How To Clean Clock Parts In An Ultrasonc Cleaner

Chrono Chronicles
8 followers
4 Video Views·Dec 21, 2025
Welcome back to another Scotties Clock World clock repair tutorial.
This video was requested by a Subscriber.
It shows the complete process from disassembly of the clock movement till the parts are returned cleaned to the work bench.
There is more information in this video than I usually include in my regular videos.
Hi, I'm Scotty. If you want to learn how to service and repair antique mechanical clocks,
then subscribe to my channel. Welcome to Scotty's Clock World.
The ultrasonic cleaner has been preheated to 30 degrees. On the left hand side of the screen
there down the bottom you can see the mixture that I use in my ultrasonic cleaner. Now we're
ready to start putting the parts in. First I'll start off, I'll cut a piece of wire,
thin piece of wire, so we can tie the parts together for two reasons. One, it makes it easier
when we're taking the parts out for reassembly. We know what parts are from the going side train
and what parts are from the strike side train. And also it stops the smaller pieces dropping
out of the bottom of the mesh cage in the ultrasonic cleaner. There the first three
wheels put on for the going side train plus the escape wheel. I'll tie them up now so that they
stay in place and don't fall apart. This video has been requested by a subscriber who wanted to know
how to clean clock parts in an ultrasonic cleaner in a bit more depth than I usually put on my
videos. Well that's the going side train done. Now we'll repeat the operation for the strike side.
Cut another piece of wire, bend it over. The wire is pretty thin that's why I bend it over to make
it a little bit stronger. Twist the end so it doesn't come apart. Okay now we put the parts on.
First wheel, oops fell out, try it again. First wheel, the second wheel, it's also called the
maintenance cam. The third wheel which is a warning wheel, has those two little pins on it
and the fly. Put them together, jiggle them down a bit, tighten them up. That'll hold them together
while they're being cleaned. A bit of excess wire there, I'll cut that off and that's the
strike side ready to roll. Put him aside. Now I'll take the mesh basket out of the ultrasonic cleaner
and we'll start to fill it up with parts. We'll start off with the back plate, put that in
and then the front plate because they're quite large, quite wide. So we need to make sure that
they're down below the second level on the side of the mesh basket which I'll point out now.
That level there so that they're all fully immersed in the cleaning fluid. If part of the
plate sticks up above that you'll end up with a line that hasn't been cleaned in it and then when
you re-clean it the rest has been done twice so you won't get rid of it. Clock wheels have now
gone in. Now we'll use these little mesh containers. They're actually tea strainers.
Now this piece here is the motion works, we'll put that in next. Now back to our tea strainers again.
They're very handy for putting small parts in so they don't fall out the bottom of the mesh basket.
Under the clip, open it up, put our fast slow adjustment in, put it aside.
The nuts don't go in because they're steel. In a smaller basket I'll put the clip that holds
the count wheel on and also the four nuts that hold the plates together. Right we'll close that
up now. Put both the tea strainers with their parts in them into the basket now and see what
else we've got. Right we want the great wheel and the winding arbor from the going side and the
strike side mainsprings. We'll remove the great wheels. I might have to use a multi-key on that
I think. Wind it backwards so it unwinds it from the whole end and it just comes straight out.
That's the mainspring all clamped up. Lots of oil on this, seriously over oiled. We'll
clean that off with a fresh cloth before we put it in the ultrasonic cleaner.
Give it a bit better chance to clean it up. Now we'll do the same with the strike side.
It's no doubt just as oily but we're going to find out. Multi-key on it, wind it backwards.
You hear it click out. Mainspring back into the box. That's a loop end mainspring.
That's different from a hole end which we have in other videos I've done. You can see the grease on
that. We'll wipe that off again. This is a pendulum. We'll put the pendulum in. It's all brass that can
go in. That's not a problem because both the great wheels look very similar. We want to put the
correct one back in the correct side. On the strike side I'll put a little bit of wire.
Wind it round just so that when it comes out we know that it's from the strike side.
Twist it round. There it is. That's a piece of wire. We'll remember that.
Right now we're ready to put the basket into the ultrasonic cleaner. In it goes. Remove the tub
for a minute. Turn it on. 30 degrees. It's reached temperature. We'll put it on for five minutes
and we'll let it run. The ultrasonic cleaner is now finished.
So we'll take the basket with all the clock parts in out of the top. Put it on a tray.
There are the parts. You can see they look a lot cleaner than when they went in.
We're now going to head out to the kitchen and go through the next part of the process.
We're in the kitchen now. We're going to clean the ultrasonic cleaning fluid
off the clock parts. First up we'll fill a tub with cold water and then remove
the parts from the basket and put them into the into the cold water.
Tea strainer first. Got the tea strainer. That's both the great wheels. The going side
and strike side. Pendulum and the back plate. Now the front plate. Now the strike side
wheels going in. By the going side train wheels. And last but not least the count wheel.
Put a little bit more water in. Wash the parts. Got some of the early
ultrasonic cleaner fluid off it. Put up with water again. Now over to the other bowl of the sink.
We've got some warm water we're putting in there. We're going to transfer the parts from the cold
water over to the warm water. Turn the tap off. Going side wheels. Strike side wheels.
Both the giant wheels or great wheels. Count wheel. Back plate coming up next.
Just fits in. Motion works. The other half of it. And last but not least the pendulum.
Okay once again shake them round. Agitate them. We want to get as much of the ultrasonic cleaner
fluid off it as we can. Now we're ready to set up the next part of the operation. We're using
shellite also known as lighter fluid which is pretty dangerous so be careful when you're using
it. We'll tip it into another tub and what we're going to do now is take the individual pieces
out of the warm water. Shake some of the water off them
and then put them into the shellite. Once I've been there for a little while and we've moved
them round we think we've got most of the water off them. We'll take them off. Put them on our
clean cloth outside there and we'll put a heat gun over them on low speed in a moment to finish
the operation. In the meantime we're taking the the wheels out putting them into the shellite
and then once we've shaken them round taking them out of the shellite putting them onto our
clean cloth where they can dry out a little bit. Some of the shellite will evaporate off
at room temperature. We'll remove the rest with the heat gun in a moment.
Back to the hot water or the warm water container.
Take more parts out. Put them into the shellite. Get them round. Get rid of the water contained
on them and in them and the front plate. Quick shake. Lift some water in the shellite off them.
Put them onto our clean cloth. Motion works and the pendulum bob and the front plate.
Right now we'll put the shellite back into its container. As I said before it's rather dangerous
so we'll put that away. Pour it in through the funnel. Then we'll have a look and see how much
water this shellite has taken off the parts. It collects in the bottom of the container
and it gets ended up being tipped down the drain and there you can see it. Most of that
is water. There's a little bit of shellite sitting on top of it but the majority of that is water.
This is the heat gun that we're going to use to dry off the rest of the shellite
off the parts. It's on low. We don't want the parts to get too hot. Spin them round
so that we get full coverage of warm air over all of all of the parts on each of the parts too.
Pendulum bob, straight wheel, strike side wheels, back plate, count wheel
and the front plate. A final quick run over them. Right we're back at the bench again. We've got
our clean parts here. Front plate. That's the strike side. Great wheel. Going side great wheel.
They all look pretty clean. All the oil's gone from them. They've come up rather nicely.
Going side wheels. Escape wheel sitting on the top of it. That's the first wheel. Yep they look
pretty good. They're heaps cleaner than when they went into the ultrasonic that's for sure.
What else have we got in here? Great wheel on the going side train. Yep looks rather nice.
Now you'll notice there someone has scratched a large R on that great wheel. You don't do that.
If you must mark any part of a clock, use one or two tiny little punch marks
and that's all you need to do. You don't need to deface it. Count wheel. Yep cool. Looks pretty good.
Back plate. Putting the side over there. Pendulum bob. Yeah that's the nuts that hold the plates
together. We'll put that clip over there. That's the clip that holds the count wheel on.
The fast slow mechanism goes back in there. Very shiny. Lovely. Put that away. Great wheel
on the going side train. Put him over in his container. Great wheel from the strike side.
You see the piece of wire we put on it to differentiate it. Don't need that anymore.
I'll cut that off. Put it over in this container. Motion works. There's the other piece. There we go.
All together. That top piece there is called the cannon arbor. That's the one that the hour hand
sits on. The minute hand sits on that inner one with the rectangle cut on the top of it.
Strike side wheels. I'll cut the wire on that so we can put them into the block again.
That's better. Bit easier to see for you. Take that wire off. Get rid of that. Maintenance cam.
First wheel. And now the going side train. Undo the wire on that. First wheel. Second wheel.
Third wheel. And the escape wheel goes right at the top of the train.
