A&A Tactical: SEACU-Cummerbund V2-B JPC/AVS Variant

Ballistic Lab
1 follower
Dec 12, 2025
A&A Tactical: SEACU-Cummerbund V2-B JPC/AVS Variant
Alright guys, I got some longer projects that I'm plugging away on, but it's been a little while since I put something out.
So, tonight we're going to talk about the newest version of the ANA Technical Cumberbund.
I believe it's still the CQ Cumberbund.
But these things keep getting better and better, and there's a lot of
small features that I want to kind of show you guys on this thing.
So we're gonna have to put it on the table to break them all down, but there's been some
in my mind, significant improvements, especially since the first generation that I got from Austin.
So we'll look at this. I'll show you kind of the ins and outs.
This one is easily the best one to date. There's still a little bit of room for improvement in my mind,
but they're small steps. This has come a long, long ways since the first one.
So let's put it on the table, and I'll show you
kind of the ins and outs, and I'll also give you guys a comparison on
sizing compared to a stock JPC Cumberbund.
Because I haven't done that before, and it kind of matters. So let's take a look at this thing a little bit closer.
Okay, so I want to knock this out before we get too far into this so I can get the JPC off the table.
But I don't think I've done a side-by-side comparison between a
two-cell CQ Cumberbund and a stock JPC Cumberbund. So this is a medium JPC 2
with what I believe is the stock
medium Cumberbund on there. So
this might not line up perfectly, but if you
look at the end of the Cumberbund here, and we line that up,
you can see that the
MOLLE portion of the Cumberbund on
the stock Cumberbund stops kind of middle of the
the first cell on the CQ Cumberbund. So the CQ Cumberbund, as
it sits, granted, you know, everything from Austin can be customized to a certain extent, is
a hair longer than the stock Cumberbund. Now that really doesn't matter too much because you can always
bundle up the end of your CQ Cumberbund or your JPC Cumberbund for that matter if it's too long.
But if you, again, if you line up the end here, and this is a little off, the
vertical ribbon on the JPC Cumberbund
kind of falls in line perfectly with the end of the the MOLLE or skeletonized portion on the CQ Cumberbund.
So while you have some room to
potentially go
longer on the CQ Cumberbund, you can also tighten it up just as much as the
JPC one. If we really stretch that out, let's see here.
You've got
one column of room to one additional column that you can tighten this one up
before you bottom out on
the zipper with this vertical portion.
If you get to that point, a two-cell Cumberbund is not going to work for you anyways.
And you're a legitimately tiny human being at that point in time, and you would have to go with a one-cell.
Which you could absolutely do. If you needed to get that small,
you could order a one-cell from Austin.
That would give you, and you could you could get extra MOLLE, right? So if you're, I would say
if you wear a size
30 pant and below, maybe consider that. I know pants don't necessarily tie in with plate carrier sizing.
But if you wear a size 30 pant, and you don't
have internal radios or
side armor,
consider doing a one-cell. If you do side armor, you're gonna have to get the two-cell to support it.
Effectively.
So you're kind of stuck there, but no side armor, no internal radios,
size 30 pants, you could you could cut it down to a single cell
so that you're not rolling the dice on being able to get it small enough.
The other option is, if you if you go with this setup, and it's too big for you,
in the meantime, you just go on top of the zipper, and you can get a little bit smaller, because you don't necessarily have to weave
through the the vertical webbing on the JPC. It's gonna real be real janky, not an ideal setup,
but you can make it work until you found a different solution.
So we'll get the the JPC out of the way here,
so we can look at some of the finer details on
the SeaCucumber one, the most current version. So
the setup really hasn't changed
in theory very much
over the different generations.
But it's been refined more and more and more as we go along. So I originally said when I first
covered the the Cumberbund from Austin,
huge fan, the only downside I had at the time was that I couldn't use
side armor with the the SeaCucumber one. So that got fixed on the last generation as an option,
I believe. I don't think this is a required setup, but
it's got internal molle.
So any molle on side plate bags can can be stuck internal of the the SeaCucumber one, or if you wanted them
external of your magazines or these cells, for whatever reason, you could just mount it backwards, and that would work just as well.
The the tubes you might have to reconfigure, because the the pull tabs aren't set up for
side plates internal. I'm sure you could sort that out with with no concern.
But so you have four columns of usable molle
internal to the the current generation of the SeaCucumber one.
A while back talking, I think it was public, talking with Blake
from Blakewater fame,
you
you're a little bit limited in the the location of your side armor
with this setup, because you have to have your side armor right here. So if you have internal radios,
they might be a little bit close to the front plate bag.
If you don't have internal radios, there might be a little bit of a gap off the front plate bag.
So it just kind of depends on where you want your side plates to sit.
I think that
you could you could make do, if you had to get this further from the front plate bag, you could you could stagger
your your side armor a little bit, and
and figure out a way to
offset at one column. It may not be the cleanest setup, but it would work, and I don't think you'd have any
issues other than having to do a little bit of arts and crafts, potentially with some zip ties.
So your side plates are kind of fixed in in position when you're using this setup. That said, if you
are using your tubes
with a tubes adapter type setup, which is what we've got here,
so I can put my
male tubes on the adapter,
you do have a little bit of finite control because you can put this, you know, further to one side on the plate bag or
overlap it a little bit more
to do that that final tweaking there. If you're if you're attaching your tubes to a placard,
then you're really stuck. Like you you can't you can't move your tubes one way or the other. So
that's an option, and I don't know for sure if these come with the the cummerbund, so I apologize for that. This was
sent to me by Austin, so I don't know pricing and whatnot. I totally forgot to check, and I apologize.
All right.
So side plates, it is compatible. Location is kind of fixed.
The
the stitching on here, you know, Austin never had bad stitching by any stretch,
but these things are cleaner and cleaner and cleaner, and you can see
the stitch lines are super nice on this thing.
Nothing looks like an afterthought on here. It is it is all very well done.
So you still have the same dual cell
setup as the old CQ cummerbunds.
So you've got your kind of pistol size cell on the outside and then rifle size cell on the inside.
It does get a little snug if you're using both for magazines.
So with an M4 mag and a pistol mag, it's a little taut.
Not a huge deal. I never particularly used these outer cells for pistol magazines, though.
Potentially a flashlight or a multi-tool or just a couple of chemlights is kind of what I use them for.
It's really about the the internal
M4 mag pouch
or M4 mag sized pouch.
And then the the external one was just kind of a in case I needed it kind of thing.
And in a lot of instances it was even the the rear cell was just kind of it was there if I needed it.
It's a cummerbund with like a built-in 10-speed capability.
So I
can't remember if the last generation had
provisions for shock tube routing or shock cord routing. Excuse me. Don't route shock tube through there.
That would be silly.
Shock cord routing.
So the new ones obviously do. We've got these nice laser-cut eyelets there.
So they are external of the pistol size cell and then internal on the rifle size cell. So you get one
retention kind of per two cell setup.
The retention that came with this
is really well done. So you've got your your standard size shock cord there.
You could go thinner or thicker depending what you need.
But then he's got these awesome
pull tabs here. So
you've got nice dual
loop setup there so you can configure that however you want. And then this awesome pull tab
with some grippy material. I apologize. I have no idea what this material is called, but it's got a little bit of grippiness to it.
You guys have seen it on other products before. It kind of has like a high blonde feel to it, but not quite.
And it works
very similar to like a soft S&S Precision pull tab.
Really cool setup. And you could you could configure that either way
depending on how you routed your shock cord.
You could have it sit like this if you wanted to. It might take a little bit more
configuration or a little bit weaving time.
Or you can just have it like this. I think if you just ran one band through there.
So it would work out really well.
And it, you know, it spreads out so it'll actually sit kind of on top of your magazine.
Especially if you just just figure it out with your M4 mag.
And then you've got a nice vertical pull tab. When that's sitting on the mag like that,
it's gonna stick up and be right there easy to grab.
And then if if retention is not your jam, you don't have to use it. And it's out of the way.
And these tabs kind of act a little bit like a
re-indexing tab.
I could see
making the case to just ignore the the pistol side and put the second tab only on the rifle side.
And then you could really use it for a re-indexing tab.
Just hook the corner of the magazine between those and and plop it right in there. That would work out pretty well.
I think it would, I think it'd be good. It would be great.
I don't necessarily need the retention on the pistol side. So just because they tend to be
shorter objects that will sit in there just fine.
You know nitpicking another another complaint. Some people really really get bothered by open bottoms on these things and I get it.
If you're in the camp that you need closed bottoms.
Totally feel it. I don't know if Austin could find wider
elastic and just sew that across the bottom.
But I've had bad results with that where it's just too much tension on the bottom of the pouch and it ends up
kind of pooping out whatever was in there. I've had water bottles do that
and it was not a fun day when it came out.
So you've got the the new retention option. You've got the the side plate options.
This one is terminated in tubes. You don't have to get it terminated in tubes. You can you can have traditional velcro on the front.
Obviously you can't you know swap back and forth unless you do some arts and crafts with this and just
delete the tube and zip tie that on there. You could do it.
But from from Austin you can kind of choose either or do you want velcro or do you want tubes?
Sizing we already kind of talked about that.
This is kind of the limit for where you can shorten it up.
But if you're if your torso between plates is smaller than this
hopefully you recognize that and you plan accordingly.
But yeah, these are these things huge huge fan.
Adding the side plate capability in my opinion
really really solved all of the the hard issues that I had with this.
Because if you need side armor you need side armor and if you want side armor you want it and
and a cummerbund that doesn't support that is kind of a non-starter from the get-go.
You don't necessarily want to run two cummerbunds just so you can have side armor.
So these things like I said keep getting better and better. This is a cleanest one for sure the most functional one and
I
am happy to put these on any
platform that supports them. If you don't have a
skeletonized
friendly vest you can always get these
terminated like the Pharaoh concept style with just velcro. I know he's not the only one that does them that way.
But he's I think that's kind of just what we're calling it these days is the Pharaoh style versus the JPC style.
These will work in scarabs just as well. I had one in my scarab before I sold it.
They'll work in LV-119s,
JPCs, SPCs, AVS.
They'll play with the
the axle micro harness or the regular harness or the AVS-1000.
This style really gives you kind of all the flexibility that you need in my opinion.
And if you want to put it on a Pharaoh style vest you just get the grid adapter from VXV Concepts
and it'll work just as well. And then the cool thing with the grid adapter is
it makes your cummerbund even though it's the lacing style a quick swap. So if you
have one of these that's not side plate compatible
you can put it on there with the grid and then you can immediately tear it off and swap in a side armor setup.
So if you've got the longer cry soft armor panels
you can have one cummerbund set up like that and another one set up without.
Lots of options. I really prefer the the skeletonized JPC style or the lacing. You get better finite control over
the sizing on the back and
it's really a win in my opinion. I would not voluntarily
go with the the Pharaoh style cummerbund anymore. There's just no reason to.
So thanks to Austin for sending me this.
I'm gonna I'm gonna put it on my JPC as soon as I'm done with this video
but I wanted you guys to have kind of an unobstructed view of it and
see how that fits. So thanks for your time guys.
15 minute video on a cummerbund so you can tell I'm a big fan of these things.
