
This lifts up the metal nice and evenly
Once that's done I'm moving back a
little bit fixing two more low areas This
one still has prominent crowns but I 'll
be able to sort these in a minute
This last one doesn't require much work but I've fast
forwarded the clip so you can
see it come out a lot better
Okay more knockdown work A few high
areas here because
the lines are getting
closer together Tap these bits down
and again keep going in with the bar
Lots and lots of knockdown work there and
it has made this panel look great from
this angle But it's always best to repair
dents from multiple angles if possible
This eliminates any hidden pockets of damage
as we dent technicians use a reflection
source to project for lines or fog shade
onto the panel So what looks great one way
It will almost certainly look wavy or rippled from another
This is going really well but I am struggling a little bit on
this area here Okay it sounds a
bit stingy kind of stretched almost
And that's because of this area here So that's still holding a
lot of tension So I need to tap
it down pull it out a little bit
Because that's in it's making this really tense
So once this comes out it's going to relax the panel
So I just need to leave this area for a little while
And go on to
that one Same as always there's plenty of heat in this panel
which makes it move a lot easier
And then we get the door dial in there
This orange tool is so powerful as
you saw at the beginning of the video
reaching right up behind the panel
And onto that top body line trying to lift the dent up
But that top crown is holding back so much locked-in tension
the panel has no choice but to spring back down
Next I need to tap it down with the flat nose knocking it down So by tapping above the
body line directly onto the crown reshaping
this area will push that tight metal downwards
where it used to be
And at the same time stabilize the panel lower down
If you look closely you'll see the panel vibrating
and that's showing that the panel's reacting
To the work above
And then I'm gonna swap this tip
and put the plastic soft cap on there
And get right onto that body line
as well Just look at the difference
already It's looking a lot better now that the crown has been fixed
And below the body line there are a few
high areas left that need to be leveled up
This area is coming on really
well but I'm just struggling a
little bit with leverage up there
So I have had a look underneath
And I can get to it by lifting the hood up
So it's always best to check all these things
Sometimes you just forget
But yeah the hood's gonna go up
And I'm going to get right to that dent
Two holes and super access But I need to
protect the inner wing so I'm going to use
one of my ramp rubber pads to lever it off
Let's try this then There you go On with a plastic bullet tip Sliding my
bar through the top of
the wing and finishing
off the top part where the crown was
All that's left here is a few micro low and high areas
The highs I'll fix in a few seconds
And then moving below the body line
I'll finish off this shallow low
The panel feels very springy when I push it
And that seems to be a good sign
that I'm strengthening this area
Using yet another sharp
knockdown to finish off those
small micro highs And this part is pretty much there
Okay it's looking really
good Now that I've done
the top part I've got it about 99% something like that
There's just a tiny bit of finishing
off to do But I've also got
quite a few crown or ripples up here So I'm gonna knock those down as well
Again knocking these down is gonna
release all the tension and just help me
finish off this wing But yeah it's looking
all right It's a bit rough around here
But I'm winning and that's the main thing
Those crowns have been compressed
So now I'm going to move to this panel edge right here
See where it's bent there
Okay so a little time spent on that
Again this is going to give the panel some strength
So everything I'm doing is just to add strength
to these flat areas
And you can see there's still
a bit of tension there But
once those get knocked down this should tighten up a little bit
So the best way to repair this edge
this lip is using some Swan Neck pliers
Okay so these go onto the lip like that
And then I can just carefully bend it
And reshape the edge This will take the
pressure off that and it'll ease itself
back in But I need to warm it up at the
same time So get the
heat gun on there first
and then I'll show you how I do it
These pliers are also known as
goose neck pliers and are an amazing
tool for both PDR and
body shop technicians They fit under the arch
Even when the gap between the tires is tight
If we take another look
So this is just from bending that lip straight
There you go look it's just about repaired itself
just a tiny bit there
So I'm going to put the light board on there and give
it a few knocks
with the flat nose Knock down
And that's the edge done So while
I'm on a roll finishing all the
outer areas I'm going to move
towards the front So let's have a look
Got this part here
There we go I'm gonna knock
that bit down and just address the low areas And there you can see
it just there right
where the lamp is
Gonna maybe go through the top
as well just to see what's best
with fixing that So once
these two bits are done I think to be fair
That is the majority of the areas done
And then it's just this bit in the middle
which you can obviously see So yeah
that top has come out quite nice as well
Just a bit low there
So yeah coming on very well
So I've just put this bar in
there through the arch liner and I can get right onto the edge of the panel where that
headlight is I have
to be careful with this
but yeah let's take a look
Very good so far So I'm
just gonna walk this dent out
now This panel edge is very flexible as you can see
So a lot of care needs to be taken near
the edge Too much
pressure from the bar and the edge could
blow out Another way to fix this would be to remove the headlight
And use fender pliers to limit panel blowout
Repairing these dents also pulls the top of the
panel out and realigns the panel gap to the bonnet
And that's the front edge done
So now that the outer areas have been
repaired I'm going to go back into the center
of the panel where it's still quite ripply
Another area which needs straightening
It is the panel edge and below the
body line So much tapping and pushing
trying to bring these
areas up as neatly as
possible which is quite a big task
This is why I've time-
lapsed this part because
there's so much swapping between hammers
and bars the unfolding repair was quite hard to
see at a normal speed And to be honest
The area above the body line seemed to be work-hardening
and this was giving me a bit of hassle to straighten it out
Okay so I've spent about 20 minutes on this area just did a bit
of a time-lapse because it is
quite steady to watch this process
Watch the dents and ripples come out but it'
s looking pretty good
Let's have another look
So this top bit this is what I'm talking about around here
Okay it's quite weak as you can
hear so I'm guessing it's this
part here So this is
the area I'm going to fix now right on the edge
For the edge I'm going to be using this
tool It's really good for getting right in
the bottom edge of there And then I
can start pulling the dents out like this
But can you hear that That is
the stretched metal moving popping in and out pop So
that tells me that
this area definitely needs fixing
To strengthen that area
It should stop popping in a
minute once this dent comes out
There you go
It's amazing you know when
you just think a dent goes in
there and a dent can
pop out but there's all these little
areas these little pockets of tension
You need to find all these areas in
order to successfully repair the dent
This is a great little tool for edge
work I also use a J or a hook bar
and once it's hooked underneath the
lip both tools are highly effective for
getting right into
the inside edge but
as with all these tools care has to be taken
And it's always a good idea to tape
up the tips so that it
reduces any mis-pushes or very sharp picks which can damage the painted surface
Slow is fast when it comes to fixing panel edges
Okay this edge looks pretty
good now It took quite a while
to do but I'm happy with it
so let's take another look
I'll just turn this around so I can see as well
There you go that's the edge
So now I'm working on this top part
I've spent a bit more time on it
off camera just trying to sort it
out but there is a bit of a low there
Which is quite fragile as well
So the part that was popping in and out earlier
that's still a bit of an issue
So yeah I am getting there
It just needs a little more time
on there to fine-tune it with very
sharp picks So what I have been using is that one if you can see it
That's a very sharp tip and I can
pick in between the orange peel
and at the same time shrink this
area So I'll keep plodding along
But I'm nearly there now A repair like
this can take a day or more to complete and
also to produce a high-quality finish
This type of paintless repair is not cheap
and often matches the price of
a conventional repair and paint
So by using this repair method it won't
devalue your vehicle
because we magic the dents
out Also by not painting the vehicle the
manufacturer's paint warranty is not affected
And the repairs are
completed in less time than a
repair and paint One other thing there's no dust
I'm so close now but I'm chasing
perfection The body line has had a lot of
work done to it So many push and tap
marks have bitten into the painted surface
dulling the lacquer and not giving me a clear reflection from the board
So the only way to fix this
It is to use some 2000-grit sanding paper and a quick polish
That was a very very very light nib and polish
I just wanted to get the reflection
back into the panel so I could read the board
And now I can see that it's just slightly
high So I'm going to use my black knockdown
I have been using a very sharp
one like that but it's just
been biting into the paint a little bit So off we go again
And now that's tapped down I need to lift a little bit more up on this
body line Very fine tweaks now focusing
and tapping down the nipped lines
ghlighted by the reflection board This panel
is so strong now It has the strength and
rigidity of an undamaged panel And it's so
satisfying to see this stage of the repair
It looked like that 20 minutes
ago And there you go That is the Audi A1 front wing completely
finished Well not completely finished
Because I need to give the panel a
polish up and then refit the arch liner
But there you go And that's how you fix it with paintless dent removal
I'm Martyn Saddle from Dent
Remover Thank you so much for
watching until the end I really
appreciate it See
you later Cheers
