1960's Omega Seamaster 120 Basic Restoration

Antique Adventures
14 followers
#Vintagewatch #AntiqueClock #HistoryDesign #VintageClock
This little beauty needed a few things done in order to ensure its safe whilst being used out in the wild. The gasket was completly perished which meant it wasnt waterproof, and the small crumbs of hardened rubber could dislodge and fall into the movement. I hope you enjoy this basic restoration.
Hello, my name is Elliot and today we're going to be having a go at fixing up an Amiga Seamaster 120.
This one has the reference 166.027. I picked this thing up recently, it's in really nice condition,
I'm very happy with it. Obviously there's a few scuffs, we can sort out the plexiglass,
but as for the case, I mean it's light scratches and general wear but I'm definitely not going to
be doing any polishing to it because the more you polish stuff the less original it becomes.
Plus for a watch that's 50 odd years old, you know, you can expect a few bits of wear.
So I'm going to start by removing the bracelet. This has a small spring bar that you have to
pull back and then you can go ahead and remove it. Now we're going to give the case and bracelet a
clean in the ultrasonic cleaner. You can see there there's just some general dirt and stuff that's
built up over the years. Now this isn't the right tool, I should mention I'm not a watchmaker and
don't really have any experiences with watches, so we should see how this goes. Now I'm going to
remove the case back and we're going to get a good look at the problem that we need to sort out today,
the main issue. Look how beautiful that movement is inside. So as you can see around the edges,
a lot of built up black stuff has occurred and that right there is the rubber gasket that has
basically just perished over the years. So on the top layer it's sort of gone a crusty black
crumbly material and underneath it's a gloopy sticky residue which is very difficult to clean
off. Now I just removed the crown there that's achieved by pressing a small little lever and
then we're going to undo the case screws and remove the feet that are holding that in so that
then we can flip the movement over and take the case off of the dial. We're then going to cover
that up and move it off to the side and we can work on the case which is a part that's a little
bit more forgiving than the movement when you've got absolutely no experience with watches.
So I'm going to take my needle nose tweezers and we're going to just go ahead and remove as much
of that gunk as possible. Now as I said it's gone all crumbly on the top and that wouldn't be an
issue if it was like that all the way through but what you then have underneath that is a really
gloopy sticky residue which is very very difficult to get off and you can't just scrape it off in one
clean movement because this thing is stuck inside of a small recess that's probably two millimeters
wide. But we need to do this for many reasons this is going to cause the movement potential
problems if some of this stuff dislodges and works its way into some of the small wheels.
The other reason is that it's now no longer serving a functional purpose it's not making
the watch waterproof. This watch is probably not ever going to be waterproof by the initial
initial 120 meter specification but it'd be nice to know that it's safe in the rain and
when you're washing your hands. So I'm going to use some isopropyl alcohol on the case back
which is a lot easier to clean because obviously you've got that lip there that you can just rub
down with a cotton bud and that's going to go ahead and clean that all off. But the actual
case back itself is not the hardest part to clean you've got to remove the whole crumbly pile of
mess within the case. Now using isopropyl alcohol did make a huge difference I then took the toothbrush
and scrubbed it out and the bristles were able to make a really good impact on cleaning the inside
but what's going to finish it off is the ultrasonic cleaner. Now this cheap little
Chinese ultrasonic cleaner is not ideal for watchmaking and in fact it broke halfway through
attempting this and I've only used this thing twice so that's good but my friend David lent me
some of his tools and we cleaned up the case off camera so it's all nice and clean now but you can
see the ultrasonic cleaner doing its job there. It's all clean we're going to now have a go at
polishing the plexi. Now this is a material called poly watch that's basically just a small
little polish with a very fine grit inside that's going to essentially sand down a layer of the
plexiglass and remove all the deep scratches. Now you can't do this on glass or sapphire crystal
obviously but on plexiglass which is basically a plastic it is something that you can do and
the difference it has on the watch's overall look is just unreal. You might be able to see in the
center a small Amiga symbol on that plexiglass that obviously shows that this plexiglass is
original and although you can replace the plexiglass it's going to be pretty hard to find
an original Amiga one. So this was it getting it back from David who's given it a good clean at
this point and yeah you can see now it's really starting to look quite beautiful again. So once I
struggle to undo this case back we're then going to have a go at putting the watch back together.
Now we're going to give everything a blowout with a small little duster but typically what you do is
have a sort of an airline on a very high pressure which is going to spray out a very controlled
stream of air and that's going to help you blow away dust so this isn't going to be dust free.
I'm not in a dust free environment I'm just in my bedroom. I'm going to go ahead and re-insert
the crown which is fairly straightforward but I'm still learning the sort of tolerances with
everything. So now we're going to go ahead and insert the gasket. No we're not we're going to
put the case feet in to hold the case sorry to hold the dial in the case. This isn't scripted
this is the first time I'm trying a video like this so let me know what your thoughts are. So
yeah we're going to go ahead and set that foot in and then do the same on the other side and then
we can insert the screws. Now these screws are absolutely tiny I mean absolutely tiny and
it's quite scary working in this little small thing because one slip of the screwdriver and
that could be a catastrophic unrecoverable damage. So I'm going to use this small little oiler and
oil up the gasket with a small little bit of essentially grease and that's just going to help
with the seal and then we're going to just fit it into the little crevice that it has to go in
make sure it's all nice and in there properly give the movement one little
blow with the blowy thing and then go ahead and put the case back on. That's pretty much it after
that it's just putting the bracelet back on which is all now nice and clean as well from the
ultrasonic cleaner. I think David also used a small little jet wash like a very small one that's
for watches and there we have it look at that you can see the dial now far more than you could
previously and I have the knowledge that there's not a deteriorating old piece of rubber causing
problems and it's also now obviously splash-proof. I'm very pleased.
